1. MATERIAL SCIENCE HONORS
CUSTOMIZING METALS

2. What is Cold Working?

3. Altering the size or shape of a metal by plastic deformation.
Cold-Working
Altering the size or shape of a metal by plastic deformation.

4. Cold-Working
. Cold working produces additional dislocations within the metal structure.

5. Cold working is often referred to as work hardening.

6. Metals are Malleable

7. Metals are Flexible!
If a metal is stressed in tension beyond its elastic limit, it elongates slightly.

8. This elongation (slip) occurs in the direction which atoms are the most closely packed since it requires the least amount of energy.

9. All the slip that occurs in a metal is caused by the movement of dislocations in its crystal structure.

10. Dislocations are lines of defective bonding.

11. When 2 or more dislocations meet, the movement of one tends to interfere with the movement of the other.

12. The number of dislocations in a metal crystal structure build up as the metal is cold worked.

13. Atomic Structure
The diagram shows a polished and etched metal surface with tiny ridges on the surface where groups of slipping planes of atoms actually stick up, and thus it reveals the typical slip direction in each crystal.
The more dislocations there are, the more they will hinder each other's movement.

14. Effects of Cold Working
Cold working improves tensile strength, yield strength and hardness.

15. Effects of Cold Working
Cold working reduces ductility and flexibility.

16. Lab: Cold Working 1

17. Lab: Cold Working 1
Metal Sample
# of Turns
Non-hammered
Hammered

18. Cold working does not increase the ultimate stress of a metal.
However the cold working does not increase the ultimate strength of the material. So in a sense, cold working uses up some of the safety margin of the material. If a very strongly cold worked material is overloaded, it could well just break like a brittle material with no warning. So we try to design cold working as a compromise. A little bit can be good: too much could be dangerous.
Cold working uses up some of the safety margin of the metal!

19. Flow Stress
Flow Stress is the shear stress required to cause plastic deformation of solid metals Here the flow stress, sigma f, is commonly a power function of the strain where K is the strength coefficient and n is the strain hardening exponent.

20. A little cold working could be a good thing.
The added strength is worth the loss of flexibility.

21. That comes in handy when you are stringing a fence!
Example-Fencing Wire
Cold working allows you to pull harder on the wire before it stretches (deforms).
That comes in handy when you are stringing a fence!

22. Types of Cold Working

23. Rolling

24. A metal strip is passed between two rolls that have a narrow gap between them.

25. Drawing
The metal is pulled through a small hole in a die. Examples are copper pipe for plumbing and
various aluminium extrusion profiles for tracks, frames and rails.

26. The metal is pulled through a small hole in a dye.
Drawing
Examples are copper pipe for plumbing and
various aluminium extrusion profiles for tracks, frames and rails.
The metal is pulled through a small hole in a dye.

27. Pressing

28. Pressing
A metal sheet is pressed onto a shape or die to form an intricate shape.

29. Pressing

30. Shot Peening

31. Shot Peening
Small metal or ceramic balls called “shot” are used to bombard the surface of a metal.

32. Shot Peening
Each shot that strikes the part’s surface acts as a tiny peening hammer, imparting to the surface a small indentation or dimple.

33. Shot Peening
These dimples create residual compressive stresses at and slightly beneath the surface.
This enable the metal to better resist any fatigue and provides resistance to abrasion.

34. Hot Working
Hot working refers to plastic deformation carried out above the re-crystallization temperature.

36. Annealing

37. Annealing
Annealing is the process by which the distorted cold worked lattice structure is changed back to one which is strain free through the application of heat.

38. Metal stays in the solid state.
Slow cooling.

39. Effects of Annealing
The purpose of annealing may involve one or more of the following aims:

40. To relieve internal stresses induced by some previous treatment.
Effects of Annealing
To relieve internal stresses induced by some previous treatment.

41. To remove coarseness of grain.
Effects of Annealing
To remove coarseness of grain.

42. To soften the metal and improve machinability.
Effects of Annealing
To soften the metal and improve machinability.

43. Quenching Cooled Quickly.
To harden by quenching, a metal (usually steel or cast iron) must be heated into the austenitic crystal phase and then quickly cooled.
Cooled Quickly.

44. Quenching can be used to increase the hardness of steel.
Effects of Quenching
Quenching can be used to increase the hardness of steel.

45. Effects of Quenching
At high temperatures, alloying metals are completely dissolved in the base metal.

46. Effects of Quenching
Quenching traps the alloying metals within the crystal structure and does not allow them to precipitate out separately.

47. Tempering
Tempering in a multi-step process.

48. Tempering
First it is heated to create a solid solution of iron and carbon in a process called "austenizing". Austenizing is followed by quenching to produce a martensitic microstructure. The steel is then tempered by heating it in the range of degrees Celsius. The steel is held at that temperature until the carbon trapped in the martensite diffuses to produce either bainite, or a mixture of ferrite and cementite.

49. Tempering improves the tensile strength and hardness of the material.

50. Lab: Heat Treatment

51. Lab: Heat Treatment Data Chart Bobby Pin # of Turns Control Annealing
Quenching
Tempering

52. Lab: Heat Treatment (The Inside Story)

53. Lab: Heat Treatment (The Inside Story)
Data Chart
Heat Treatment
Diagram
Description
Annealing
Quenching
Tempering

55. Temper Colour Temperature °C Objects Pale straw 230
Planting and slotting tools
Dark straw
240
Milling cutters, drills
Brown
250
Taps, shear blades for metals
Brownish-purple
260
Punches, cups, snaps, twist drills
Purple
270
Press tools, axes
Dark purple
280
Cold chisels, sets for steel
Blue
300
Saws for wood, springs
Toughening for constructional steels

56. Hot Working
C is a strength coefficient and m is the strain rate sensitivity exponent

57. The Mystery of Katana

58. The Challenge Make a sword that would will not break in battle.
Use soft steel that would be less brittle.

59. Make a sword that would hold a sharp edge.
Make the steel very hard so that it would never dull.

60. Japanese sword makers solved the problem by hammering together layers of steel of varying hardness and welding them into a metal sandwich.

61. This sandwich of metal layers was then reheated, folded back on itself and hammered out thin again.
After this had been repeated about a dozen times, the steel consisted of thousands of paper-thin laminations of hard and soft metal.

62. When it was ground to a sharp edge the hard metal stood out and resisted dulling, while the soft steel kept the sword from breaking.
One way the

63. The hard steel forms the sword's outer shell and deadly blade, while the tough steel serves as the sword’s core.

64. University of Toronto chemistry and physics professor R. J
University of Toronto chemistry and physics professor R.J. Dwayne Miller has demonstrated that gold can get harder, not softer, when heated to high temperatures .

65. The gold was heated at rates too fast for the electrons absorbing the light energy to collide with surrounding atoms and lose energy. The electrons are further away from the atomic nucleus and there is less screening of the positive nuclear charge by these heated electrons.  The bonds between atoms actually got stronger.