1. Mission Statement... The Space Wolverines will;
*Design, test, and launch a Balloon Sat into near space in order to measure infrared and visible light intensity at different altitudes, capture high altitude images of the Earth, and discover the details of the upper atmosphere.
*Test how the intensity of visible light, infrared light and other parts of the electromagnetic spectrum changes with altitude by using photo sensing diodes placed under specific filters.
*Two cameras: an infrared camera and a film camera. The infrared camera will detect heat emissions of the atmosphere and the ground below, specifically the urban areas within a 100 mile radius of the camera.

2. Design HOBO Battery Basic Stamp Photo Diodes Infrared Camera Timing
Circuit
Heater
Switches
Flight
String Tube

3. Subsystem and Overall Systems ...
Functions:
*Record the external and
internal temp.
*Record the relative humidity of the BalloonSat
*No External Batteries Required
HOBO SYSTEM

4. LIGHT INTENSITY SYSTEM
Parts:
*Three Diodes
*Each one placed
Under a different filter
(Infrared, Visible Light, and Both filters)
*Intensity of light recorded at different altitudes
by the photo diodes will be stored
on BASIC stamp.
*Data may lead to conclusions about
the amount of light absorbed by
the atmosphere
*Diodes will be connected
to a BASIC stamp.
*Powered
by one 9 volt
battery.
LIGHT INTENSITY SYSTEM
Photo Diodes

5. IMAGE CAPTURE SYSTEM Parts: *Infrared Camera
(Will be made by placing a developed unexposed E6 film over the lens)
*The E6 film will block out visible light
*Visible Light Camera
Functions of both cameras:
*Capture near simultaneous images
of the Earth
*Connected to a timing circuit.

6. Functional Block Diagram
Power (Batteries)
BASIC stamp
Timing Circuit
Film Camera
Infrared Camera
HOBO
Photo Diode w/ Infrared filter
Photo Diode w/ both filters
Photo Diode w/ Visible Light Filter
Heater
Switch 1
Switch 2
Switch 3
Functional Block Diagram

7. Parts.. Given.. 1. Digital camera 2. BASIC stamp
3. BASIC Stamp programming module
4. 9 volt batteries
5. Various on off switches
6. 3 Physical spectrum filters
7. 1 roll of E6 film for infra red filtering
8. 3 photo diodes
9. 4 metal washers
10. Plastic tube
(4) 9 Volt
Batteries
E6 Film
Digital Camera
Basic Stamp
Photodiodes
4 Metal Washers
Parts..
Given..
Foam Core
1 camera
1 HOBO
1 HOBO temperature probe Heater
Insulation
555 Timer circuit
Hot glue Aluminum Tape

8. Management Keeping on Track.. Who's in Charge of What?
Bryan: Budget/ Basic Stamp
Brandi: Design/ Management
Lee: Testing/ Design
Vu: Design/ Integration
David: Filtering the Digital Camera
Jordan: Filtering the Digital Camera
Jack: Photodiodes and Programming basic stamp

9. Balancing Object Mass Total Mass 1st Camera with Battery 129.9 g
Basic Stamp with photodiodes
49.2 g
Timing Circuit
47.5 g
Batteries (For Timing Circuit)
21.8 g
9 Vt. Battery (4)
184.0 g
HOBO with Temp. probe
35.2 g
2nd Camera with Battery
113.3 g
Heater
27.4 g
Miscellaneous:
(Form Core/ Wires/ Washers/ Plastic Tube/ Gel Packs)
> 180 g
Total Mass
788.3 g

10. (2) Subsystems Tests... (1) Drop Test... (3) Functional Test... (4)
TESTING
(1)
Drop Test...
(3)
Functional Test...
(4)
Cooler Test...
(6)
Drag Test...
(5)
Whip Test...