1. One-Dimensional Steady-State Conduction
Chapter 3
One-Dimensional Steady-State Conduction
Chapter 3
Chee 318

2. One-Dimensional Steady-State Conduction
Conduction problems may involve multiple directions and time-dependent conditions
Inherently complex – Difficult to determine temperature distributions
One-dimensional steady-state models can represent accurately numerous engineering systems
In this chapter we will
Learn how to obtain temperature profiles for common geometries with and without heat generation.
Introduce the concept of thermal resistance and thermal circuits
Chapter 3
Chee 318

3. The Plane Wall qx x=L x=0 x
Consider a simple case of one-dimensional conduction in a plane wall, separating two fluids of different temperature, without energy generation
Temperature is a function of x
Heat is transferred in the x-direction
Must consider
Convection from hot fluid to wall
Conduction through wall
Convection from wall to cold fluid
Begin by determining temperature distribution within the wall qx x
x=0
x=L
Hot fluid
Cold fluid
Chapter 3
Chee 318

4. Temperature Distribution
Heat diffusion equation (eq. 2.4) in the x-direction for steady-state conditions, with no energy generation:
qx is constant
Boundary Conditions:
Temperature profile, assuming constant k:
(3.1)
Temperature varies linearly with x
Chapter 3
Chee 318

5. Thermal Resistance (3.2a) (3.2b) (3.2c)
Based on the previous solution, the conduction hear transfer rate can be calculated:
(3.2a)
Similarly for heat convection, Newton’s law of cooling applies:
(3.2b)
And for radiation heat transfer:
(3.2c)
Recall electric circuit theory - Ohm’s law for electrical resistance:
Chapter 3
Chee 318

6. Thermal Resistance
We can use this electrical analogy to represent heat transfer problems using the concept of a thermal circuit (equivalent to an electrical circuit).
Compare with equations 3.2a-3.2c
The temperature difference is the “potential” or driving force for the heat flow and the combinations of thermal conductivity, convection coefficient, thickness and area of material act as a resistance to this flow:
Chapter 3
Chee 318

7. Thermal Resistance for Plane Wall
Cold fluid
In terms of overall temperature difference: qx
Hot fluid
x=L
x=0 x
Chapter 3
Chee 318

8. Composite Walls
Express the following geometry in terms of a an equivalent thermal circuit.
Chapter 3
Chee 318

9. Composite Walls What is the heat transfer rate for this system?
Alternatively
where U is the overall heat transfer coefficient and DT the overall temperature difference.
Chapter 3
Chee 318

10. Composite Walls (a) Surfaces normal to the x-direction are isothermal
For resistances in series: Rtot=R1+R2+…+Rn
For resistances in parallel:
(1/Rtot)=1/R1+1/R2+…+1/Rn
(b) Surfaces parallel to x-direction are adiabatic
Chapter 3
Chee 318

11. Example (Problem 3.15 textbook)
Consider a composite wall that includes an 8-mm thick hardwood siding (A), 40-mm by 130-mm hardwood studs (B) on 0.65-m centers with glass fiber insulation (D) (paper faced, 28 kg/m3) and a 12-mm layer of gypsum (vermiculite) wall board (C).
What is the thermal resistance associated with a wall that is 2.5 m high by 6.5 m wide (having 10 studs, each 2.5 m high?)
(Note: Consider the direction of heat transfer to be downwards, along the x-direction)
Chapter 3
Chee 318

12. Contact Resistance
The temperature drop across the interface between materials may be appreciable, due to surface roughness effects, leading to air pockets. We can define thermal contact resistance:
See tables 3.1, 3.2 for typical values of Rt,c
Chapter 3
Chee 318

13. Alternative Conduction Analysis
When area varies in the x direction and k is a function of temperature, Fourier’s law can be written in its most general form:
For steady-state conditions, no heat generation, one-dimensional heat transfer, qx is constant.
Chapter 3
Chee 318

14. Example 3.3
Consider a conical section fabricated from pyroceram. It is of circular cross section, with the diameter D=ax, where a=0.25. The small end is at x1=50 mm and the large end at x2=250 mm. The end temperatures are T1=400 K and T2=600 K, while the lateral surface is well insulated.
Derive an expression for the temperature distribution T(x) in symbolic form, assuming one-dimensional conditions. Sketch the temperature distribution
Calculate the heat rate, qx, through the cone. T2 T1 x1 x2 x
Chapter 3
Chee 318

15. Radial Systems-Cylindrical Coordinates
Consider a hollow cylinder, whose inner and outer surfaces are exposed to fluids at different temperatures
Temperature distribution
Chapter 3
Chee 318

16. Temperature Distribution
Heat diffusion equation (eq. 2.5) in the r-direction for steady-state conditions, with no energy generation:
Fourier’s law:
Boundary Conditions:
Temperature profile, assuming constant k:
Logarithmic temperature distribution (see previous slide)
Chapter 3
Chee 318

17. Thermal Resistance
Based on the previous solution, the conduction hear transfer rate can be calculated:
Fourier’s law:
In terms of equivalent thermal circuit:
Chapter 3
Chee 318

18. Composite Walls
Express the following geometry in terms of a an equivalent thermal circuit.
Chapter 3
Chee 318

19. Composite Walls What is the heat transfer rate?
where U is the overall heat transfer coefficient. If A=A1=2pr1L:
alternatively we can use A2=2pr2L, A3=2pr3L etc. In all cases:
Chapter 3
Chee 318

20. Example (Problem 3.37 textbook)
A thin electrical heater is wrapped around the outer surface of a long cylindrical tube whose inner surface is maintained at a temperature of 5°C. The tube wall has inner and outer radii of 25 and 75 mm respectively, and a thermal conductivity of 10 W/m.K. The thermal contact resistance between the heater and the outer surface of the tube (per unit length of the tube) is R’t,c=0.01 m.K/W. The outer surface of the heater is exposed to a fluid of temperature –10°C and a convection coefficient of h=100 W/m2 .K.
Determine the heater power per unit length of tube required to maintain the heater at To=25°C.
Chapter 3
Chee 318

21. Spherical Coordinates
Fourier’s law:
Starting from Fourier’s law, acknowledging that qr is constant, independent of r, and assuming that k is constant, derive the equation describing the conduction heat transfer rate. What is the thermal resistance?
Chapter 3
Chee 318

22. Example (Problem 3.69 textbook)
One modality for destroying malignant tissue involves imbedding a small spherical heat source of radius ro within the tissue and maintaining local temperatures above a critical value Tc for an extended period. Tissue that is well removed from the source may be assumed to remain at normal body temperature (Tb=37°C).
Obtain a general expression for the radial temperature distribution in the tissue under steady-state conditions as a function of the heat rate q.
If ro=0.5 mm, what heat rate must be supplied to maintain a tissue temperature of T>Tc=42°C in the domain 0.5<r<5 mm? The tissue thermal conductivity is approximately 0.5 W/m.K.
Chapter 3
Chee 318

23. Summary
We obtained temperature distributions and thermal resistances for problems involving steady-state, one-dimensional conduction in orthogonal, cylindrical and spherical coordinates, without energy generation
Useful summary in Table 3.3
Chapter 3
Chee 318