1. Safety & EMC Standards & Block-Block Interface Definitions
Lab 2
Safety & EMC Standards & Block-Block Interface Definitions
Objectives
Introduction to Global Safety Standards
Introduction to Global EMC Standards
Determine Applicable Safety & EMC Standards
Update Product & Block Level Requirements

2. Safety Hazards & Mitigations
Lab 2
Safety Hazards & Mitigations
Deliverable 2: Safety Mitigation Slides (Team Deliverable)
You must make the product immune to these real world hazards
Single Point Device or Component Failures in Unsafe Manner
Burns from Touchable Surfaces > 40oC or High Temp Over Ambient
Electric Shock
Fire, Explosion or Shattering
Sharp Edges and Pinch Points
Abusive or Unknowing Users including Children
Find and Document All the Safety Test Standards applicable to your product to provide some safety test coverage
Develop 1 page (minimum) Mitigation plans that include any design aspects as well as brief description of test plans to verify robustness (see template slides)
Identify which blocks are affected by design aspects and add appropriate requirements to those blocks

3. Unsafe Single Point/Device Failures
Lab 2
Unsafe Single Point/Device Failures
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

4. Burns from Hot, Touchable Surfaces
Lab 2
Burns from Hot, Touchable Surfaces
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

5. Lab 2
Electric Shock
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

6. Fire, Explosion or Shattering
Lab 2
Fire, Explosion or Shattering
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

7. Sharp Edges & Pinch Points
Lab 2
Sharp Edges & Pinch Points
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

8. Abusive Or Unknowing Users
Lab 2
Abusive Or Unknowing Users
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

9. EMC Hazards & Mitigations
Lab 2
EMC Hazards & Mitigations
Deliverable 1: EMC Mitigation Slides (Team Deliverable)
You must guard your product against the following real world hazards
Electrostatic Discharges
Ambient or Stray Magnetic Field Energy
RF Electrical Field Energy
Interference of Your Product with Other Electronic Products
Poor Commercial Incoming AC Power Quality
Find and Document All the EMC Test Standards applicable to your product to provide reasonable test coverage against the above hazards (See Attached Table + EU Directive Lists)
Develop 1 page (minimum) Mitigation plans that include any design aspects as well as brief description of test plans to verify robustness (see template slides)
Identify which blocks are affected by design aspects and add appropriate requirements to those blocks

10. Med Device Directive EMC Test Summary
Lab 2
Med Device Directive EMC Test Summary
US/FCC: 47 CFR 15 - Radio Frequency Devices CFR 18 - Industrial Scientific and Medical Equipment
IEC: Electromagnetic compatibility - Requirements and tests EMC Part 3: Limits - Section 2: Limitation of harmonics in low-voltage supplies <16A EMC Part 3: Limits - Section 3: Limitation of voltage fluctuations and flicker in low-voltage supplies <16A EMC Part 3: Limits - Section 5: Limitation of voltage fluctuations and flicker in low-voltage supplies >16A EMC Part 4: Test/measurement techniques - Section 1: Overview of immunity tests EMC Part 4: Test/measurement techniques - Section 2: ESD immunity tests EMC Part 4: Test/measurement techniques - Section 3: Radiated radiofrequency immunity tests EMC Part 4: Test/measurement techniques - Section 4: Electrical fast transient/burst immunity tests EMC Part 4: Test/measurement techniques - Section 5: Surge immunity tests EMC Part 4: Test/measurement techniques - Section 6: Conducted radiofrequency immunity tests EMC Part 4: Test/measurement techniques - Section 7: General guide on harmonics measurement and instrum EMC Part 4: Test/measurement techniques - Section 8: Power frequency magnetic field immunity tests EMC Part 4: Test/ measurement techniques - Section 9: Pulsed magnetic field immunity tests EMC Part 4: Test/measurement techniques - Section 10: Damped oscillatory magnetic field immunity tests EMC Part 4: Test/measurement techniques - Section 11: Voltage dips, short interruptions and variations
CISPR: 11 Limits and methods of measurement for Industrial, Scientific and Medical Equipment Specifications for Radio Interference Measuring Apparatus and Measurement Methods Limits and Methods of Measurements of Radio Interference of Information Technology Equipment
For all applicable Stds, your Product Level Requirements should include Engineering Test Limits in addition to Certification Test Limits

11. Electro-Static Discharge
Lab 2
Electro-Static Discharge
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

12. 318-595 Lab 2 Magnetic Field Energy
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

13. RF Electric Field Energy
Lab 2
RF Electric Field Energy
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

14. Interference with Other Electronic Systems
Lab 2
Interference with Other Electronic Systems
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection

15. Poor Incoming AC Power Quality
Lab 2
Poor Incoming AC Power Quality
Mitigation Design/Devices/Materials/Packaging
Affected Blocks
Test(s) Required to Verify Protection