Presentation is loading. Please wait.

Presentation is loading. Please wait.

RPDA 4AN 21/2” – 6”.

Published byBennett Mills Modified over 6 years ago

Similar presentations

Presentation on theme: "RPDA 4AN 21/2” – 6”."— Presentation transcript:

1 RPDA 4AN 21/2” – 6”

2 Modification Overview
Production of the RPDA 4AN series began in 2008. The 4AN indicates an “N” shaped pattern. The RPDA 4AN can utilize either a Type I or Type II bypass. A Lead free version (4ALF) was introduced in 2011.

3 Check Cover Removal Cover is secured by a V-band clamp and o-ring sealed. To remove clamp, loosen lock nut until the latch can be disengaged from the T-bolt. Cover has no spring load. A flat screwdriver will help pry the lid from the body.

4 Check Valve Removal Check valve modules are secured by a spacer and o-ring sealed. Remove the spacer from the body. Pull the module straight out of the body.

5 Check Disc Replacement
Remove the lock nuts and the retaining plate on the back of the module. ** Do not remove any hardware from the spring side of the module. Separate the disc retainer from the module.

6 Check Seat Removal The check seat is part of the check module and can not be removed. If the seat is damaged, the complete check module will need to be replaced.

7 Check Valve Reassembly Notes
Reassemble check modules in reverse order. Do not over tighten the lock nuts.

8 Check Valve Reassembly
Lubricate check o-rings. Push modules straight into body. Insert spacer into body. Replace access cover.

9 RV Cover Removal Cover is secured by a V-band clamp and sealed by the diaphragm. Remove sensing line. To remove clamp, loosen lock nut until the latch can be disengaged from the T-bolt. Pull cover from body.

10 RV Stem Removal Remove the RV module by grasping the diaphragm plate and pulling straight out of the body.

11 RV Seat Removal The seat is pushed into the body and o-ring sealed.
Simply pull the seat straight out of the body.

12 RV Disc Replacement Holding the module in one hand, remove the bolt and washer. Remove the seat disc.

13 Disassemble RV Module Module is spring loaded.
Holding the diaphragm plate firmly, remove the retaining bolt.

14 Disassemble RV Module Remove the bushing from the stem.
Remove the stem o-ring.

15 RV Reassembly Notes Replace and lubricate o-rings.
Reassemble in reverse order. Push module straight into body. Make sure the outer edge (bead) of the diaphragm fits into the groove on RV body.

Download ppt "RPDA 4AN 21/2” – 6”."

Similar presentations

RP-500 ½- 1. Modification Overview Production of the RP500 began in 2007 and is current. Production of the RP500 began in 2007 and is current.

RP-500 ½- 1. Modification Overview Production of the RP500 began in 2007 and is current. Production of the RP500 began in 2007 and is current.
RP4A 2½ – 6. Modification Overview Production of the RP4A series began in 2008. Production of the RP4A series began in 2008. A Lead free version (4ALF)

RP4A 2½ – 6. Modification Overview Production of the RP4A series began in Production of the RP4A series began in A Lead free version (4ALF)
RP4AN 21/2 – 6. Modification Overview Production of the RP4AN series began in 2008. Production of the RP4AN series began in 2008. The 4AN indicates an.

RP4AN 21/2 – 6. Modification Overview Production of the RP4AN series began in Production of the RP4AN series began in The 4AN indicates an.
40-200 ¾”-2”. Modification Overview  Production of the 40-200 series began in 1989 and is current.  Early models of ¾”-2” 40-200 series did not always.

¾”-2”. Modification Overview  Production of the series began in 1989 and is current.  Early models of ¾”-2” series did not always.
RPDA 4A 2½” – 6”. Modification Overview  Production of the RPDA 4A series began in 2008.  The RPDA 4A can utilize either a Type I or Type II bypass.

RPDA 4A 2½” – 6”. Modification Overview  Production of the RPDA 4A series began in  The RPDA 4A can utilize either a Type I or Type II bypass.
860 (LF), 880 ½”- 2” 860 (LF), 880 ½”- 2”. Modification Overview  Production of the ½ - 2” 860 series began in 1997 and is current.  The 880 is an “N”

860 (LF), 880 ½”- 2” 860 (LF), 880 ½”- 2”. Modification Overview  Production of the ½ - 2” 860 series began in 1997 and is current.  The 880 is an “N”
860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in 1993.  Lead free version (LF860) was introduced in 2011. Parts do not.

860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in  Lead free version (LF860) was introduced in Parts do not.
350, 350A 2½”-12”. Modification Overview  Production of the 2½ - 10” sizes began in 1998.  Production of the “A” models began in 2004. This Indicates.

350, 350A 2½”-12”. Modification Overview  Production of the 2½ - 10” sizes began in  Production of the “A” models began in This Indicates.
825, 825Y, 825YD 21/2”-10”. Modification Overview  825- (1975-1988) Cast iron body- Threaded in seats- Internal check parts are epoxy coated iron. Old.

825, 825Y, 825YD 21/2”-10”. Modification Overview  825- ( ) Cast iron body- Threaded in seats- Internal check parts are epoxy coated iron. Old.
975, 975XL ¾”-2” 975, 975XL ¾”-2”. Modification Overview  Production of the original 975 began in 1990. This version had buna-n check discs and did not.

975, 975XL ¾”-2” 975, 975XL ¾”-2”. Modification Overview  Production of the original 975 began in This version had buna-n check discs and did not.
975DA 2½”-10”. Modification Overview  Production of the 975DA began in 1993 and was discontinued in 2004.  The 975DA uses a ¾” 975XL for the bypass.

975DA 2½”-10”. Modification Overview  Production of the 975DA began in 1993 and was discontinued in  The 975DA uses a ¾” 975XL for the bypass.
825Y(YA) 3/4”-2”. Modification Overview  Production of the 825Y began in 1978 and is current.  The 825YR (1994-2006) had replaceable check seats. **

825Y(YA) 3/4”-2”. Modification Overview  Production of the 825Y began in 1978 and is current.  The 825YR ( ) had replaceable check seats. **
375AST 21/2”-10”. Modification Overview  The stainless steel (ST) series was introduced in 2011.  This version has a stainless steel body. ***(Parts.

375AST 21/2”-10”. Modification Overview  The stainless steel (ST) series was introduced in  This version has a stainless steel body. ***(Parts.
375, 375XL ¾”-1”. Modification Overview  Production of the ¾”-1” 375 began in 2004 and is current.  The lead free version 375XL was introduced in 2010.

375, 375XL ¾”-1”. Modification Overview  Production of the ¾”-1” 375 began in 2004 and is current.  The lead free version 375XL was introduced in 2010.
475, 475V 2½”-3”. Modification Overview  Production of the 2½ - 3” sizes began in 1998.  The lead free version (XL) was introduced in 2011.

475, 475V 2½”-3”. Modification Overview  Production of the 2½ - 3” sizes began in  The lead free version (XL) was introduced in 2011.
LF866 2½”-10”. Product Overview  Production of the 2½” – 10” sizes began in 2014.  The LF866 utilizes a Type 2 bypass (Model LF619 single check).

LF866 2½”-10”. Product Overview  Production of the 2½” – 10” sizes began in  The LF866 utilizes a Type 2 bypass (Model LF619 single check).
4D-200, 4D-700 2½”- 10”. Modification Overview  Production began in 2003 and was discontinued in 2009.  The 4D-700 (RPDA) uses a Type-II bypass (single.

4D-200, 4D-700 2½”- 10”. Modification Overview  Production began in 2003 and was discontinued in  The 4D-700 (RPDA) uses a Type-II bypass (single.
40-200 2½”-10”. Modification Overview  Production of the 40-200 series began in 1989 and is current.

½”-10”. Modification Overview  Production of the series began in 1989 and is current.
RPZ 2½”- 10” RPZ 2½”- 10”. Modification Overview  Production of the RPZ in sizes 2½ - 10” began in 1993 and is current.

RPZ 2½”- 10” RPZ 2½”- 10”. Modification Overview  Production of the RPZ in sizes 2½ - 10” began in 1993 and is current.
5000CIV 21/2”-10” 5000CIV 21/2”-10”. Modification Overview  Production of the 5000CIV (Watts 909RPDA) began in 1998 and is current.  The 5000CIV utilizes.

5000CIV 21/2”-10” 5000CIV 21/2”-10”. Modification Overview  Production of the 5000CIV (Watts 909RPDA) began in 1998 and is current.  The 5000CIV utilizes.

Similar presentations

Ads by Google