Presentation is loading. Please wait.

Presentation is loading. Please wait.

DQW HOM filter fabrication quality control

Published byClarence Berry Modified over 6 years ago

Similar presentations

Presentation on theme: "DQW HOM filter fabrication quality control"— Presentation transcript:

1 DQW HOM filter fabrication quality control
Qiong Wu, BNL BNL Sergey Belomestnykh, Ilan Ben-Zvi, Carlos Marques, John Skaritka, Silvia Verdú-Andrés, Binping Xiao CERN Luis Alberty, Said Atieh, Rama Calaga, Ofelia Capatina, Teddy Capelli, Federico Carra, Norbert Kuder, Raphael Leuxe, Thierry Renaglia Lancaster University/Cockcroft Institute Graeme Burt, Ben Hall, Tom Jones, Niklas Templeton SLAC Zenghai Li

2 Outline Fabrication plan Tolerance study Filter connection Summary

3 DQWCC HOM Filter Fabrication Plan
Inspect Nb stock, select pieces for filter fabrication Procure 316LN Conflat flanges and 316LN sheets from CERN Notes: Each fabrication step shall include inspection of the parts and mechanical measurements. Visual inspection of the cavity inner surfaces is required. Any imperfections shall be addressed. Cleaning of Nb parts includes ultrasonic cleaning and rinsing. Form, machine and clean filter sections from Nb sheets and bulk Fabricate cooling jacket parts Bulk BCP + rinse, trim for welding Mechanical Inspection OK not OK Weld cooling jacket Braze cooling jacket to filter Light BCP of weld regions + rinse Leak check Manufacture welding fixtures Fixture all filter parts Inspection, mechanical & RF measurements OK E-beam weld filter HOM filter is complete

4 Fabrication Plan 1 2 5 4 3 A (step 4) B (step 3)
C (step 1) 5 D (step 2) 5 Nb pieces with 4 welds Assemble sequence: 3&4, weld C, then add 5, weld D, then add 1, weld A, finally add 2, weld B. Need to carefully select the position of welding B to make sure weld D is feasible. Some (maybe all) pieces can be machined from ingot Inner blending of piece 1

5 Alignment feature An alignment feature, ie, a groove showed below, should be added to minimize the angle error between piece 1 and piece 3. Alignment holes are used for HOM coupler installation into the cavity.

6 Tolerance study Rod1P Tube1P Insertion, relative to the cavity Rod2P
hookP4 Gap0 Gap1 Insertion, relative to the cavity Evaluated the impedances with the red numbers on the left varying in ±0.5mm range, with Gap1 shifting left/right with 0.5mm. (results shown in the next page) Results showed that within this range most of the impedances will not get enhanced significantly (ie: by a factor of 50%) except the impedance of the first HOM (reasonably high though). To meet ±0.5mm range, all machining errors should be confined within ±0.1mm, all assembling errors should be confined within ±0.3mm. Additional confinement: During the final assembling to the cavity, a method should be developed to ensure Gap0 to be 4mm ±0.2mm (for two reasons: impedance change at 0.57GHz, and peak electric field on the hook). The impedances are not sensitive to the rotation of the HOM filter relative to the cavity (see the following page), however we still want to confine it within a reasonable degree.

7 Tolerance and impedance
Rod1P Rod2P Tube1P hookP4 Gap0 Gap1 Insertion, relative to the cavity Evaluate the red numbers in ±0.5mm range Tube1P and Rod2P will not affect RF performance based on S21 calculation and they are not considered in this analysis. For the ref model, Gap0=4mm, Gap1=3mm, Rod1P=-9mm (minus here means shifting left). We focus on the modes with impedances higher than 105 (Ω for longitudinal, Ω/m for transverse). All increment of impedance is ~15% or less, except for 0.57 GHz, which is still within a reasonable range. Impedance table were sent to CERN for evaluation. Impedance (circuit definition) Freq [GHz] ref. model Gap0 3.5 Gap0 4.5 Gap1 left0.5 Gap1 right0.5 Rod1P -8.5 Rod1P -9.5 0.5inner 0.5outter Mode 1.70E+05 3.69E+05 1.82E+05 2.89E+05 4.67E+05 1.17E+05 1.19E+05 L 9.34E+05 1.04E+06 8.97E+05 7.79E+05 6.97E+05 1.07E+06 8.36E+05 7.15E+05 7.72E+05 H 2.75E+06 2.59E+06 3.15E+06 3.22E+06 2.05E+06 3.77E+06 2.62E+06 2.48E+06 2.72E+06 1.69E+05 1.79E+05 1.53E+05 1.45E+05 2.00E+05 1.47E+05 1.78E+05 1.65E+05 1.75E+05 7.46E+05 7.51E+05 7.08E+05 6.81E+05 7.91E+05 7.11E+05 7.61E+05 6.98E+05 7.55E+05 V 5.35E+05 1.04E+05 5.41E+05 6.07E+05 6.41E+05 1.20E+05 3.75E+05 4.27E+05 T 1.39E+05 2.71E+05 1.57E+05 1.30E+05 6.28E+05 5.27E+05 4.22E+05 2.77E+05 7.07E+05 2.31E+05 8.15E+05 6.18E+05 5.75E+05 5.15E+05 5.62E+05 4.97E+05 5.11E+05 5.06E+05 5.02E+05 5.55E+05 5.30E+05 1.41E+05 1.56E+05 1.35E+05 1.42E+05 1.36E+05

8 Tolerance and impedance
Evaluate We use the model with gap0=3.5mm as a start All filters rotate a certain degree, as shown in the pictures. CW1: (all filters) rotate 1 degree in clockwise CCW1: rotate 1 degree in counter clockwise CW5: rotate 5 degree in clockwise CCW5: rotate 5 degree in counter clockwise Center of the HOM port All increment of impedance is ~10% or less, except for 1.5 GHz, which is still within a reasonable range. Results sent to CERN for evaluation. Clockwise for the top filter Clockwise for the bottom filters Impedance table (circuit definition) freq [GHz] Gap0 3.5 model CW1 CCW1 CW5 CCW5 1.04E+06 1.03E+06 1.09E+06 1.08E+06 1.07E+06 H 2.59E+06 2.75E+06 2.76E+06 2.78E+06 1.79E+05 1.81E+05 1.67E+05 1.65E+05 1.62E+05 7.51E+05 7.55E+05 7.09E+05 7.15E+05 7.08E+05 V 1.04E+05 2.17E+05 2.26E+05 2.28E+05 2.24E+05 T 5.27E+05 1.16E+05 2.81E+05 4.84E+05 2.75E+05 5.62E+05 6.08E+05 5.84E+05 5.93E+05 5.81E+05 1.56E+05 1.71E+05 1.63E+05 1.60E+05 Impedance table For modes with impedance higher than 105 Ω or Ω/m. L: longitudinal in Ω H: horizontal in Ω/m V: vertical in Ω/m T: transverse (a mix of longitudinal and vertical, the number showed here is the higher one of these two) in Ω/m

9 Tolerance and freq shift
In the study of the tolerances on HOM power, we focus on the two dangerous modes at MHz and MHz. The fabrication tolerances of the HOM filter and the cavity is confined in a reasonable range so that the total HOM power is <100 Watt. However there are several modes at ~600MHz that might be dangerous, an additional constraint on Gap0 (4±0.2mm) is added for risk control. Qext of the crabbing mode will not decrease to less than 50%, the coupling to the crabbing mode will extract < 2.2 Watt power to the outside load for each filter. Error in the HOM filter Qext Impedance Power [Watt] Mode Gap0 4.5 691 182.8 0.12 H 751 9308.1 61.90 L Rod1P+0.5 1375 7.63 10927 Rod1P-0.5 705 260.9 1.48 748 3084.5 25.60 721 6188.6 15.45

10 HOM window © Montesinos, Rama & Figure above shows preliminary design that fits the space limit. RF optimization is done. Optimization showed less than 0.4dB loss on S21 up to 2 GHz. Thermal study to preliminary design is done, will double check for the latest version.

11 Connection thermal analysis
300K 2K The ideal length of the connection is 220 mm. All analysis done with old window version. We have already provided the latest version after RF optimization to CERN. © F. Carra et al, CERN EDMS # Inner tube ext. diameter (SS) 17.4 mm Outer tube ext. diameter (SS) 40 mm Tube thickness 0.3 mm Copper coating 5 μm Tube length parametric Heat interceptor (80K) @26% of the length AB 1.5 W 1 W 220 Length A-B (mm)

12 Connection and constrain for the HOM filter
reference 348mm 255mm 143mm A liquid helium vessel for the HOM filter was not shown here © Capatina et, Magnetic & thermal shielding Keep the compactness For SPS prototype cavities, we managed to design the HOM coupler within the spacial constrain of the cryostat.

13 Summary The fabrication plan is prepared with assembly sequence. Alignment has been considered. The tolerance study gives reasonable machining and assembly errors after considering impedance increase and RF heating. The connection of HOM coupler to the load is designed. Thermal analysis was done for the hard line connection. All six couplers are included in the cryostat assembly.

14 BackUp

15 Step1 3 4 Slide piece 4 to piece 3 from the top, then do welding C.

16 Welding C Piece 3 Piece 4 Welding C EBW full penetration 3mm
Re-machine these places after EBW to have a smooth surface (can make these places slightly thicker before EBW)

17 Step2 1 5 Piece 3&4 after welding C
Put piece 3&4 into piece 1, place piece 5 near 3&4, ready for welding D.

18 Welding D D Piece 3&4 Welding D EBW full penetration 3mm Piece 5

19 Step 3 1 2 3&4&5 A B 3&4&5 is one piece now.
Assemble the whole filter shown on the left, do the final weldings A and B.

20 Welding A Piece 3 Piece 1 Welding A EBW full penetration 3mm
An alignment feature, ie, a groove showed below, should be added to minimize the angle error between piece 1 and piece 3.

21 Welding B Piece 1 (with 3,4,5 welded) Piece 2
The detailed configuration at here can be modified to fit a flange Welding B EBW full penetration 3mm

22 Tolerance and freq shift
F (MHz) 573.8 594.9 685.1 927.0 959.1 Mode Type L H Qext 4637 1270 1880 8602 7200 Impedance Longitudinal [Ω/cavity] 170000 25800 70100 Horizontal [Ω/m/cavity] 934000 Vertical [Ω/m/cavity] HOM Power [Watt] 0.7 3.8 <0.1 0.13 ±6 MHz HOM Power [Watt] 1.7 535.7 18.1 6.9 221.0 Harmonic of 40MHz 15th 24th 594.9MHz H field 959.1MHz H field

23 Tolerance and RF losses
Freq [MHz] Power to the load outside [Watt] Loss on Cu pins [mW] Loss on Cu gaskets [mW] Loss on Nb [mW] 573.85 1K 15.01 81.27 1.36 594.91 11.55 35.79 0.46 685.18 9.44 0.50 0.21 926.95 2.18 0.90 0.07 959.08 28.36 9.30 0.68 total: 66.53 127.76 2.79 Results are per cavity, with 3 HOM filters on each cavity.

Download ppt "DQW HOM filter fabrication quality control"

Similar presentations

MICE RF and Coupling Coil Module Outstanding Issues Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting October 26, 2004.

MICE RF and Coupling Coil Module Outstanding Issues Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting October 26, 2004.
Accelerator Science and Technology Centre Prospects of Compact Crab Cavities for LHC Peter McIntosh LHC-CC Workshop, CERN 21 st August 2008.

Accelerator Science and Technology Centre Prospects of Compact Crab Cavities for LHC Peter McIntosh LHC-CC Workshop, CERN 21 st August 2008.
All experimenters meeting – July 7, 2014 LHC Crab Cavity Overview Tom Nicol – Fermilab All Experimenter’s Meeting July 7, 2014 1 It’s a group effort –

All experimenters meeting – July 7, 2014 LHC Crab Cavity Overview Tom Nicol – Fermilab All Experimenter’s Meeting July 7, It’s a group effort –
MICE RF Cavity Design and Fabrication Update Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting October 27, 2004.

MICE RF Cavity Design and Fabrication Update Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting October 27, 2004.
RF Measurement Plan Derun Li Center for Beam Physics Lawrence Berkeley National Laboratory January 20, 2011 MICE Video Conference Meeting.

RF Measurement Plan Derun Li Center for Beam Physics Lawrence Berkeley National Laboratory January 20, 2011 MICE Video Conference Meeting.
Status of the 201 MHz Cavity and Coupling Coil Module Steve Virostek Lawrence Berkeley National Laboratory MICE Video Conference March 10, 2004.

Status of the 201 MHz Cavity and Coupling Coil Module Steve Virostek Lawrence Berkeley National Laboratory MICE Video Conference March 10, 2004.
The HiLumi LHC Design Study (a sub-system of HL-LHC) is co-funded by the European Commission within the Framework Programme 7 Capacities Specific Programme,

The HiLumi LHC Design Study (a sub-system of HL-LHC) is co-funded by the European Commission within the Framework Programme 7 Capacities Specific Programme,
Ofelia Capatina on behalf of the CERN specification team

Ofelia Capatina on behalf of the CERN specification team
SPL cryo-module conceptual design review Cavity, helium vessel and tuner assembly N. Valverde, G. Arnau, S. Atieh, I. Aviles, O. Capatina, M. Esposito,

SPL cryo-module conceptual design review Cavity, helium vessel and tuner assembly N. Valverde, G. Arnau, S. Atieh, I. Aviles, O. Capatina, M. Esposito,
201 MHz and 805 MHz Cavity Developments in MUCOOL Derun Li Center for Beam Physics Lawrence Berkeley National Laboratory Nufact 2002 Workshop, London,

201 MHz and 805 MHz Cavity Developments in MUCOOL Derun Li Center for Beam Physics Lawrence Berkeley National Laboratory Nufact 2002 Workshop, London,
ENGINEERING DESIGN AND FABRICATION OF PETS V. Soldatov¹, D. Gudkov¹, I. Syratchev², A. Samoshkin¹, G. Riddone², A. Olyunin¹, S. Atieh² 1 – JINR, Dubna,

ENGINEERING DESIGN AND FABRICATION OF PETS V. Soldatov¹, D. Gudkov¹, I. Syratchev², A. Samoshkin¹, G. Riddone², A. Olyunin¹, S. Atieh² 1 – JINR, Dubna,
MICE RFCC Module Update Allan DeMello Lawrence Berkeley National Laboratory MAP Winter Collaboration Meeting at JLab, Virginia February 28, 2011.

MICE RFCC Module Update Allan DeMello Lawrence Berkeley National Laboratory MAP Winter Collaboration Meeting at JLab, Virginia February 28, 2011.
SRF Results and Requirements Internal MLC Review Matthias Liepe1.

SRF Results and Requirements Internal MLC Review Matthias Liepe1.
RF power & FPC status 20150216 Eric Montesinos, CERN BE-RF on behalf of all people involved, great thanks to all of them !

RF power & FPC status Eric Montesinos, CERN BE-RF on behalf of all people involved, great thanks to all of them !
Zenghai Li SLAC National Accelerator Laboratory LHC-CC13 CERN, December 9-11, 2013 HOM Coupler Optimization & RF Modeling.

Zenghai Li SLAC National Accelerator Laboratory LHC-CC13 CERN, December 9-11, 2013 HOM Coupler Optimization & RF Modeling.
Cavity status; recent KEK activities 2012.05.08: Hayano (1) STF CM-1 cavities are; MHI-014: 3-rd VT:36MV/m (finished) MHI-015: 3-rd VT: 33.5 -> 18.4MV/m.

Cavity status; recent KEK activities : Hayano (1) STF CM-1 cavities are; MHI-014: 3-rd VT:36MV/m (finished) MHI-015: 3-rd VT: > 18.4MV/m.
HOM filter Length unit: mm Based on model HOM_BNLv7_6_52mm_parameter.cst Positions with “-” means moving in -x, -y or -z direction.

HOM filter Length unit: mm Based on model HOM_BNLv7_6_52mm_parameter.cst Positions with “-” means moving in -x, -y or -z direction.
Summary of AWG7 SCRF technologies Eiji Kako Wolf-Dietrich Moeller Akira Yamamoto Hitoshi Hayano Tokyo, Nov. 2013.

Summary of AWG7 SCRF technologies Eiji Kako Wolf-Dietrich Moeller Akira Yamamoto Hitoshi Hayano Tokyo, Nov
Binping Xiao On behalf of the DQWCC team 12/09/2013

Binping Xiao On behalf of the DQWCC team 12/09/2013
201 MHz Cavity Status and Test Plans at MTA MICE Collaboration Meeting at RAL, UK October 22 ~ 24, 2005 Derun Li Center for Beam Physics Lawrence Berkeley.

201 MHz Cavity Status and Test Plans at MTA MICE Collaboration Meeting at RAL, UK October 22 ~ 24, 2005 Derun Li Center for Beam Physics Lawrence Berkeley.

Similar presentations

Ads by Google