Presentation is loading. Please wait.

Presentation is loading. Please wait.

Magnetic Lock (280kg ) ! S pe ci fi ca ti on

Similar presentations


Presentation on theme: "Magnetic Lock (280kg ) ! S pe ci fi ca ti on"— Presentation transcript:

1 Magnetic Lock (280kg ) ! S pe ci fi ca ti on
Model Size(unit:mm) Voltage Current Holding Force Lock Signal Door Signal Door XTM-280 ( LED) Lx48.5Wx25H 12/24VDC 12V/500mA kg(600Lbs) No No Single Door XTM-280D (LED) 500Lx48.5Wx25H 12/24VDC 12V/500mAx kgx2(600Lbsx2) No No Double Door XTM-280F Lx48.5Wx25H 12/24VDC 12V/500mA kg(600Lbs) Yes No Single Door XTM-280D F Lx48.5Wx25H 12/24VDC 12V/500mA kg(600Lbs) Yes NO(B),NC(R) Single Door XTM-280 BZ Lx48.5Wx25H 12/24VDC 12V/500mAx kgx2(600Lbsx2) Yes No Double Door XTM-280D BZ Lx48.5Wx25H 12/24VDC 12V/500mAx kgx2(600Lbsx2) Yes NO(B),NC(R) Double Door XTM Lx48.5Wx25H 12/24VDC 12V/500mA kg(600Lbs) Yes No Single Door XTM Lx48.5Wx25H 12/24VDC 12V/500mAx kgx2(600Lbsx2) Yes No Double Door 24V/250mA 24V/250mAx2 24V/250mA 24V/250mA COM(Y) 24V/250mAx2 24V/250mAx2 COM(Y) 24V/250mA 24V/250mAx2 Diagram(unit:mm) Srew Hole Mounting Plate Wire Hole Location Pin M8X35 Screw Anti-magnetic Pin 38 Nut Rubber Ring Armature Plate A. The screw of armature plate should not be fi xed t oo ti ght . Proper elasticity sho uld b e gua ran tee d for th e rub ber ring so that the armature plate can adjust itself to the appropriate position. B. Check the jumper's position before connecting. Figure out it represents 12VDC or 24VDC. 25 25 250 11 500 180 11 180 43 ! Cautions: washer We create security

2 I n s t a l l a t i o n Template Door Frame Door leaf Steps Fold the plate to Close the door first, then Mark screw positions of place the upper side of armature plate and magnetic template on door frame, lock on door leaf and door while adjust the left side frame respectively. next to the door leaf. Hollow Metal Door Wooden Door Metal Surface Door Drill holes based on the Make a combination Drill a hole Drill a hole Inside:Drill a hole Outside: Diameter is16mm Outside: Diameter is 12.7mm the plastic straight pin Allen Key Rubber ring Strike the pin into the Make a combination based Place the rubber ring Use Allen key to remove armature plate slightly on the picture(add washer between armature plate the mounting plate from must be added. Wire Screw door Fix the mounting plate on Use Allen key to screw Close the door to test After all the appropriate the door frame according the lock body on the holding force. The angle procedures, the holding to the holes drilled earlier. mounting plate between armature plate force can be maximized. and magnetic lock can Finally, fix the tamper be adjusted by adding screw. or reducing washers. Door Frame Template Door leaf 36mm Door leaf marked positions. based on the picture. Inside: Diameter is 8mm Inside: Diameter is 8mm diameter is 8mm folding Setpin (to avoid movement). accordingly).The rubber ring and door leaf. lock body. We create security

3 narrow door , frameless glass door and inward opening door.
B r a c k e t I n s t a l l a t i o n Different brackets are available according to different types of doors. For example, narrow door , frameless glass door and inward opening door. L Bracket-For outward opening door ZL Bracket-For inward opening door When the door frame thickness is less than For inward opening door, ZL bracket is 42mm, L bracket is needed needed. Door Frame Inswing door Outswing door U Bracket I Bracket for armature plate For the frameless glass door. U bracket When the door frame is too thick, I bracket is needed is needed. Frame Door Leaf Frameless Armature Bracket glass door Installation Instruction Demonstration of I Bracket Demonstration of L Bracket Demonstration of ZL Bracket Demonstration of UL Bracket Installation Installation Installation Installation We create security

4 power source to V +. power source to V +.
Circuit Board Diagram A.12VDC Input: B.24VDC Input: Required power 0.5Amp(Minimum) Required power 0.25Amp(Minimum). Connect the positive(+)lead from a 12VDC Connect the positive(+)lead from a 24VDC power source to V power source to V +. Connect the ground(-)lead from a 12VDC Connect the ground(-)lead from a 24VDC power source to V power source to V -. Check jumper for 12 VDC operation Check jumper for 24 VDC operation. Time delay setting XTM-280( F ),YM-280D( F ) XTM-280(BZ),YM-280D(BZ) XTM-280,YM-280D XTM-280(LED),XTM-280D(LED) Wire Connection We create security


Download ppt "Magnetic Lock (280kg ) ! S pe ci fi ca ti on"

Similar presentations


Ads by Google