1. Date of download: 10/25/2017
Copyright © ASME. All rights reserved.
From: Optimization of Prosthetic Foot Stiffness to Reduce Metabolic Cost and Intact Knee Loading During Below-Knee Amputee Walking: A Theoretical Study
J Biomech Eng. 2012;134(11): doi: /
Figure Legend:
Amputee musculoskeletal model. The intact leg was actuated by 25 individual Hill-type musculotendon actuators, which were grouped into 14 muscle groups based on anatomical classification with muscles in each group receiving the same excitation pattern. The 14 muscle groups consisted of GMED (anterior and posterior compartments of the gluteus medius), GMAX (gluteus maximus, adductor magnus), HAM (biceps femoris long head, medial hamstrings), BFsh (biceps femoris short head), IL (psoas, iliacus), RF (rectus femoris), VASL (vastus lateralis, vastus intermedius), VASM (vastus medialis), GAS (medial and lateral gastrocnemius), SOL (soleus, tibialis posterior), TA (tibialis anterior, peroneus tertius), PR (peroneus longus, peroneus brevis), FLXDG (flexor digitorum longus, flexor hallucis longus), and EXTDG (extensor digitorum longus, extensor hallucis longus). To improve model visualization, the smaller muscle groups that actuated the foot (PR, FLXDG, and EXTDG) are not shown. In the amputee residual leg, the same muscle groups were included except for those crossing the ankle joint (GAS, SOL, TA, PR, FLXDG, and EXTDG).

2. Date of download: 10/25/2017
Copyright © ASME. All rights reserved.
From: Optimization of Prosthetic Foot Stiffness to Reduce Metabolic Cost and Intact Knee Loading During Below-Knee Amputee Walking: A Theoretical Study
J Biomech Eng. 2012;134(11): doi: /
Figure Legend:
Schematic of the prosthetic foot model consisting of 22 rigid segments connected in series. The prosthetic foot model had 13 keel (KR1–KR13, ) and 5 heel (HR1–HR5, ) rotational degrees-of-freedom. Foot stiffness was modeled using viscoelastic elements at each rotational degree-of-freedom.

3. Date of download: 10/25/2017
Copyright © ASME. All rights reserved.
From: Optimization of Prosthetic Foot Stiffness to Reduce Metabolic Cost and Intact Knee Loading During Below-Knee Amputee Walking: A Theoretical Study
J Biomech Eng. 2012;134(11): doi: /
Figure Legend:
Comparison of simulation excitation timing (plotted below each x-axis) with group average experimental EMG data (+1 SD) of amputee subjects walking with the SLS ESAR foot plotted with respect to the residual leg gait cycle (only those muscles in which EMG data were collected are shown)

4. Date of download: 10/25/2017
Copyright © ASME. All rights reserved.
From: Optimization of Prosthetic Foot Stiffness to Reduce Metabolic Cost and Intact Knee Loading During Below-Knee Amputee Walking: A Theoretical Study
J Biomech Eng. 2012;134(11): doi: /
Figure Legend:
Intact and residual knee and hip contact forces for each walking simulation plotted with respect to the residual leg gait cycle. For each joint, forces are expressed in the distal segment reference frame and represent the force of the proximal segment on the distal segment. For example, the intact knee axial force is expressed in the intact leg tibia reference frame and represents the force of the intact femur on the intact tibia. Segment reference frames are defined to be positive in the vertical axial direction and positive in the anterior horizontal direction. The total body weight of the model was 715 N.

5. Date of download: 10/25/2017
Copyright © ASME. All rights reserved.
From: Optimization of Prosthetic Foot Stiffness to Reduce Metabolic Cost and Intact Knee Loading During Below-Knee Amputee Walking: A Theoretical Study
J Biomech Eng. 2012;134(11): doi: /
Figure Legend:
Metabolic cost profiles of the intact and residual leg muscle groups with the largest contributions plotted with respect to the residual leg gait cycle. VASL and VASM values were combined (VAS). All others had minimal values.