Presentation is loading. Please wait.

Presentation is loading. Please wait.

Jan Uythoven For discussion

Published byAlexia Ami Webster Modified over 6 years ago

Similar presentations

Presentation on theme: "Jan Uythoven For discussion"— Presentation transcript:

1 Jan Uythoven For discussion
LHC TL and Sector test meeting 9/10/2014 BETS tests for MSI, TDI and TCDQ Jan Uythoven For discussion

2 Beam Energy Tracking System
BETS already existed during Run I on beam dumping system Main Bends, 4 sectors MKD, MKB and MSD (dump and dilution kickers, dump septum) Q4 quadrupole L/R 6 Run II: add similar system on MSI (injection septum) RMSI power converter has become an LHC type pc  ramp down These functions need to be defined as well together with OP, including degauss cycle to be applied TDI (Injection absorber) TCDQ (dump absorber) See also MPP meeting 19/7/2013: LHC TL & Sector tests, 9/10/2014 Jan Uythoven

3 BETS transfer function for MSI
Change of transfer function to be done locally in the tunnel Transfer function to be checked by MCS Arming sequence for BETS on MSI not needed (standalone) LHC TL & Sector tests, 9/10/2014 Jan Uythoven

4 BETS on MSI Description Proposed procedure / actions:
Works on absolute current Maskable interlock, connected to injection BIC Proposed tolerance 7 rad  1 sigma oscillation = 5e-4 tolerance on the MSI current Proposed procedure / actions: Preparation: Contact EPC and ask for current stability measurements (Hugues Thiesen) Set BETS transfer function to +/- 5e-4 relative error (Nicolas Voumard) Check we have rights to move the MSI current outside the above window MCS rights & trim rights Test: Close Injection BIS loop with MSI at nominal current. Move current of MSI outside tolerance window both ways and check each time the BETS stops injection permit Change BETSIM to 452 GeV and check injection BETS stops injection permit Check if MCS reference not correct, cannot arm injection BIS LHC TL & Sector tests, 9/10/2014 Jan Uythoven

5 BETS transfer function for TDI
Change of transfer function to be done locally in the tunnel Transfer function to be checked by MCS Arming sequence for BETS on TDI not needed (standalone) LHC TL & Sector tests, 9/10/2014 Jan Uythoven

6 BETS on TDI Description Proposed procedure / actions:
Works on gap between the two jaws To start with LVDT, 2016 on interferometry if all goes well Maskable interlock, connected to injection BIC Proposed tolerance ±1 sigma, about ± 0.6 mm Proposed procedure / actions: Preparation: Check stability of LVDT / interferometry gap measurement Set new BETS interlock window +/- 0.6 mm (Nicolas Voumard) Check energy limit used (+/- 1 GeV) Check we have rights to move the TDI (collimator role & MCS for BETS) Test: Close Injection BIS loop with TDI at nominal position. Move current TDI position outside tolerance window by moving first one jaw and then repeat with other jaw, check each time the BETS stops injection permit Set BETSIM to 452 GeV and check one cannot inject Check if MCS reference not correct, cannot arm injection BIS LHC TL & Sector tests, 9/10/2014 Jan Uythoven

7 TCDQ transfer function
Change of transfer function to be done locally in the tunnel Transfer function to be placed in MCS BETS on TCDQ needed during the arming sequence of the LBDS LHC TL & Sector tests, 9/10/2014 Jan Uythoven

8 BETS on TCDQ Description Proposed procedure / actions:
Works on absolute position of upstream and downstream side of jaw To start with LVDT, 2016 on interferometry Maskable interlock to BIS in point 6 Proposed tolerance ±1 sigma, about ± 0.XXX mm  to be determined Proposed procedure / actions: Preparation: Check stability position readings up and downstream Set new BETS interlock function +/- 0.XXX mm around ‘random’ reference function for up and downstream position (Nicolas Voumard) Check we have rights to move the TCDQ (collimator role & MCS for BETS) Test: At injection energy move TCDQ upstream outside tolerance window and check that interlock is generated. Repeat for downstream part of jaw. Repeat for both jaws at 6.5 TeV beam energy (real or BETSIM) Modify TCDQ ramp function so that requested position of one jaw is 2 x tolerance at 3 TeV, perform energy ramp (with nominal machine if available or with BETSIM) and check interlock is generated. Check if MCS reference not correct, cannot close BIS LHC TL & Sector tests, 9/10/2014 Jan Uythoven

Download ppt "Jan Uythoven For discussion"

Similar presentations

Jan Uythoven, AB/BTLHCCWG, 3 May 2006 Page 1 450 GeV Commissioning Machine Protection Needs to be commissioned to: Prevent damage with the used, higher.

Jan Uythoven, AB/BTLHCCWG, 3 May 2006 Page GeV Commissioning Machine Protection Needs to be commissioned to: Prevent damage with the used, higher.
1 Commissioning ABT Equipment in the LHC Jan Uythoven ABT TCM 13/01/2015.

1 Commissioning ABT Equipment in the LHC Jan Uythoven ABT TCM 13/01/2015.
8:16 SB 25ns dumped by RF; integrated lumi 0.6 nb-1. 9:14 BIC problem in TI8 and CMS recovering their tracker 10:09 Abort gap cleaning commissioning. 16:29.

8:16 SB 25ns dumped by RF; integrated lumi 0.6 nb-1. 9:14 BIC problem in TI8 and CMS recovering their tracker 10:09 Abort gap cleaning commissioning. 16:29.
R.Giachino / M.Albert Be/op 5 April 2015 LHC Machine check out https://indico.cern.ch/category/6386/ 1v1.

R.Giachino / M.Albert Be/op 5 April 2015 LHC Machine check out 1v1.
SECTOR TEST PREPARATION W. Bartmann, C. Bracco, J. Uythoven LIBD Meeting, 10-Feb-2015.

SECTOR TEST PREPARATION W. Bartmann, C. Bracco, J. Uythoven LIBD Meeting, 10-Feb-2015.
Mystery unable to inject: timing, BIS, SIS… 8:15 to 12: 30 Injection/LBDS studies  Fine delay adjustment of injection kickers  Synchronization of MKI.

Mystery unable to inject: timing, BIS, SIS… 8:15 to 12: 30 Injection/LBDS studies  Fine delay adjustment of injection kickers  Synchronization of MKI.
Day 26.3. ● 09:00-14:00: Collimation setup 3.5 TeV – Slowed down by losses induced by tune hump. – 48 collimators set up. – Beam dumped by ATLAS during.

Day ● 09:00-14:00: Collimation setup 3.5 TeV – Slowed down by losses induced by tune hump. – 48 collimators set up. – Beam dumped by ATLAS during.
Monday 4 th to Friday 8 th Technical stop  Coordination: Katy Foraz  Machine back to Operations Friday evening on schedule Major cryogenics intervention.

Monday 4 th to Friday 8 th Technical stop  Coordination: Katy Foraz  Machine back to Operations Friday evening on schedule Major cryogenics intervention.
1 MKBH Erratic Jan Uythoven On behalf of the ABT team (Viliam, Nicolas M., Etienne, Laurent, Francesco etc…..) MPP meeting 8/5/2015.

1 MKBH Erratic Jan Uythoven On behalf of the ABT team (Viliam, Nicolas M., Etienne, Laurent, Francesco etc…..) MPP meeting 8/5/2015.
V. Kain, G.H. Hemelsoet AB/OP1Nov 08, 2007 LHC Injection System V.Kain, G.H. Hemelsoet, AB/OP Input from: E. Carlier, B. Goddard, J. Wenninger What do.

V. Kain, G.H. Hemelsoet AB/OP1Nov 08, 2007 LHC Injection System V.Kain, G.H. Hemelsoet, AB/OP Input from: E. Carlier, B. Goddard, J. Wenninger What do.
The LHC injection systems located in points 2 and 8 are comprised of several elements common to the LHC ring and the downstream ends of the TI 2 and TI.

The LHC injection systems located in points 2 and 8 are comprised of several elements common to the LHC ring and the downstream ends of the TI 2 and TI.
What will we do for Beam Preparation: Injection and Beam Dump Jan Uythoven Thanks to M.Barnes, E.Carlier, L.Ducimetière, B.Goddard, R.Jones, Y.Kadi, V.Kain,

What will we do for Beam Preparation: Injection and Beam Dump Jan Uythoven Thanks to M.Barnes, E.Carlier, L.Ducimetière, B.Goddard, R.Jones, Y.Kadi, V.Kain,
1 Beam Dumping System MPP review 12/06/2015 Jan Uythoven for the ABT team.

1 Beam Dumping System MPP review 12/06/2015 Jan Uythoven for the ABT team.
Status of ABT beam tests preparation 9-Oct-14. Preparation of sector test without beam I MKI: – Open valves, conditioning to 55 kV, softstart – Check.

Status of ABT beam tests preparation 9-Oct-14. Preparation of sector test without beam I MKI: – Open valves, conditioning to 55 kV, softstart – Check.
LMC 27 November 2013 Status of LBDS LS1 activities and plans for 2014 reliability run Jan Uythoven for the many, many people working on the mentioned equipment.

LMC 27 November 2013 Status of LBDS LS1 activities and plans for 2014 reliability run Jan Uythoven for the many, many people working on the mentioned equipment.
Scrubbing Run: TDI, MKI and MKE interlocks Chiara Bracco, Jan Uythoven ABT/BTP Acknowledgments: T. Baer, M. Barnes, E. Carlier.

Scrubbing Run: TDI, MKI and MKE interlocks Chiara Bracco, Jan Uythoven ABT/BTP Acknowledgments: T. Baer, M. Barnes, E. Carlier.
18 July 20071 Reminder Dilution kicker system MKB is staged (2H, 2V) –Limits extracted intensity at 7 TeV to 50% of nominal –For 25ns spacing, this is.

18 July Reminder Dilution kicker system MKB is staged (2H, 2V) –Limits extracted intensity at 7 TeV to 50% of nominal –For 25ns spacing, this is.
The HiLumi LHC Design Study is included in the High Luminosity LHC project and is partly funded by the European Commission within the Framework Programme.

The HiLumi LHC Design Study is included in the High Luminosity LHC project and is partly funded by the European Commission within the Framework Programme.
1 Commissioning and Early Operation – View from Machine Protection Jan Uythoven (AB/BT) Thanks to the members of the MPWG.

1 Commissioning and Early Operation – View from Machine Protection Jan Uythoven (AB/BT) Thanks to the members of the MPWG.
Overview Extraction tests: TT40 and TT60, week 21 –controls and data, interlocking, extraction, MKE6 transfer function and energy tracking, high intensity,

Overview Extraction tests: TT40 and TT60, week 21 –controls and data, interlocking, extraction, MKE6 transfer function and energy tracking, high intensity,

Similar presentations

Ads by Google