2. Objectives
Describe the fasteners, anchors, and adhesives used in construction and explain their uses.
a. Identify various types of nails and cite uses for each.
b. Identify applications for staples.
c. Identify various types of screws and cite uses for each.
Building Materials, Fasteners, and Adhesives

3. WOOD-TO-WOOD DECK SCREW HEX WASHER HEAD CONCRETE SCREW
Kickoff Activity
Identify the fasteners pictured below.
FLAT MACHINE SCREW
CHISEL STAPLE
TYPE U DRIVE SCREW
MACHINE BOLT
INSIDE CHISEL STAPLE
CUT NAIL
WOOD-TO-WOOD DECK SCREW
MASONRY NAIL
HEX WASHER HEAD CONCRETE SCREW
DUPLEX NAIL
SELF-PIERCING SCREW
Building Materials, Fasteners, and Adhesives

4. Section 5.1.0
Nails are often referred to as 8-penny, 10-penny, and so on. In written form, the penny designation appears as a lowercase d.
Use the illustration to point out that the thickness (gauge) of the nail shank increases as the length increases.
Building Materials, Fasteners, and Adhesives

5. The type of staple is determined by the type of point it has.
Section 5.2.1
The type of staple is determined by the type of point it has.
Building Materials, Fasteners, and Adhesives

6. Section 5.3.0
Wood screws are commonly available in more than 20 different gauges (diameters) and lengths.
Explain that the screw gauge ranges from 0 to 24 (the higher the number, the larger the diameter).
Review with trainees the common wood screw head shapes and recesses, as illustrated in Figure 28 of the Trainee Guide.
Building Materials, Fasteners, and Adhesives

7. Section 5.3.2
Sheet-metal screws are used to fasten light-gauge steel framing members to one another and to fasten other building materials to the framing members.
Self-tapping sheet-metal screws include self-drilling and self-piercing screws.
Building Materials, Fasteners, and Adhesives

8. Machine screws have four basic head designs.
Section 5.3.3
Machine screws are used to fasten butt hinges to metal jambs or door closers to their brackets and to install lock sets.
Machine screws have four basic head designs.
Building Materials, Fasteners, and Adhesives

9. Section 5.3.4
Lag screws are heavy-duty wood screws with square- or hex-shaped heads that provide great holding power.
Lag screws are typically used to fasten heavy equipment to wood but can also be used to fasten equipment to concrete when a lag shield is used.
Building Materials, Fasteners, and Adhesives

10. Section 5.3.5
Concrete/masonry screws are used to fasten a device or fixture to concrete, CMUs, or brick without using an anchor.
To provide a close tolerance between the pilot hole and the screw threads, a specially designed carbide drill bit and installation tool are used when installing these screws.
Building Materials, Fasteners, and Adhesives

11. Section 5.3.6
Deck screws are available in a wide variety of shapes and sizes for various applications.
Fastening treated lumber and other types of wood decking to wood framing
Fastening wood decking to different gauges of metal support structures
Fastening metal decking and sheeting to different gauges and types of metal structural support members
Stress the importance of making sure that manufacturer’s recommendations are followed when selecting the proper screw for a particular application.
Building Materials, Fasteners, and Adhesives

12. Section 5.3.7
Depending on the type of drywall screw, it cuts through the gypsum board and anchors itself into wood and/or steel studs, holding the panel tight to the stud.
Explain that fine-thread and high-and-low-thread types are generally used for fastening to steel studs.
Building Materials, Fasteners, and Adhesives

13. Section 5.3.8
Drive screws are installed by hammering the screw into a drilled or punched hole of the proper size.
Drive screws are mostly used to fasten parts that will not be exposed to much pressure.
Reinforce the fact that drive screws do not require the hole to be tapped.
Building Materials, Fasteners, and Adhesives

14. Section 5.4.0
Hammer-driven pins or threaded studs use an installation tool to fasten wood or steel to concrete or CMUs without pilot holes.
Building Materials, Fasteners, and Adhesives

15. Bolts are often used to attach one unit or member to another.
Section 5.5.0
Bolts are often used to attach one unit or member to another.
Bolts differ from screws in that bolts require a nut.
Building Materials, Fasteners, and Adhesives

16. Next Lesson: Anchors and Adhesives Review Sections 5.6.0–5.10.4
Wrap Up
Using the materials named on the board, identify fasteners that can be used to fasten the materials together. Be prepared to explain why you selected the given fastener.
Next Lesson: Anchors and Adhesives Review Sections 5.6.0–5.10.4
Building Materials, Fasteners, and Adhesives