1. Advisor Advanced
Release FW120

2. Overview Start up wizard - update Remote user code
Zone open too long notification – related to access
Keypad E/E counter displayed
Inverted Walk Test
PIN of the day
Service Req message after certain Interval
Demo Mode
User code entry without pressing ENTER
Option to disable all faults on keypad
Walk Test with reporting
Walk Test with arming the system
Walk Test per zone
MMS functionality

3. Start up wizard - update
Start up Wizard update – Pircam / PSTN selection
A new selection is introduced to support the Pircam.
If PIRcam is selected the PSTN communication and analogue GSM communication will not be supported.
If PSTN/ISDN/GSM is selected then the PIRcam will not be supported
Overview new selection criteria - Variant
Start-up Wizard
Variant
PSTN / ISDN / GSM
PIRcam
1. Panel language
2. Defaults
3. Time & date
4. Variant
5. Install
Installation
76%

4. Remote user code Users - Installer Set PIN code Remote PIN
Features
Configuration: Users -> Installer
Differentiate an installer connection locally or remotely
Local connection is defined by Keypad or USB
Remote connection is defined by Ethernet / GPRS
Remote PIN is to be enabled (by Enable Login) to activate the feature
Default Remote PIN code is 1278
When enabled the Remote PIN code can only be changed remotely
New SIA codes:
Remote start, success, fail: RB / RS / RU
Local start, success, fail: LB/ LS / LU
Users - Installer
Set PIN code
Remote PIN
Enable login

5. Zone open too long notification – related to access
Features
Configuration: Zone Options / Panel Timers
The Zone held open too long is a functionality for users who want to be notified if the certain zone is open (in active state) for too long. For example to trigger a Keypad’s buzzer if the door is open for longer than 30 seconds
Use Case
Zone
Others
Zone Held Open
Panel
Zone Timers
Held Open Time
Filters
Logical Function
Zone / Held open too long
Door Access with Badge, if door is open too long it can activate the output on the reader to beep until the door is closed.

6. Keypad E/E counter displayed
Features
Configuration: Panel -> LCD display options -> View E/E counter
The EE counter display is functionality for users who want to know how much time is left to enter a code to disarm the system during the Entry Time, and to know how much time is left to leave the area which is arming. Counter shall be displayed on a Keypad after choosing to arm the area(s). A r e a 1 E N T R Y 4 5 s 1
> A r e a S t i n g 4 5 s

7. Zone Inactive days / Inverted Walk Test
Features
Configuration: Installers Menu -> 8> Sys.opts Menu -> 1> Timers menu -> 4> Zn timers menu -> 7> InactiveDays
An inverted walk test is functionality for users who want to know if a zone was not triggered during certain time, e.g. user may want to set this time to 24 hours (1 day) for a door sensor. If for 24 hours nobody opens the door (or a sensor is damaged) a flag related to this zone will be set. Maximum is 127 days. In this way a damaged sensor or non-visited area could be detected
Check Counter Value: Installers Menu -> 1>Service Menu -> 2>Test menu -> 8>Inactive Days
Reset counter: Installers Menu -> 1>Service Menu -> 2>Test menu -> 8> Inactive Days 7
> I n a c t i v e D y s 1 2 1
> Z o n e 9
> R e s t T i m r

8. PIN of the day
Features
Configuration: Technical Zone -> Zone options -> Sensor type
Panel shall support Pin of the day functionality in order to have a different installer code every day. This prevents take-overs from other installers

9. Service Req message after certain Interval
Features
Configuration: Panel -> Engineer Options -> Inspection
Installer can configure a message to pop up requesting Service/Maintenance required
Inspection date
24/08/2014
Inspection Message
Service Required

10. Demo Mode Active for 15 min Displays “Demo Mode” on every keypad
Features
Configuration: Panel -> Sys.opts Menu  8.PA & Other  9.Demo mode
When the system has been programmed it can be demonstrated to the customer using demo mode. In demo mode, movement detectors (programmed as alarm types) are ignored. This allows an area or the system to be set by the normal exit route while the site is occupied.
When the panel is in demo mode the message “Demo Mode On” will be displayed on all keypads when no user is logged on. This message will only be cleared when the engineer switches off demo mode or if the engineer is logged off automatically at the end of the engineer working period. When the entry alarm sequence is demonstrated there will be no communicator activation. 9
> D e m o d Y s
<
Active for 15 min
Displays “Demo Mode” on every keypad

11. User code entry without pressing ENTER
Features
Configuration: Installer menu  8. Sys.opts Menu  7. Panel A&B opts  8. Easy unset
User code entry without confirmation is a functionality for users that allows easier disarm of the system, by using PIN code only, without having to confirm the operation with any other key. The panel will confirm the code automatically. This would allow avoiding confusion for users. 8
> E a s y u n e t Y
-> Use 1122 to disarm
-> cannot be used with Door access F

12. Option to disable all faults on keypad
Features
Configuration: Panel -> 8.Sys.opts Menu  3.LCD Dsply opts  4.Indicate fault
An option shall be added to disable all fault indications on all keypads. These should however still be logged and reported.
Selection:
Always
On Set
Disable all Faults 4
> I n d i c a t e f u l A w y s

13. Walk test with reporting
Features
The panel supports system walk test whereby all triggered sensors will be reported to the monitoring station, but no siren shall be activated.
Start Walk test with Reporting
To start walk test with reporting : 1>Service menu  2>test menu  5> Walk test menu  1>Start
Then the installer can choose between with or without reporting. W i t h r e p o n g
> Y s
< W i t h r e p o n g
> N
<
Walktest all zones (only keypad/internal sounder beep)
Walktest all zones with reporting including the keypad/internal sounder beep

14. Walk test with arming the system
Features
The panel supports system walk test whereby the system is armed via the user interface and alarms created by triggering all sensors. All sensor alarms will be reported to the monitoring station, but no siren shall be activated.
Activate Walk test with arming the system
To activate Walk Test with arming the system : 1>Service menu  2>test menu  5> Walk test menu  4>Walktest Mode W a l k t e s M o d Y
Walk test scenario is based on a standard use case -> arming the system -> tripping zones -> disarming.
Test ends when the Installer turns off the WT Mode in the menu, or the timer expires. This is to prevent the unwanted remaining in the WT Mode.

15. Walk test per zone Features Activate Walk Test per zone
The Walk test per zone is a functionality for the installers who want to verify a single zone instead of having to run a walk test for all zones.
Activate Walk Test per zone
To start Walk Test per zon : 1>Service menu  2>test menu  5> Walk test menu
3>SingleZone WT
The installer can choose between with or without reporting. W i t h r e p o n g
> Y s
< 1
> P a n e l 2 I p u t x I n p u t m b e r
> 1
< W a l k t e s i n p r o g 1
> Z o n e N d A c t i v W a l k t e s O K P r E N T R
Functionality similar to the general walk test option.

16. MMS Features Configuration MMS
Possibility to send pictures taken by a PirCam to cell phones using MMS.
Configuration MMS
Configuration of the MMS functionality:
Central Station settings: MMS Settings (Path Options GSM) :
(Settings MMS Center Belgium)