1. Section 19-1 & 19-2 Populations

2. Population Properties
A population is defined as a group of organisms belonging to the same species that live in the same place at the same time.
A population of deer in western Pennsylvania would be distinct from one in northern Ohio because they would rarely interact to mate.
Note: You can be the SAME SPECIES but not in the SAME Population!
Recall the Hierarchy – Organism, Population, Community, Ecosystem, Biome, Biosphere!

3. Population Properties
3 Properties: Size, Density, Dispersion! The first is population size and simply refers to the number of organisms. The second is population density which is the number of organisms found per area (land) or volume (water). Density provides more information regarding biotic or abiotic factors that can limit or support growth of a population.

4. Population Properties
The third property is dispersion which accounts for how the organisms are distributed within the population. They can be clumped for defense, behaviors, or resource use They can be uniform to reduce competition but within mating distance. They can be random Ex. Seed dispersal is dependent on wind

5. Population Dynamics
Changes in populations can be measured by comparing natality (birth rate) to mortality (death rate) within the population. The average life span or life expectancy affects population growth. It is most impacted by infant mortality followed by risk factors. Age structure diagrams can provide information on life span based on gender and % of the population with regard to reproductive capacity (fecundity).

6. Population Dynamics
Survivorship curves can be used to show the probability that members of a population will live to a certain age. Type I curves show low infant mortality and high survivorship. Type II curves show even levels of infant mortality and survivorship. Type III curves show high infant mortality and low survivorship.

7. The growth rate is a change in the population’s size and can be either positive or negative. The growth rate is impacted by migrations, births and deaths. The following equation is used to calculate growth rate. Growth rate = (births + immigration) – (deaths + emigration) Note: usually assume immigration =‘s emigration and eliminate from equation

8. Population Dynamics Birth Rate: #Birth/Total Population
Death Rate: #Death/Total Population
Growth Rate : Birth Rate – Death Rate
(If “+” = Population Increase, If “-” = Population Decrease)
New Population Change: Growth Rate * Total Population
Next Year Population: Total Population +/- New Pop Change
Ex. Total Population: Births: Deaths: 130
Birth Rate: 185/2400 = Death Rate: 130/2400 = 0.054
Growth Rate: – = (+so Increase)
New Population Change: * 2400 = 55
Next Year Population: = 2455
Note: If a VERY Large Population, they will Estimate a PerCapita value based on 1000 individuals to get the PerCpita Birth/Death/Growth Rate (using 1000 as the Total Population. Once the Growth Rate is Determined, you can Get the Population Change by multiplying this by the LARGE/Actual Population Number and then add this to determine the next year’s Population! This is how your book did it!)

9. The Exponential Model
Exponential growth occurs when populations increase by a fixed percentage over time. This results in very slow growth initially followed by rapid increases. When graphed this produces a J-shaped curve and not a linear increase. Even a small increase in population growth can be magnified under this growth model.
Lag Phase:
Bacteria are becoming "acclimated" to the new environmental conditions to which they have been introduced (pH, temperature, nutrients, etc.). There is no significant increase in numbers with time.
Exponential Growth Phase:
The living bacteria population increases rapidly with time at an exponential growth in numbers, and the growth rate increasing with time. Conditions are optimal for growth.
Stationary Phase:
With the exhaustion of nutrients and build-up of waste and secondary metabolic products, the growth rate has slowed to the point where the growth rate equals the death rate. Effectively, there is no net growth in the bacteria population.
Death Phase:
The living bacteria population decreases with time, due to a lack of nutrients and toxic metabolic by-products.

10. The Exponential Model
Exponential growth will occur if there are not many limiting factors and low rates of competition between or within populations. Species that have a high reproductive rate due to the fact that they can mature quickly, have many offspring at once and/or breed many times during the year are more likely to exhibit exponential growth. These r-selected species include bacteria, insects, rodents and annual plants.

11. The Logistic Model
Logistic growth occurs when populations increase by doubling followed by a leveling off period. This results in faster growth initially followed by a lag in growth. When graphed this produces an S-shaped curve. Growth is arithmetic and is not magnified under this model.

12. The Logistic Model
Logistic growth will occur if there are limiting factors and higher rates of competition between or within populations. Growth levels out when species reach the carrying capacity (K) which is the number of organisms the environment can support over time. K-selected species include most reptiles, birds, mammals and also perennial plants like trees and shrubs.

13. Population Regulation
There are two kinds of limiting factors that regulate population growth. Density Independent factors reduce the population regardless of it’s density. NOTE: Mainly ABIOTIC Factors! Examples of these factors include things like human exploitation, weather such as droughts or natural disasters such as floods and fires, and pollutants.

14. Population Regulation
Density Dependent factors reduce population based on density. They includes biotic things like diseases, predators, and prey availability. They also includes abiotic things like habitat space, water and light amount. (if water/light effect food production and cause competition)
Disease susceptibility increases in larger populations – spreads faster!

15. Population Regulation
Some populations fluctuate based on the presence or absence of another population. Both populations increase and decrease in cycles due to coevolution. An example is the predator Canadian lynx and its prey the snowshoe hare. Because there are limited animals in an arctic food web, these two populations are more connected than many in more temperate climates. NOTE: Lynx follows Hare, but Hare due to some other factor!

16. The Perils of Small Populations
As populations sizes decrease, the amount of genetic variability often decreases with it. A rapid reduction in population size can result in a genetic bottleneck occuring with reduces the number of alleles present in the population. If the environment changes the population may lack the alleles needed to survive and be at risk of extinction.

17. The Perils of Small Populations
As populations sizes decrease the rate of mutation has more of an influence on the gene pool. Harmful recessive alleles are expressed more often which render members of the population unfit for survival. Populations with low genetic variation may also be subject to inbreeding which also leads to low genetic variation.