1. SUBMITTED BY EDGEFX TEAM
Automated Irrigation System using a Wireless Sensor Network and GPRS Module
SUBMITTED BY
EDGEFX TEAM

2. ABSTRACT This project is designed to water for plants regularly
The circuit comprises of sensor parts built using op-amp IC LM358.(as a comparator)
Two stiff copper wires are inserted in the soil to sense whether the soil is wet or dry.
The Microcontroller is used to control the whole system by monitoring the sensors

3. BLOCK DIAGRAM

4. HARD WARE EQUIPMENTS POWER SUPPLY BLOCK
MICROCONTROLLER (AT89S52/AT89C51)
LCD
WATER PUMP
LM358 OP-AMP
BC547 TRANSISTOR
RELAY
1N4007
LED
RESISTORS & CAPACITORS

6. EMBEDDED SYSTEMS Definition for :- EMBEDDED SYSTEMS
A combination of hardware and software which together
form a component of a larger machine.
An example of an embedded system is a microprocessor that
controls an automobile engine.
An embedded system is designed to run on its own without
human intervention, and may be required to respond to
events in real time.

7. EMBEDDED SYSTEMS

8. AT89S52 MICRO CONTROLLER Compatible with MCS®-51 Products
8K Bytes of In-System Programmable (ISP) Flash Memory
4.0V to 5.5V Operating Range
Crystal Frequency MHZ
Three-level Program Memory Lock
256 x 8-bit Internal RAM
32 Programmable I/O Lines
Three 16-bit Timer/Counters
Eight Interrupt Sources
Full Duplex UART Serial Channel
Watchdog Timer
AT89S52

9. PIN DIAGRAM OF AT89S52

10. BC547 The BC547 transistor is an NPN Epitaxial Silicon Transistor.
The BC547 transistor is a general-purpose transistor in small plastic packages.
It is used in general-purpose switching and amplification BC847/BC547 series 45 V, 100 mA NPN general-purpose transistors.
Whenever base is high, then current starts flowing through base and emitter and after that only current will pass from collector to emitter

11. LED LEDs are semiconductor devices are made out of silicon
When current passes through the LED, it emits photons as a byproduct. Normal light bulbs produce light by heating a metal filament until its white hot
LEDs present many advantages over traditional light sources including lower energy consumption, longer lifetime, improved robustness, smaller size and faster switching

12. DC- MOTOR
A DC motor is an electric motor that runs on direct current (DC) electricity. In any electric motor, operation is based on simple electromagnetism.
A simple 2-pole DC electric motor (here red represents a magnet or winding with a "North" polarization, while green represents a magnet or winding with a "South" polarization).
Every DC motor has six basic parts -- axle, rotor (a.k.a., armature), stator, commutator, field magnet(s), and brushes.

13. LM 358 ( COMPARATOR ) Internally frequency compensated for unity gain.
Large dc voltage gain: 100 Db.
Wide bandwidth (unity gain): 1 MHz (temperature compensated)
Wide power supply range:
Single supply: 3V to 32V
or dual supplies: ±1.5V to ±16V
Very low supply current drain (500 µA)-essentially independent of supply voltage.
Low input offset voltage: 2 mV
Input common-mode voltage range includes ground.
Differential input voltage range equal to the power supply voltage.

14. LM 358 PIN DIAGRAM 1 - Output 1 2 - Inverting input
3 - Non-inverting input
4 – VCC-
5 - Non-inverting input 2
6 - Inverting input 2
7 - Output 2
8 – VCC+

15. RELAY IT IS A ELECTRO MAGNETIC SWITCH
USED TO CONTROL THE ELECTRICAL DEVICES
COPPER CORE MAGNETIC FLUX PLAYS MAIN ROLE HERE

16. LIQUID CRYSTAL DISPLAY (LCD)
Most common LCDs connected to the microcontrollers are 16x2 and
20x2 displays.
This means 16 characters per line by 2 lines and 20 characters per line
by 2 lines, respectively.
The standard is referred to as HD44780U, which refers to the controller
chip which receives data from an external source (and communicates
directly with the LCD.

17. LCD BACKGROUND
If an 8-bit data bus is used the LCD will require 11 data lines
(3 control lines plus the 8 lines for the data bus)
The three control lines are referred to as EN, RS, and RW
EN=Enable (used to tell the LCD that you are sending it data)
RS=Register Select (When RS is low (0), data is treated as a command)
(When RS is High(1), data being sent is text data )
R/W=Read/Write (When RW is low (0), the data written to the LCD)
(When RW is low (0), the data reading to the LCD)

18. SOFTWARE REQUIREMENTS
PROGRAMMING LANGUAGES Embedded C , ALP (Assembly Language) COMPILERS: Keil 2.0/3.0uv DUMPING SOFT WARE: Using Micro controller flash Software we are dumping our HEX Code into Micro Controller

19. DB9 CONNECTOR
The DB9 (originally DE-9) connector is an analog 9-pin plug of the D-Sub miniature connector family (D-Sub or Sub-D).

20. MAX 232
The MAX232 is an integrated circuit that converts signals from an RS-232serial port to signals suitable for use in TTL compatible digital logic circuits.
The MAX232 is a dual driver/receiver and typically converts the RX, TX, CTS and RTS signals .
When a MAX232 IC receives a TTL level
to convert, it changes a TTL Logic 0 to
between +3 and +15V, and changes TTL
Logic 1 to between -3 to -15V, and vice
versa for converting from RS232 to TTL.

21. KEIL COMPILER WINDOW

22. BIBILOGRAPHY
The Microcontroller and Embedded systems” by Muhammad Ali Mazidi and Janice Gillispie Mazidi , Pearson Education.
ATMEL 89S52 Data Sheets.

23. THANK ‘Q’