1. How does the type of metal affect how much current a circuit has?

2. Electrical Circuits
Electrical circuits work because the electrons are able to flow from the positive side of the battery to the negative side.

3. Why are metals used to conduct electricity?

4. Which metal is the best conductor?
Pure silver is the best conductor of electricity, then copper, and then aluminum.
Silver is the best conductor because it has the least resistance to the flow of electricity.
According to Ohm's Law, current is equal to voltage divided by resistance.

5. Research Sources
Sources of information on electrical resistance of metals:
 "How Voltage, Current, and Resistance Relate." All About Circuits Forum RSS. N.p., n.d. Web. 01 Oct
 "Resistivities for Common Metals." Resistivities for Common Metals. N.p., n.d. Web. 01 Oct
 "TIBTECH Innovations." Conductive Materials or Metal Conductivity. N.p., n.d. Web. 01 Oct
"How to Use a Multimeter." - Learn.SFE. N.p., n.d. Web. 01 Oct. 2013

6. Hypothesis
Based on my research, I predict that the current flow will be greatest with the silver wire. I think this because the chart on page 4 shows that silver has the highest conductivity.

7. Experimental Design
piece of wire
For my experiment, I put together the circuit shown to the right. Between two of the clip wires, I inserted pieces of different types of metal (silver, copper, zinc, and aluminum). I used a multimeter to measure the amount of current in amps in the completed circuit. The information on page 7 shows how to set up a multimeter to measure current.
To get multiple trials, I moved the piece of metal to three different places in the circuit and measured the amps produced in each of the three circuits.

8. How is the amount of current in a circuit measured?
Page for explaining/ displaying:
How a specific piece of equipment works that is used in experiment
Recipe for items baked for experiment.
Survey questions if a survey was used in the experiment
Rating scale if a rating scale was used in the experiment
How is the amount of current in a circuit measured?
An ammeter is used to measure the amount of current in a circuit. The positive and negative probes from the ammeter are connected up to the circuit.

9. Type of Metal vs. Current Produced
Results
Type of Metal vs. Current Produced
Type of Metal
Current (amps)
Trial 1
Trial 2
Trial 3
Average
Zinc
0.05
0.07
0.06
Aluminum
0.12
0.14
0.11
Silver
0.22
0.25
0.23
0.24
Copper
0.19
0.17
0.18 8

11. Discussion of results
Based on my data, I can conclude that the type of metal that produced the greatest current was silver, and the type of metal that produced the lowest current was zinc. The average amperage reading for silver was 0.24 amps and the average for zinc was 0.06 amps. The averages for copper and aluminum fell in the middle range with an average of 0.12 amps for aluminum and 0.18 amps for copper. The results of my experiment support my hypothesis. The results are also in agreement with the research I read on resistance. That information said that zinc would have the greatest resistance, which would result in the lowest current flow. I was surprised to see that aluminum was the next lowest reading. I had thought that it would have a higher reading than the copper.

12. Discussion of possible sources of error
In conducting my research, I realized there were some aspects of my set-up that may have had an effect on the results. The pieces of metal I used were not all the same length and I know that the length of the metal affects its resistance. Another possible source of error was the voltage of the battery. I checked it frequently throughout the experiment, but it may have varied a little bit from trial to trial which may have affected the results.
If I were to conduct the experiment again, I would make sure to use metal pieces that were all the same size and to have a large enough supply of batteries so that the same battery was not used twice.

13. Application and implications for future research
The results of my research would be helpful to people who are doing electrical work. My research shows that silver and copper are best two metals to use. I would guess that copper is used more than silver because of its lower cost. After conducting the experiment, some other questions came to mind that I might want to research in the future. I would be interested to see if or how much the length of the metal affects current flow. I could have several pieces of the same metal that were different sizes. I would also be interested to find out how other metals, such as gold and tin, compare to the metals I studied in the experiment.

14. Extra slide could be used for:
More detailed information on sources.
Acknowledgements to people who helped with your experiment.
More pictures

15. Dependent Variable vs. Independent Variable
Results
Dependent Variable vs. Independent Variable
Independent Variable
Dependent Variable
Trial 1
Subject 1
Trial 2
Subject 2
Trial 3
Subject 3
Subject 4
Subject 5
Average