1. Hughes Gen5 Static IPs for Resellers Overview October 30, 2017

2. Gen5 Static IP Overview
Starting Monday, Oct 30, Static IP will be available in DSS for new site orders
New orders, upgrades, and downgrades are all supported
Reseller can purchase one (1) Static IPv4 IP Address per HT2000W
MSRP: $20/site/month
Notes:
Static IPs are only supported on the HT200oW
Static IPs are not supported with
Hughes HTS configurations (HT2000 with an HR4700)
Auto-deploy systems (HT2000”T” with a CCOM Ka-98H)
Technical Overview:
The Gen5 technical implementation is different from Spaceway, HN, or HX
Gen5 IPv4 Static IP Addressing uses “Port Forwarding” to reach devices on the local LAN

3. Static IP Technical Details
The Static IP Address is assigned to the internal IP addressing table of the HT2000W modem
In this example, Hughes assigns to the internal IP of the modem. Customers cannot choose static Ips.
Note: is not reachable from the remote LAN or the internet
The HT2000W uses Port Forwarding and PAT to connect to a remote device behind the HT2000W
This allows a single public IP address to be used to access up to 10 hosts on the private network behind the HT2000W.
PAT Translation Table in HT2000W Modem
Local IP Addr
Reachable IP:Port from Internet
:80
<->
:8000
:80
:8001
:3423
:8002
:8080
:8003
Gen5 GW
Remote
Internet
Echostar 17/19
HT2000W
Internet device
accesses remote PC
via :8001

4. Gen5 Static IP Overview Ordered via https://admin.myhughesnet.com/
The static IP address will be assigned only when the modem is commissioned
The modem must have completed commissioning and activation
Downloading the configuration of the Static IP can take minutes
The modem System Control Center will show when the StaticIP is configured
The System Control Center on the modem can be accessed from a local PC via:
Enter
Enter

5. From the System Control Center
From the System Control Center homepage, navigate to the top and click on System Information.
Your static IP address will be listed in the Information box shown below.
In this case, the IPv4 address is

6. Set Local Static IP Click on WiFi Settings in the left navigation box
Modem must be HT2000W
You will be presented with a login screen
Default password is “admin”
Click Login

7. Set Local Static IP (Continued)
Navigate to the left side panel. Click on LAN DHCP in the menu of options.
Next, click the COPY TO button found at the bottom of the screen. This will copy the MAC address of the intended device into the table.
Type a number between 2 to 254 in the last box of the IP address. Click Save Settings.
The local LAN will always be: /24
The modem is always
The local devices can be set between to
Up to 10 local devices can be accessed.
Then, reboot each intended remote device to port to.

8. Set Port Mapping Navigate to the left side panel.
Click on NAT in the menu of options.
Click on Port Mapping.
Assign one to three digit number between 2 to 254 (If you followed Step 3, use the same numbers) to the LAN IP Address column.
Next, enter your public and LAN port numbers.
Click on Enable.
Click on Save Settings.

9. Notes:
Consult your individual device documentation for more specific details on what ports are required for access
For help, read business-static-ip-address
Hughes Customer Support and Houston Media Systems will only support basic questions, and will not help configure equipment. The dealer/installer is responsible for this configuration on site.
Static IPs are not available in RHP until early December for any of the 11 dual polarization beams:
CHY49, NLV52, SDO64, BOI67, SDO68, NLV79, NOR81, CHY82, BIL92, DUL95, AMA104