1. COLOR DOME CAMERA SDD-D425V SPECIFICATIONS MEMO USER’S MANUAL FEATURES
Power Consumption
Operating Temperature
Operating Humidity
Dimension
Weight
Power Supply
SDD-D425V
NTSC
Signal Format
Internal
Synchronization
Scanning Frequency
CVBS : 1.0Vp-p/75Ω
Video Output
0.1Lux/F1.2 (B/W : 0.002Lux/F1.2)
Min. Illumination
Electronic Shutter Speed DC
Iris Control
52dB or more (AGC Off)
S/N Ratio
OFF / BLC / HLI / D-WDR
Backlight Compensation
700TVL
Horizontal Resolution
1/3” SONY 960H Super HAD CCD II
Image Sensor
2:1 Interlace
Scanning System
976(H) x 494(V)
Effective Pixels
PAL
ON / OFF (4 Zone)
Motion Detection
ON / OFF (8 Zone)
Privacy Masking
OFF / AUTO
DPC
OFF / ON
LSC
OFF / MIRROR
Mirror
Level Selectable (0 ~31)
Sharpness
RS-485
Communication
OFF / LOW / MIDDLE / HIGH
Gain Control
AUTO / COLOR / BW / EXTERAL
Day & Night
2D-DNR
976(H) x 582(V)
15.734KHz(H), 59.94Hz(V)
15.625KHz(H), 50.00Hz(V)
1/60 ~ 1/100,000sec
1/50 ~ 1/100,000sec
Level Selectable (0 ~ 63)
D-WDR
DC Varifocal ICR Lens 2.8~12.0mm
Lens
ATW 1.2 / AWC / ANTI_CRL / MANUAL
White Balance
ENG / CHN / SPN / RUS / JPN / POR / GER / FRA
OSD
Max. 1.2W
-10°C ~ +50°C
0% ~ 80% RH
112.6(Ø) x 89.4(H)mm
Approx. 150g
DC 12V (±10%)
USER’S MANUAL
SDD-D425V
FEATURES
• 1/3” SONY 960H Super HAD CCD II
• High Resolution of 700TV Lines
• Min. Illumination of 0.1Lux at F1.2
• True Day & Night
• D-WDR : Digital Wide Dynamic Range
• 2D-DNR : Digital Noise Reduction
• DPC : Defect Pixel Compensation
• LSC : Lens Shading Compensation
• Motion Detection
• Privacy
• DC Varifocal ICR Lens 2.8~12.0mm
• 3-Axis Gimbal Bracket
• Option : RS-485 / OSD Controller
* In accordance with customers’ request and OSD controller’s option, the specifications can be fixed or changed without notice.

2. OSD CONTROL (Option- BOARD / CABLE)
PRECAUTIONS
NAME OF EACH PART
OSD CONTROL (Option- BOARD / CABLE)
Video loop-out
OSD Controller UP
DOWN R L a
• Do not install the camera in extreme temperature conditions. - Only use the camera under conditions where temperatures are between -10°Cand +50°C. Be especially careful to provide ventilation when operating under high temperatures.
• Do not install or use the camera in an environment where the humidity is high. - It can cause the image quality to be poor.
• Do not install the camera under unstable lighting conditions. - Severe lighting change or flicker can cause the camera to work improperly.
• Never use the camera close to a gas or oil leak. - It can cause malfunctions to occur.
• Do not disassemble the camera. - There are no user-serviceable parts inside it.
• Do not touch the front lens of the camera. - It is one of the most important parts of the camera. Be careful not to be stained by fingerprint.
• Never keep the camera face to strong light directly. - It can damage the image sensor.
• Do not drop the camera or subject them to physical shocks. - It can cause malfunctions to occur.
• Do not expose the camera to rain or spill beverage on it. - If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode the electronic components.
• Do not expose the camera to radioactivity. - If exposed to radioactivity the image sensor will fail.
* NOTE *
• If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur.
• Please check that the power satisfies the normal specification before connecting the camera.
Dome base
Dome cover
Lens
a. SET : Displays the menu on the screen. Press this switch to confirm status or after changing a selected item.
b. UP / DOWN : Used to move the cursor up or down in the menu screen to select a desired menu item.
c. LEFT / RIGHT : Used to move the cursor left or right in the menu screen or to change the value of the selected item.
INSTALLATION
CAMERA ASSEMBLY
1. Install the camera with the screw.
2. Adjust the camera direction.
3. Assemble the dome cover into the camera.
DIMENSION 1 2 3
CONNECTION
Video output (Connecting to monitor)
Power input (DC 12V)
Video cable (Option)
Red : RS-485+ / Yellow : RS-485- White : Motion output / Black : GND (Option)
COMPOSITION
3-AXIS GIMBAL BRACKET
• Pan rotation : Adjusting the horizontal angle. (360°)
• Tilt rotation : Adjusting the vertical angle. (100°)
• Camera rotation : Adjusting the horizontal position of the screen. (360°)
Camera
Video cable
Power cable
Screw
Cover opener
Manual