Presentation is loading. Please wait.

Presentation is loading. Please wait.

Now What? Forgot to Pull a Permit?

Published byIris Shields Modified over 6 years ago

Similar presentations

Presentation on theme: "Now What? Forgot to Pull a Permit?"— Presentation transcript:

1 Now What? Forgot to Pull a Permit?
Promised to get that system piped today? Now What?

2 Imagine Flameless Assembly
for Refrigeration ZoomLock! Braze-less Fittings

3 ZoomLock Braze-less Fittings
ZoomLock Technology Flameless Solution Green Technology Minimal Skill-set Required

4 Technology Comparison
ZoomLock Fittings BRAZING Torch Kit with Gas Regulators Gas Tanks (2) Tubing Cutter De-burring Tools Degreaser Scotch Brite Cooling Rag Access To Water for Cleaning and Cooling Solder and Flux Fire Extinguisher Fire Safety Equipment Burn Permit (Auth. For Open Flame) Fire Spotter RLS Crimping Set Tubing Cutter De-burring Tools Scotch Brite Rag

5 Imagine No More! ZoomLock!

Download ppt "Now What? Forgot to Pull a Permit?"

Similar presentations

Say Goodbye to nuts, clamps, crimping, welding, or soldering and say Hello to the Quick Fitting, Inc. COPRO quick connection fitting technology. The.

Say "Goodbye" to nuts, clamps, crimping, welding, or soldering and say "Hello" to the Quick Fitting, Inc. COPRO quick connection fitting technology. The.
HVAC523 Soldering.

HVAC523 Soldering.
NERI TORCH TRAINING PART VII PRACTICAL EXAM PREPARATION.

NERI TORCH TRAINING PART VII PRACTICAL EXAM PREPARATION.
4.2.16 Student Book © 2004 Propane Education & Research CouncilPage 1 4.2.16 Installing Copper Tubing in Distribution Systems Personnel who install copper.

Student Book © 2004 Propane Education & Research CouncilPage Installing Copper Tubing in Distribution Systems Personnel who install copper.
Trade of Plumbing – Phase 2 Module 2 – Unit 6 Module 2: Domestic Hot and Cold Water Service Unit 6 – Soldering Duration – 32 Hours.

Trade of Plumbing – Phase 2 Module 2 – Unit 6 Module 2: Domestic Hot and Cold Water Service Unit 6 – Soldering Duration – 32 Hours.
Oxy – Fuel Torch Ag Mechanics.

Oxy – Fuel Torch Ag Mechanics.
1 HVACR316 – Piping Torches, Tanks, and Tips. 2 Soldering Basics Soldering is a process used to join piping and tubing to fittings. It is used primarily.

1 HVACR316 – Piping Torches, Tanks, and Tips. 2 Soldering Basics Soldering is a process used to join piping and tubing to fittings. It is used primarily.
Soldering Brazing and Braze Welding

Soldering Brazing and Braze Welding
Gas Heating, Cutting, Brazing, and Welding

Gas Heating, Cutting, Brazing, and Welding
1 REFRIGERATION FUNDAMENTALS HVAC/R. 2 SOLDERING & BRAZING When and why; –When an A/C or refrigeration system is entered, it must be properly sealed –Although.

1 REFRIGERATION FUNDAMENTALS HVAC/R. 2 SOLDERING & BRAZING When and why; –When an A/C or refrigeration system is entered, it must be properly sealed –Although.
SAFETY TALK - SLIDE 1 OF 14 Elkhart Products Corporation 08/00 WELCOME ELKHART PRODUCTS CORPORATION “TOOLBOX SAFETY TALK” Welding, Cutting, & Burning.

SAFETY TALK - SLIDE 1 OF 14 Elkhart Products Corporation 08/00 WELCOME ELKHART PRODUCTS CORPORATION “TOOLBOX SAFETY TALK” Welding, Cutting, & Burning.
SWEEP CHARGE PROCEDURE Page 1 - 5. SWEEP CHARGE EQUIPMENT & SAFETY TANK OF LIQUID REFRIGERANT DO NOT: Drop or handle tank roughly Tamper with the safety.

SWEEP CHARGE PROCEDURE Page SWEEP CHARGE EQUIPMENT & SAFETY TANK OF LIQUID REFRIGERANT DO NOT: Drop or handle tank roughly Tamper with the safety.
Section 2 Safety, Tools and Equipment, Shop Practices Unit 4 General Safety Practices.

Section 2 Safety, Tools and Equipment, Shop Practices Unit 4 General Safety Practices.
Andrew Brock. Terms  The burning qualities of gases are used in Ag Mechanics to heat, weld and cut metals  Weld- to join by fusion  Fusion- melting.

Andrew Brock. Terms  The burning qualities of gases are used in Ag Mechanics to heat, weld and cut metals  Weld- to join by fusion  Fusion- melting.
Agricultural Mechanics Fundamentals & Applications Chapter 22—Using Gas Welding Equipment.

Agricultural Mechanics Fundamentals & Applications Chapter 22—Using Gas Welding Equipment.
Welding, Cutting, & Burning. GENERAL HAZARDS General hazards of welding include: –Impact –Penetration –Harmful dust –Smoke –Fumes –Heat –Light radiation.

Welding, Cutting, & Burning. GENERAL HAZARDS General hazards of welding include: –Impact –Penetration –Harmful dust –Smoke –Fumes –Heat –Light radiation.
HazMat Technician Mod 1 Unit 6 Slide 1 Ohio Hazmat & WMD Technician Module 1 Unit 6 Control, Containment and Confinement.

HazMat Technician Mod 1 Unit 6 Slide 1 Ohio Hazmat & WMD Technician Module 1 Unit 6 Control, Containment and Confinement.
Our History Murad Hardware was established in the year 2000. Shortly after the establishment, it has achieved an exclusive partnership with JOR paints,

Our History Murad Hardware was established in the year Shortly after the establishment, it has achieved an exclusive partnership with JOR paints,
It is amazing to be able to join metal using heat. The process we use in making jewelry is called soldering… it is closest to brazing in the world of.

It is amazing to be able to join metal using heat. The process we use in making jewelry is called soldering… it is closest to brazing in the world of.
Lumbermen’s Underwriting Alliance

Lumbermen’s Underwriting Alliance

Similar presentations

Ads by Google