1. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
Schematic of the EHD-jet printing setup and experimental setup for EHD-jet printing

2. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
(a) Pulsating (microdripping) mode of EHD printing of wax. (b) Footprint of printed droplets from different voltages, from left 560 V to right 640 V.

3. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
Droplets dimension at different process conditions. (a) Morphology and cross section of a typical droplet (from tip III printed at 890 V). (b) Droplet volume, (c) footprint diameter, and (d) thickness for droplets printed by three different nozzles at respective working voltage range.

4. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
Experimental results indicate a unified relationship between normalize droplet diameter and electrical bond number

5. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
(a) Intersection points of the line for surface tension force and the curves for electrostatic force give the resulting droplets diameter at different voltages for tip I. (b) Comparison between droplets dimension from FEA (lines) and experimentally measured results (data points) for three different nozzles.

6. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
FEA results (dots) and fitted relations from Eq. (1) (line) of electrostatic force for tip I. (a) Relationship between electrostatic forces and voltages. (b) Relationship between electrostatic forces and droplet diameter. (c) Relationship between electrostatic forces and nozzle diameter. (d) Verification of the force prediction from Eq. (1) (circle) using experimental obtained droplet diameter (square).

7. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
(a) Schematic configuration for FEA study of the electrostatic force on the droplets. (b) Cross section plot of the nozzle, meniscus, and half ejected droplet. (c) Electrical field distribution around the nozzle tip during droplet ejection (the unit of the scale bar is V/μm).

8. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
(a) Drop-on-demand printed letter patterns. (b) Micropillar structures by printing droplet directly on the top of the previous droplets.

9. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
Effective voltage considering the dielectric substrate

10. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
(a) Schematic configuration for FEA study of electrostatic field strength and charge calculation. (b) Electrostatic field distribution along center axis for tip I at 560 V (bottom), 600 V (middle), and 640 V (top). The insertion shows the electrical field distribution around meniscus apex. (c) Charge of a single droplet for three tips at their own working range.

11. Date of download: 11/4/2017
Copyright © ASME. All rights reserved.
From: Development and Modeling of Melt Electrohydrodynamic-Jet Printing of Phase-Change Inks for High-Resolution Additive Manufacturing
J. Manuf. Sci. Eng. 2014;136(6): doi: /
Figure Legend:
(a) Typical velocity profile for droplet in-flight for tip I at 560 V, 600 V, and 640 V. (b) Impact velocity for three nozzles at different voltages. (c) Reynolds number and (d) Weber number at impact for three nozzles, tip I, tip II, and tip III.