1. PREPARING
CEMENTS

2. PREPARING CEMENTS shake powder before use
INSTRUCTIONS FOR PREPARING POWDER
shake powder before use
don‘t compress powder in the measuring scoop

3. PREPARING CEMENTS INSTRUCTIONS FOR PREPARING POWDER
Overfill the measuring scoop with powder and then remove surplus powder using the edge of the cut-off insert in the bottle neck.

4. PREPARING CEMENTS INSTRUCTIONS FOR PREPARING LIQUID
hold the bottle vertically when dosing liquid
to achieve optimum drop size, squeeze the bottle gently
any dried material must be removed from the dropper

5. PREPARING KAVITAN MIXING RATIO KAVITAN PRO
3,5g : 1g = 1 measuring scoop : 1 drop of liquid
KAVITAN PLUS
2,7g : 1g = 1 measuring scoop : 1 drop of liquid
KAVITAN CEM
1,4g : 1g = 1 measuring scoop : 2 drops of liquid

6. PREPARING KAVITAN
Place powder and liquid on a smooth disposable paper pad or a glass plate
add powder to liquid in 2 – 4 doses
mix powder and liquid using a plastic or stainless spatula at the shortest possible time (max. 30 – 45 s.)
Properly prepared cement is homogenous, flexible and non-adhesive material

7. KAVITAN PLUS PREPARATION
PREPARING KAVITAN
KAVITAN PLUS PREPARATION
MIXING TIME – 45 s
WORKING TIME – 3 min
MANIPULATING TIME min. 1:30 min
SETTING TIME min. 5 min
KAVITAN PRO PREPARATION
Doba zpracovatelnosti – od začátku mísení do začátku tuhnutí
Manipulační doba – od konce mísení do začátku tuhnutí
Doba tuhnutí – od začátku mísení do iniciálního ztuhnutí
MIXING TIME – 45 s
WORKING TIME – 3 min
MANIPULATING TIME min. 1:30 min
SETTING TIME min. 4 min

8. PREPARING KAVITAN LC mixing ratio of KAVITAN LC:
1 measuring scoop of powder
2 drops of liquid
Add powder to liquid in 2 – 4 doses

9. PREPARING KAVITAN LC mixing time max. 30 – 45 sec
density of putty, bright finish

10. PREPARING KAVITAN LC WORKING TIME Polymerization 20s
Mixing Working time
s min

11. PREPARING ADHESOR MIXING RATIO a) Base Layers and Fillings
2,30g : 0,80g = 2 measuring scoops of powder : 3 drops of liquid
MIXING TIME 2 – 2:30 min
WORKING TIME – 4:30 min
SETTING TIME 6 – 7 min

12. PREPARING ADHESOR MIXING RATIO b) Fixed Bridge Bonding
1,40g : 0,80g = 2 measuring scoops of powder : 5 drops of liquid
MIXING TIME 1 – 1:30 min
WORKING TIME – 4 min
SETTING TIME 6 – 8 min

13. PREPARING ADHESOR MIXING PROCEDURE
mix on a glass plate with stainless spatula at
23 ± 1 ºC (to prolong the working time, mixing at 20 ºC is recommended)
divide powder into 8 – 12 parts and gradually, slowly mix in to avoid lumps

14. Mistakes in preparation
PREPARING CEMENT
Mistakes in preparation
Incorrect dose of powder or liquid
Differing size of drop while measuring
Inadequate mixing of whole amount of powder into liquid
The dropper must be
kept clean

15. PREPARING CEMENTS TIPS
Before turning the bottle to the vertical position, hold it at an angle of 45º to remove air bubbles

16. STORING CEMENTS
in a cold and dry place in a well sealed inner container
at temperature 5 ºC to 25 ºC
avoid temperature higher than 25 ºC
!!! Seal the bottle and the jar carefully after withdrawing powder and liquid !!!!

17. Thank you for your attention!