1. SPORT EXTREME
SPORT SHEETING

2. INTRODUCTION
Sports and other regular physical exercise offer numerous benefits to the human body
However, an important factor that can substantially influence the benefits of a workout is the environment (including the surface of the gym hall or the playground) where this activity takes place
Along with sports footwear the quality of the floor covering is another critical factor for the protection of athletes’ backs, knees and ankles
All FloorworX Sport floors are engineered to ensure the best achievable conditions for ultimate athletic performance while offering maximum health and safety to athletes
All products are designed for indoor use
FloorworX vinyl sport flooring provides a durable, safe and aesthetically appealing basis for both competitive sports and amateur sporting activities

3. INTRODUCTION
Due to specialised design in combination with integrated foam backing, Sport Supreme efficiently protects athletes’ joints and cartilages during sports, training, game and competition
The patented TECH Surface™ top layer ensures durability and easy maintenance of the floor covering
Along with excellent functionality, it is renowned for optimal slip resistance which helps to prevent accidents caused by either a too low, or a too high coefficient of friction
Sport Supreme is a point elastic sport flooring, fully compliant with the requirements of EN
Areas of use include: - Multi-sports halls for team ball sports - Primary, secondary and tertiary gymnasiums - Indoor hockey grounds - Aerobic halls - Yoga studios - Gymnastics halls - Fencing halls

4. BENEFITS SPORT SUPREME_
Reduced risk of infection in case of injury due to the special bacteriostatic composition of the surface layer
2m wide rolls
Combined double-foam backing
Glassfiber reinforcement
Solvent Free
Low VOC
100% recyclable
Excellent abrasion resistance
Low maintenance cost

5. INSTALLATION
Sport Extreme should be installed in accordance with manufacturer’s recommendations
Sub-floors must be smooth, hard, clean, and dry before laying commences
Uneven, solid or suspended timber floors may need preparation to meet the required standard
In case of direct to earth concrete, it is essential that a damp proof membrane is incorporated
Sport Extreme must be allowed to relax for 24 hours in a uniform room temperature between 18°C and 27°C
All sub-floors must be tested for moisture content prior to installation
Recommended adhesive: FloorworX No. 62 acrylic adhesive

6. SUGGESTED SPECIFICATION
Supply and fix 8.0mm thick x 2.0m wide Sport Extreme vinyl sheeting, manufactured in accordance with EN and laid in FloorworX No. 62 acrylic adhesive which has been spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre on a previously prepared Class 1 sub-floor in accordance with SANS 10070, using FloorworX Self Leveller when required, including all cutting and waste
The sheeting must be rolled in both directions with an articulated 68kg three-sectional roller immediately after it has been laid into the adhesive. Joins must be butted, grooved and heat welded using the manufacturer’s welding rod, ensuring that the welding rod bonds to more than 70% of the sheet thickness

7. WARRANTY
FloorworX offers a 5 year limited warranty, subject to our terms and conditions, against defective material provided that it is installed and maintained in accordance with our recommendations

8. MAINTENANCE PREVENTIVE_
Approximately 80% of the dirt and soiling that has to be cleaned off a floor has been trafficked in from outside the building
More than 90% of that soiling can be avoided by the use of an effective entrance matting system.
When less dirt is trafficked through the entrance there will be a reduction in maintenance requirements
Regular cleaning is more cost-effective and hygienic than occasional heavy-duty cleaning
Wipe up any grease and oil spills immediately and treat stains as soon as they are observed
Black rubber wheels and rubber furniture feet can discolour the floorcovering. Hard plastic is preferred.
Always follow the manufacturer’s dosage instructions regarding the use of cleaning chemicals.

9. POST-INSTALLATION SITE CLEAN_
MAINTENANCE
POST-INSTALLATION SITE CLEAN_
Floor maintenance begins immediately after the completion of installation
The initial step is to remove any loose dirt or debris using a dry mop, broom or vacuum
Sand, construction debris and sharp-edged objects may result in irreparable damage being inflicted to the new floor
Remove any visible adhesive residue using a damp cloth. Once the adhesive has cured it will be difficult to remove
If other trades are working in the building after the installation of the flooring, the floor must be protected from subsequent damage by the use of thick paper, cardboard or hard board
No wet maintenance must take place until 72 hours (3 days) have elapsed from the time of installation (this is to ensure that the adhesive has sufficient time to cure properly and develop full bond strength)

10. MAINTENANCE INITIAL CLEAN_
Dust mop or vacuum the floor to remove loose soil and dust
Scrub the floor using a solution of FloorworX Maintain diluted 1:10 with clean water, with a rotary machine fitted with a blue pad
Remove the residue immediately after scrubbing using a wet/dry vacuum
Rinse with clean water using a flat mop and allow the floor to dry
Dry buff the floor using a rotary or high speed machine fitted with a white pad
For higher traffic areas, apply FloorworX Spray Buff in a fine stream or mist onto the floor in front of a rotary machine fitted with a red pad and work in until dry
FloorworX Spray Buff applied in this manner at the rate of 600m2 per litre assists in maintaining a smooth surface and constant level of gloss

11. MAINTENANCE REGULAR CLEANING_
Dust mop with flat mop or vacuum on a daily basis to remove dust and loose dirt
Treat spills, spots and stains immediately
Spot clean by hand with a red or white pad and a diluted solution of FloorworX Maintain, working from the outside of the mark to its centre
Dry buff or spray buff periodically, as described in Initial Clean Procedure
The frequency of dry buffing or spray buffing is dependent on the amount of foot traffic and the effectiveness of the daily cleaning regime

12. PERIODIC MAINTENANCE_
Scrub the floor using a solution of FloorworX Maintain diluted 1:10 with clean water, with a rotary machine fitted with a blue pad
Remove the residue immediately after scrubbing using a wet/dry vacuum
Rinse with clean water using a flat mop and allow the floor to dry
Dry buff the floor using a rotary or high speed machine fitted with a white pad
For higher traffic areas, apply FloorworX Spray Buff in a fine stream or mist onto the floor in front of a rotary machine fitted with a red pad and work in until dry
FloorworX Spray Buff applied in this manner at the rate of 600m2 per litre assists in maintaining a smooth surface and constant level of gloss