Download presentation
Presentation is loading. Please wait.
1
Virtual-Circuit Networks:
Chapter 18 Virtual-Circuit Networks: Frame Relay and ATM Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
2
Topics discussed in this section:
FRAME RELAY Frame Relay is a virtual-circuit wide-area network that was designed in response to demands for a new type of WAN in the late 1980s and early 1990s. Topics discussed in this section: Architecture Frame Relay Layers Extended Address FRADs VOFR LMI
3
Frame Relay Prior to frame relay X.25 were used as a virtual-circuit switching network. - X.25 has a low 64-kbps data rate. - X.25 has extensive flow and error control at both the data link layer and the network layer.
4
Frame Relay T1 or T3 leased lines for private WAN from public service providers. - Excessive lines (for many branches) - T1 and T3 lines assume that the user has fixed-rate data all the time (1.544 Mbps). So it is not suitable for Bursty data.
5
Frame Relay Frame Relay Features:
- Frame Relay operates at higher speed (1.544 Mbps up to Mbps). - FR operates in just the physical and Data-link layers. It can be used as a backbone network. - FR allows bursty data. - FR allows a frame size of 9000 bytes. - FR is less expensive than other traditional WANs. - FR has error detection at the data link layer only.
6
Architecture Permanent Virtual Circuits and Switched Virtual Circuits.
The frame relay WAN is used as one link in the global Internet (figure 18.1). Frame Relay is a virtual circuit network. A virtual circuit in Frame Relay is identified by a number called a data link connection identifier (DLCI).
7
Figure 18.1 Frame Relay network
8
VCIs in Frame Relay are called DLCIs.
Note VCIs in Frame Relay are called DLCIs.
9
Permanent Vs. Switched Virtual Circuits
Permanent Virtual Circuits: The connection setup is simple. Table entry is recorded for all switches by the administrator. An outgoing DLCI is given to the source, and an incoming DLCI is given to the destination. - Drawbacks: Costly , each source needs several PVC for several connections.
10
Permanent Vs. Switched Virtual Circuits
The connection is created temporary. Short connection that exists only when data are being transferred between source and destination. - Drawbacks: Requires establishing and terminating phases.
11
Switches Each switch in a Frame Relay network has a table to route frames. The table matches an incoming port-DLCI combination with an outgoing port-DLCI combination.
12
Figure 18.2 Frame Relay layers
13
Frame Relay operates only at the physical and data link layers.
Note Frame Relay operates only at the physical and data link layers.
14
Figure 18.3 Frame Relay frame
15
by the upper-layer protocols.
Note Frame Relay does not provide flow or error control; they must be provided by the upper-layer protocols.
16
Figure 18.4 Three address formats
17
Figure FRAD
18
Topics discussed in this section:
ATM Asynchronous Transfer Mode (ATM) is the cell relay protocol designed by the ATM Forum and adopted by the ITU-T. Topics discussed in this section: Design Goals Problems Architecture Switching ATM Layers
19
Figure 18.6 Multiplexing using different frame sizes
20
A cell network uses the cell as the basic unit of data exchange.
Note A cell network uses the cell as the basic unit of data exchange. A cell is defined as a small, fixed-size block of information.
21
Figure 18.7 Multiplexing using cells
22
Figure 18.8 ATM multiplexing
23
Figure 18.9 Architecture of an ATM network
24
Figure TP, VPs, and VCs
25
Figure 18.11 Example of VPs and VCs
26
Note Note that a virtual connection is defined by a pair of numbers: the VPI and the VCI.
27
Figure 18.12 Connection identifiers
28
Figure 18.13 Virtual connection identifiers in UNIs and NNIs
29
Figure An ATM cell
30
Figure 18.15 Routing with a switch
31
Figure ATM layers
32
Figure 18.17 ATM layers in endpoint devices and switches
33
Figure ATM layer
34
Figure ATM headers
35
Figure AAL1
36
Figure AAL2
37
Figure AAL3/4
38
Figure AAL5
39
Topics discussed in this section:
ATM LANs ATM is mainly a wide-area network (WAN ATM); however, the technology can be adapted to local-area networks (ATM LANs). The high data rate of the technology has attracted the attention of designers who are looking for greater and greater speeds in LANs. Topics discussed in this section: ATM LAN Architecture LAN Emulation (LANE) Client/Server Model Mixed Architecture with Client/Server
40
Figure ATM LANs
41
Figure Pure ATM LAN
42
Figure Legacy ATM LAN
43
Figure 18.27 Mixed architecture ATM LAN
44
Figure 18.28 Client and servers in a LANE
45
Figure 18.29 Client and servers in a LANE
Similar presentations
