1. RECAP OF THE LAST LESSON
TALKIE TIME
RECAP OF THE LAST LESSON

2. Learning Objectives: Finds the answers to research questions (CG)
Gathers and analyze the data using appropriate techniques (CG)
Presents the data; gives analysis and interprets the data (Addendum)

3. Application: Produce a Table and Discussion
Pre-Activity :
Application: Produce a Table and Discussion

4. (Oryctolagus cuniculus)
THE HEPATOPROTECTIVE EFFECT OF NEEM (Azadirachta indica) LEAF CRUDE EXTRACT ON ACETAMINOPHEN-INDUCED HEPATOTOXICITY IN MALE RABBITS
(Oryctolagus cuniculus)

5. HOW ABOUT IN APPLIED RESEARCH

6. Drainage Management System Using Ultrasonic Sensors

7. THE PROBLEM
Statement of the Problem
The researcher sought to innovate a new drainage system management with use of ultrasonic sensor. The main aim of this study is to provide a real-time information on the drainage condition and water level detection.
Specifically, the study sought to answer the following questions:
1. What is the Operation Design of the researcher-made drainage management system?
2. What Materials and Procedures are used the researcher-made drainage management system?
3. How functional is the proposed design based on its purpose?
Assumption: The researcher-made drainage management system is effective in providing a real-time information on the drainage condition and water level detection.

8. Results and Discussion

9. I-A. The Operation Design – Block Diagram
The operation design of the proposed drainage management system using ultrasonic sensors is to locate clogs for an early flood response. Figures 1 illustrates the block diagram of the ultrasonic sensor of the design project.
Figure 1. Block diagram of the ultrasonic sensor

10. I-B. Operation Design - The Programming
The researcher collected different programs for each sensor from the Arduino website. The codes were compiled and modified to fit the use to be obtained using the Arduino software. Extensive revision and analysis were done in order to achieve the expected code. Figure 2 illustrates the program flow chart of the whole project.

11. Figure 2. Program Flow Chart

12. I-C. Operation Design – The Set Up
Mechanism of Ultrasonic Sensor
The Ultrasonic sensor detects the distance of any object without the sense of touch. It is set into repeatable mode, meaning it will continue to detect any object’s distance until it ends. The sensor is given a ten-second calibration time and after that, it runs.
This sensor contains lenses that determines its detection range. It is said to have a minimum and maximum range of 2 to 400 centimeters according to the manual. The sensor is then set to its maximum range.

13. Figure 3. Ultrasonic Sensor Schematic Diagram

14. According to the program, the sensor will only send a high signal once the distance of uneven water levels are detected.
The system was then tested in various situations with a clog in different areas of the drainage system. This is to ensure the accuracy of the whole system.
An LED, along with a piezo element buzzer, is paired up with each Ultrasonic set-up that turns on when the coniditon is met. Thus, if an LED and buzzer emit light aand sound respectively, then it must mean there is a block within its area.

15. Figure 4. Ultrasonic Range Finder

16. II. Materials and Procedures :
The researcher will use the following materials:
3 HC-SR04 Ultrasonic Sensors
Male-Male Connectors
Male-Female Connectors
Female-Female Connectors
USB Cable A to B
Arduino Mega 2560 Microcontroller
3 Piezo Element Buzzer
3 LEDs
Arduino Software (version 1.6.9)
Soldering iron
Lead
Sealant
32in x 6.5in x 13.5in Case (Prototype Set-Up)
The researcher obtained the materials needed from 3M Electronix in Basak-Marigondon Road, Lapu-Lapu City, from Bitstoc Electronics in Tres Borces Padres Street, Cebu City, and unused materials from School Stockroom.

17. 1 x HC-SR04 module

18. VCC = +5VDC
Trig = Trigger input of Sensor
Echo = Echo output of Sensor
GND = GND

19. The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.

20. Figure 6.3. Programming of the First Ultrasonic Sensor

21. Figure 6.5. Programming of the Third Ultrasonic Sensor

22. Figure 8. Primary Set Up of the Program

23. Figure 9.1. Creation of the Prototype Drainage 1

24. Figure 10.3. Creation of the Drainage Prototype 2

25. READINGS (in cm) LOCATION OF THE BLOCK Depth of Set-Up Conclusion 1st
III. Functionality Test
LOCATION OF THE BLOCK
Depth of Set-Up
READINGS (in cm)
Conclusion
1st
Sensor
2nd
3rd
Sector 1
27cm 17 27
Block in Sector 1 was detected
LOCATION OF THE BLOCK
Depth of Set-Up
READINGS (in cm)
Conclusion
1st
Sensor
2nd
3rd
Sector 2
27cm 27 16
Block in Sector 2 was detected

26. As the program coded runs, the researcher observes that the system runs all together. The operation of the drainage management system set-up is based on the readings of the ultrasonic sensors. The data collected by the ultrasonic sensors are fed into the system to be displayed in a serial monitor. Once an unequal reading is found between two sensors (i.e., Sensor A is greater than Sensor B), and equal reading is found between another two sensors (i.e., Sensor B is equal to Sensor C), then there is a clog or block in the system, therefore the function of this system is to detect clogs based on the ultrasonic sensors’ readings and their conditions programmed.
As an unequal reading is gathered from two different areas/ultrasonic sensors, an LED and Piezo element buzzer is activated to dictate a block in the system. It is observed that the system is delayed by one-fourth of a second or 25 milliseconds.

27. APPLICATION: Present a mock up data. (Individual)

28. ROBOTRASH 2.0: WASTE SEGREGATOR ROBOT
Statement of the Problem 
The engineering research will produce a Robot that segregates trash.
Specifically, it answers the following questions.
What program design can be utilized to produce the waste segregator robot?
What materials and Testing Procedures can be developed to produce the Robot?
How functional is the Robot in segregating wastes?
What is the perception of the selected samples who used the Robot?