1. VRC Inspection Dylon Caudill Regional Support Manager
Inspiring students, one robot at a time

2. Key Elements of Inspection
Inspection is the starting point of your event – Thus it is VERY important!
It is key to set a good tone during inspection to carry on throughout the day.
To help set this tone, start by inviting teams to the inspection area upon check-in.

3. Key Elements of Inspection — Before the Event
Before the event read the following documents:
Go to Volunteer Resources Page, select VRC tab, select “Inspector” button:
Review Robot Inspection Checklist
Read Inspection Guide
Go to VRC page, select Official Starstruck Game Manual button:
Read Section 4, “The Robot,” in Current Game Manual
Go to the VEX Forum Official Starstruck Q&A
Review answers on Official Starstruck Q&A
Go to VEXRobotics.com VEX EDR product accessories page
Review VEX Product line to get familiar with legal parts

4. Key Elements of Inspection —
Equipment
The following equipment is suggested PER STATION:
P/N: $19.99
6-8 ft. work table (will allow 2 inspectors to share space)
Robot Inspection Checklist sheets
Ink pens, highlighter, clipboards
VRC sizing tool (can be shared)
Competition switch with cable (P/N: )
Master team list – to mark off completed Inspections
Tags (colored zip ties) or pipe cleaners to mark inspected robots
Binder or envelop to store the completed/partial checklist
P/N:
$39.99

5. Key Elements of Inspection — The Process
Always greet the team with a smile.
Start the inspection by looking over the robot and picking one item to compliment (this helps set the tone of the event).
Speak clearly to the team.
Clearly sign the Robot Inspection Checklist.
Have the team sign the Robot Inspection Checklist.
Partial Inspections – need special care and attention.

6. Key Elements of Inspection — Tips
Remind teams to bring their controller, a charged battery, and both sets of Team License plates to inspection.
If a line forms, have a volunteer start the sizing process in line or allow the teams to use a pre-sizing station.
Be sure to check off teams that have completed inspection so the remaining teams can be encouraged to get inspected.

7. Robot Inspection Checklist

8. Robot Inspection Checklist — Cont.

9. Robot Inspection Checklist — Cont.

10. Field Control Check – Software Inspection for Cortex
1. Connect Competition Switch to “Competition” port on Joystick
2. Set switches set to: “Disable”. “Autonomous”
3. Verify VEXnet Key is installed and Turn ON Joystick.
4. Verify VEXnet Key is installed and Turn ON CORTEX and wait for a link (several seconds).
5. VERIFY on BOTH VEXnet Units that the LEDs are in the following states:
___ Robot LED:…….. Mostly Solid GREEN (Blips off at 1hz rate–will vary with number of TX units) **
___ VEXnet LED…… Fast Blinking GREEN
___ Game LED………Fast Blinking YELLOW
___ Joystick LED (Joystick only) Solid Green
6. Set Competition Switch to “Enable”
___ VERIFY: Game LED on Both units is Fast Blinking GREEN.
___ VERIFY: VEXnet LED on Both units is Fast Blinking GREEN
___ VERIFY: User does NOT have control of the robot via joysticks.
7. Set Competition Switch to “Disable”
___ VERIFY: “Game” LED is Fast Blinking YELLOW
8. Set Competition Switch to “Driver”
9. Set Competition Switch to “Enable”
___ VERIFY: Game LED is Solid GREEN on both units
___ VERIFY: User DOES have control of the robot via joysticks.
10. Set Competition Switch to “Disable”
11. Turn Joystick and CORTEX OFF.

11. Regional Support Manager
Questions?
Please contact:
Dylon Caudill
Regional Support Manager
(740)

12. THANK YOU
An FAQ for this presentation will be updated monthly and posted on the Volunteer Resources page for your role.