1. Bipolar Junction Transistor Basics
BJTs B C E

2. The BJT – Bipolar Junction Transistor
Note: Normally Emitter layer is heavily doped, Base layer is lightly doped and Collector layer has Moderate doping.
The Two Types of BJT Transistors:
npn
pnp n p n p n p E C E C C C
Cross Section
Cross Section B B B B
Schematic Symbol
Schematic Symbol E E
Collector doping is usually ~ 109
Base doping is slightly higher ~ 1010 – 1011
Emitter doping is much higher ~ 1017

3. BJT Current & Voltage - EquationsIE IC IE IC -
VCE + +
VEC - E C E C - - + +
VBE
VBC IB
VEB
VCB IB - - + + B B
n p n
IE = IB + IC
VCE = -VBC + VBE
p n p
IE = IB + IC
VEC = VEB - VCB

4. Bulk-recombination Current
I co -
Inc +
VCB - p-
- Electrons
+ Holes +
Ipe
Ine n+
VBE -
Bulk-recombination Current
Figure : Current flow (components) for an n-p-n BJT in the active region.
NOTE: Most of the current is due to electrons moving from the emitter through base to the collector. Base current consists of holes crossing from the base into the emitter and of holes that recombine with electrons in the base.

5. Physical Structure
Consists of 3 alternate layers of n- and p-type semiconductor called emitter (E), base (B) and collector (C).
Majority of current enters collector, crosses base region and exits through emitter. A small current also enters base terminal, crosses base-emitter junction and exits through emitter.
Carrier transport in the active base region directly beneath the heavily doped (n+) emitter dominates i-v characteristics of BJT.

6. Ic C - - - - - - - - - - - - - - - - - n VCB + _ B p + + IB VBE _ n E n
Recombination
VCB + _
Electrons
+ Holes B p + + IB -
VBE - _ - n E IE

7. For CB Transistor IE= Ine+ Ipe Ic= Inc- Ico And Ic= - αIE + ICo
CB Current Gain, α ═ (Ic- Ico) .
(IE- 0)
For CE Trans., IC = βIb + (1+β) Ico
where β ═ α ,
1- α is CE Gain
Bulk-recombination current
ICO
Inc
Ipe
Ine
Figure: An npn transistor with variable biasing sources (common-emitter configuration).

8. Collector-Current Curves
Common-Emitter
Circuit Diagram
Collector-Current Curves
VCE IC IC + _
Active Region
VCC IB IB
Region of Operation
Description
Active
Small base current controls a large collector current
Saturation
VCE(sat) ~ 0.2V, VCE increases with IC
Cutoff
Achieved by reducing IB to 0, Ideally, IC will also be equal to 0.
VCE
Saturation Region
Cutoff Region
IB = 0

9. BJT’s have three regions of operation:
1) Active - BJT acts like an amplifier (most common use)
2) Saturation - BJT acts like a short circuit
3) Cutoff - BJT acts like an open circuit
BJT is used as a switch by switching
between these two regions.
When analyzing a DC BJT circuit, the BJT is replaced by one of the DC circuit models shown below.
DC Models for a BJT:

10. DC  and DC   = Common-emitter current gain
 = Common-base current gain
 = IC  = IC
IB IE
The relationships between the two parameters are:
 =   = 
 
Note:  and  are sometimes referred to as dc and dc because the relationships being dealt with in the BJT are DC.

11. Output characteristics: npn BJT (typical)
Note: The PE review text sometimes uses dc instead of dc. They are related as follows:
Find the approximate values of bdc and adc from the graph.
Input characteristics: npn BJT (typical)
The input characteristics look like the characteristics of a forward-biased diode. Note that VBE varies only slightly, so we often ignore these characteristics and assume:
Common approximation: VBE = Vo = 0.65 to 0.7V
Note: Two key specifications for the BJT are Bdc and Vo (or assume Vo is about 0.7 V)

12. Figure: Common-emitter characteristics displaying exaggerated secondary effects.

13. Figure: Common-emitter characteristics displaying exaggerated secondary effects.

14. Various Regions (Modes) of Operation of BJT
Active:
Most important mode of operation
Central to amplifier operation
The region where current curves are practically flat
Saturation:
Barrier potential of the junctions cancel each other out causing a virtual short (behaves as on state Switch)
Cutoff:
Current reduced to zero
Ideal transistor behaves like an open switch
* Note: There is also a mode of operation called inverse active mode, but it is rarely used.

15. BJT Trans-conductance Curve For Typical NPN Transistor 1
Collector Current:
IC =  IES eVBE/VT
Transconductance:
(slope of the curve)
gm = IC / VBE
IES = The reverse saturation current
of the B-E Junction.
VT = kT/q = 26 mV T=300oK)
 = the emission coefficient and is
usually ~1 IC
8 mA
6 mA
4 mA
2 mA
VBE
0.7 V

16. Three Possible Configurations of BJT
Biasing the transistor refers to applying voltages to the transistor to achieve certain operating conditions.
1. Common-Base Configuration (CB) : input = VEB & IE
output = VCB & IC
2. Common-Emitter Configuration (CE): input = VBE & IB
output= VCE & IC
3. Common-Collector Configuration (CC) :input = VBC & IB
(Also known as Emitter follower) output = VEC & IE

17. Circuit Diagram: NPN Transistor
Common-Base BJT Configuration + _ IC IE IB
VCB
VBE E C B
VCE
Circuit Diagram: NPN Transistor
The Table Below lists assumptions that can be made for the attributes of the common-base BJT circuit in the different regions of operation. Given for a Silicon NPN transistor.
Region of Operation IC
VCE
VBE
VCB
C-B Bias
E-B Bias
Active
IB
=VBE+VCE
~0.7V
 0V
Rev.
Fwd.
Saturation
Max
~0V
-0.7V<VCE<0
Cutoff ~0
 0V
None/Rev.

18. Common-Base (CB) Characteristics Vc- Ic (output) Characteristic Curves
Although the Common-Base configuration is not the most common configuration, it is often helpful in the understanding operation of BJT
Vc- Ic (output) Characteristic Curves IC mA
Breakdown Reg. 6
Active Region IE 4
Saturation Region
IE=2mA 2
IE=1mA
Cutoff
IE = 0
VCB
0.8V 2V 4V 6V 8V

19. Common-Collector BJT Characteristics Emitter-Current Curves
The Common-Collector biasing circuit is basically equivalent to the common-emitter biased circuit except instead of looking at IC as a function of VCE and IB we are looking at IE.
Also, since  ~ 1, and  = IC/IE that means IC~IE IE
Active Region IB
VCE
Saturation Region
Cutoff Region
IB = 0

20. n p n Transistor: Forward Active Mode Currents
Base current is given by
IC=
IB=
is forward common-emitter current gain
Emitter current is given by
VBE
IE=
Forward Collector current is
Ico is reverse saturation current
is forward common- base current gain
In this forward active operation region,
VT = kT/q =25 mV at room temperature

21. Various Biasing Circuits used for BJT
Fixed Bias Circuit
Collector to Base Bias Circuit
Potential Divider Bias Circuit

22. The Thermal Stability of Operating Point SIco
The Thermal Stability Factor : SIco
SIco = ∂Ic
∂Ico
This equation signifies that Ic Changes SIco times as fast as Ico
Differentiating the equation of Collector Current IC & rearranging the terms we can write
SIco ═ 1+β
1- β (∂Ib/∂IC)
It may be noted that Lower is the value of SIco better is the stability
Vbe, β

23. The Thermal Stability Factor : SIco
The Fixed Bias Circuit
The Thermal Stability Factor : SIco
SIco = ∂Ic
∂Ico
General Equation of SIco Comes out to be
SIco ═ β
1- β (∂Ib/∂IC)
Vbe, β RC Rb RC
Applying KVL through Base Circuit we can write, Ib Rb+ Vbe= Vcc
Diff w. r. t. IC, we get (∂Ib / ∂Ic) = 0
SIco= (1+β) is very large
Indicating high un-stability Ib

24. The Collector to Base Bias Circuit
The General Equation for Thermal Stability Factor,
SIco = ∂Ic
∂Ico
Comes out to be
SIco ═ β
1- β (∂Ib/∂IC)
Vbe, β Ic
Applying KVL through base circuit
we can write (Ib+ IC) RC + Ib Rb+ Vbe= Vcc
Diff. w. r. t. IC we get
(∂Ib / ∂Ic) = - RC / (Rb + RC)
Therefore, SIco ═ (1+ β)
1+ [βRC/(RC+ Rb)]
Which is less than (1+β), signifying better thermal stability Ib +
VBE IE -

25. The Potential Devider Bias Circuit
The General Equation for Thermal Stability Factor, SIco ═ β
1- β (∂Ib/∂IC) IC
Applying KVL through input base circuit
we can write IbRTh + IE RE+ Vbe= VTh
Therefore, IbRTh + (IC+ Ib) RE+ VBE= VTh
Diff. w. r. t. IC & rearranging we get
(∂Ib / ∂Ic) = - RE / (RTh + RE)
Therefore,
This shows that SIco is inversely proportional to RE and
It is less than (1+β), signifying better thermal stability Ib IC
Thevenin Equivalent Ckt IC Ib
Rth = R1*R2 & Vth = Vcc R2
R1+R R1+R2
Self-bias Resistor
Thevenins Equivalent Voltage

26. A Practical C E Amplifier Circuit
Input Signal Source

27. BJT Amplifier (continued)
If changes in operating currents and voltages are small enough, then IC and VCE waveforms are undistorted replicas of the input signal.
A small voltage change at the base causes a large voltage change at the collector. The voltage gain is given by:
The minus sign indicates a 1800 phase shift between input and output signals.
An 8 mV peak change in vBE gives a 5 mA change in iB and a 0.5 mA change in iC.
The 0.5 mA change in iC gives a 1.65 V change in vCE .

28. A Practical BJT Amplifier using Coupling and Bypass Capacitors
In a practical amplifier design, C1 and C3 are large coupling capacitors or dc blocking capacitors, their reactance (XC = |ZC| = 1/wC) at signal frequency is negligible. They are effective open circuits for the circuit when DC bias is considered.
C2 is a bypass capacitor. It provides a low impedance path for ac current from emitter to ground. It effectively removes RE (required for good Q-point stability) from the circuit when ac signals are considered.
AC coupling through capacitors is used to inject an ac input signal and extract the ac output signal without disturbing the DC Q-point
Capacitors provide negligible impedance at frequencies of interest and provide open circuits at dc.

29. D C Equivalent for the BJT Amplifier (Step1)
DC Equivalent Circuit
All capacitors in the original amplifier circuit are replaced by open circuits, disconnecting vI, RI, and R3 from the circuit and leaving RE intact. The the transistor Q will be replaced by its DC model.

30. A C Equivalent for the BJT Amplifier (Step 2)Ro
R1IIR2=RB
Rin
Coupling capacitor CC and Emitter bypass capacitor CE are replaced by short circuits.
DC voltage supply is replaced with short circuits, which in this case is connected to ground.

31. A C Equivalent for the BJT Amplifier (continued)
All externally connected capacitors are assumed as short circuited elements for ac signal
By combining parallel resistors into equivalent RB and R, the equivalent AC
circuit above is constructed. Here, the transistor will be replaced by its
equivalent small-signal AC model (to be developed).

32. A C Analysis of CE Amplifier
1) Determine DC operating point and
calculate small signal parameters
2) Draw the AC equivalent circuit of Amp.
• DC Voltage sources are shorted to ground
• DC Current sources are open circuited
• Large capacitors are short circuits
• Large inductors are open circuits
3) Use a Thevenin circuit (sometimes a
Norton) where necessary. Ideally the
base should be a single resistor + a single
source. Do not confuse this with the DC
Thevenin you did in step 1.
4) Replace transistor with small signal model
5) Simplify the circuit as much as necessary.
Steps to Analyze a Transistor Amplifier
6) Calculate the small signal parameters and gain etc.
Step 1
Step 2
Step 3
Step 4
Step 5
π-model used

33. Hybrid-Pi Model for the BJT
Transconductance:
Input resistance: Rin
The hybrid-pi small-signal model is the intrinsic low-frequency representation of the BJT.
The small-signal parameters are controlled by the Q-point and are independent of the geometry of the BJT.
Output resistance:
Where, VA is Early Voltage
(VA=100V for npn)

34. Hybrid Parameter ModelIi Io
Linear Two port Device Vo Vi

35. h-Parameters
h11 = hi = Input Resistance h12 = hr = Reverse Transfer Voltage Ratio h21 = hf = Forward Transfer Current Ratio h22 = ho = Output Admittance

36. Three Small signal Models of CE Transistor
The Mid-frequency small-signal models

37. An a c Equivalent Circuit
BJT Mid-frequency Analysis using the hybrid-p model:
A common emitter (CE) amplifier
The mid-frequency circuit is drawn as follows:
the coupling capacitors (Ci and Co) and the
bypass capacitor (CE) are short circuits
short the DC supply voltage (superposition)
replace the BJT with the hybrid-p model
The resulting mid-frequency circuit is shown below.
An a c Equivalent Circuit ro

38. Details of Small-Signal Analysis for Gain Av (Using Π-model)Rs Rs
From input circuit

39. C-E Amplifier Input Resistance
The input resistance, the total resistance looking into the amplifier at coupling capacitor C1, represents the total resistance presented to the AC source.

40. C-E Amplifier Output Resistance
The output resistance is the total equivalent resistance looking into the output of the amplifier at coupling capacitor C3. The input source is set to 0 and a test source is applied at the output.
But vbe=0.
since ro is usually >> RC.

41. High-Frequency Response – BJT Amplifiers
Capacitances that will affect the high-frequency response:
• Cbe, Cbc, Cce – internal capacitances
• Cwi, Cwo – wiring capacitances
• CS, CC – coupling capacitors
• CE – bypass capacitor

42. Frequency Response of Amplifiers
The voltage gain of an amplifier is typically flat over the mid-frequency range, but drops drastically for low or high frequencies. A typical frequency response is shown below.
For a CE BJT: (shown on lower right)
low-frequency drop-off is due to CE, Ci and Co
high-frequency drop-off is due to device capacitances Cp and Cm (combined to form Ctotal)
Each capacitor forms a break point (simple pole or zero) with a break frequency of the form f=1/(2pREqC), where REq is the resistance seen by the capacitor
CE usually yields the highest low-frequency break
which establishes fLow.

43. Amplifier Power Dissipation
Static power dissipation in amplifiers is determined from their DC equivalent circuits.
Total power dissipated in C-B and E-B junctions is:
where
Total power supplied is:
The difference is the power dissipated by the bias resistors.

45. Figure 4.36a Emitter follower.

46. An Emitter Follower (CC Amplifier) Amplifier
Figure Emitter follower.
Very high input Resistance
Very low out put Resistance
Unity Voltage gain with no phase shift
High current gain
Can be used for impedance matching or a circuit for providing electrical isolation

47. Figure 4.36b Emitter follower.

48. Figure 4.36c Emitter follower.

49. Capacitor Selection for the CE Amplifier
The key objective in design is to make the capacitive reactance
much smaller at the operating frequency f than the associated
resistance that must be coupled or bypassed.

50. Summary of Two-Port Parameters for CE/CS, CB/CG, CC/CD

51. A Small Signal h-parameter Model of C E - Transistor
Vce*h12

52. A Simple MOSFET Amplifier
The MOSFET is biased in the saturation region by dc voltage sources VGS and VDS = 10 V. The DC Q-point is set at (VDS, IDS) = (4.8 V, 1.56 mA) with VGS = 3.5 V.
Total gate-source voltage is:
A 1 V p-p change in vGS gives a 1.25 mA p-p change in iDS and a 4 V p-p change
in vDS. Notice the characteristic non-linear I/O relationship compared to the BJT.

53. Eber-Moll BJT Model IE IC E C RIC RIE IF IR IB B
The Eber-Moll Model for BJTs is fairly complex, but it is valid in all regions of BJT operation. The circuit diagram below shows all the components of the Eber-Moll Model: IE IC E C
RIC
RIE IF IR IB B

54. Eber-Moll BJT Model IC = FIF – IR IB = IE - IC IE = IF - RIR
R = Common-base current gain (in forward active mode)
F = Common-base current gain (in inverse active mode)
IES = Reverse-Saturation Current of B-E Junction
ICS = Reverse-Saturation Current of B-C Junction
IC = FIF – IR IB = IE - IC
IE = IF - RIR
IF = IES [exp(qVBE/kT) – 1] IR = IC [exp (qVBC/kT) – 1]
 If IES & ICS are not given, they can be determined using various
BJT parameters.

55. Small Signal BJT Equivalent Circuit
The small-signal model can be used when the BJT is in the active region. The small-signal active-region model for a CB circuit is shown below: iB iC B C r
iB
r = ( + 1) * VT IE iE E
@  = 1 and T = 25C
r = ( + 1) * 0.026 IE
Recall:
 = IC / IB

56. The Early Effect (Early Voltage) Orange = Actual IC (IC’)
Note: Common-Emitter Configuration IB
-VA
VCE
Green = Ideal IC
Orange = Actual IC (IC’)
IC’ = IC VCE + 1 VA

57. Early Effect Example
Given: The common-emitter circuit below with IB = 25A, VCC = 15V,  = 100 and VA = 80.
Find: a) The ideal collector current
b) The actual collector current
Circuit Diagram
VCE IC
= 100 = IC/IB a)
IC = 100 * IB = 100 * (25x10-6 A)
IC = 2.5 mA + _
VCC IB
b) IC’ = IC VCE + 1 = 2.5x = 2.96 mA VA
IC’ = 2.96 mA

58. Breakdown Voltage The maximum voltage that the BJT can withstand.
BVCEO = The breakdown voltage for a common-emitter biased circuit. This breakdown voltage usually ranges from ~ Volts.
BVCBO = The breakdown voltage for a common-base biased circuit. This breakdown voltage is usually much higher than BVCEO and has a minimum value of ~60 Volts.
Breakdown Voltage is Determined By:
The Base Width
Material Being Used
Doping Levels
Biasing Voltage

59. Potential-Divider Bias Circuit with Emitter Feedback
Most popular biasing circuit.
Problem: bdc can vary over a wide range for BJT’s (even with the same part number)
Solution: Adding the feedback resistor RE. How large should RE be? Let’s see.
Substituting the active region model into the circuit to the left and analyzing the circuit yields the following well known equation:
ICEO has little effect and is often neglected yielding the simpler relationship:
Voltage divider biasing circuit with emitter feedback
Replacing the input circuit by a Thevenin equivalent circuit yields:
Test for stability: For a stable Q-point w.r.t. variations in bdc choose:
Why? Because then

60. PE-Electrical Review Course - Class 4 (Transistors)
Find the Q-point for the biasing circuit shown below.
The BJT has the following specifications:
bdc = 100, rsat = 100 W (Vo not specified, so assume Vo = 0.7 V)
Example :
Example :
Repeat Example 3 if RC is changed from 1k to 2.2k.

61. PE-Electrical Review Course - Class 4 (Transistors)
Determine the Q-point for the biasing circuit shown.
The BJT has the following specifications:
bdc varies from 50 to 400, Vo = 0.7 V, ICBO = 10 nA
Solution:
Case 1: bdc = 50
Example
Case 2: bdc = Similar to Case 1 above. Results are: IC = mA, VCE = 6.14 V Summary:

62. BJT Amplifier Configurations and Relationships:
PE-Electrical Review Course - Class 4 (Transistors)
BJT Amplifier Configurations and Relationships:
Using the hybrid-p model. V CC C E B R 1 2 s i v + _ L o
Common Collector (CC) Amplifier (also called “emitter-follower”)
Note: The biasing circuit is the same for each amplifier.

63. Figure 4.16 The pnp BJT.

64. Figure 4.17 Common-emitter characteristics for a pnp BJT.

65. Figure 4.18 Common-emitter amplifier for Exercise 4.8.

66. Figure 4. 19a BJT large-signal models
Figure 4.19a BJT large-signal models. (Note: Values shown are appropriate for typical small-signal silicon devices at
a temperature of 300K.

67. Figure 4. 19b BJT large-signal models
Figure 4.19b BJT large-signal models. (Note: Values shown are appropriate for typical small-signal silicon devices at
a temperature of 300K.

68. Figure 4. 19c BJT large-signal models
Figure 4.19c BJT large-signal models. (Note: Values shown are appropriate for typical small-signal silicon devices at
a temperature of 300K.