1. CHAPTER 4 RESONANCE CIRCUITS

2. Content Series Resonance Parallel Resonance Important Parameters
Resonance Frequency, o
Half-power frequencies, 1 and 2
Bandwidth, 
Quality Factor, Q
Application

3. Introduction
Resonance is a condition in an RLC circuit in which the capacitive and reactive reactance are equal in magnitude, thereby resulting in a purely resistive impedance.
Resonance circuits are useful for constructing filters and used in many application.

4. Series Resonance Circuit

5. At Resonance
At resonance, the impedance consists only resistive component R.
The value of current will be maximum since the total impedance is minimum.
The voltage and current are in phase.
Maximum power occurs at resonance since the power factor is unity.

6. Series Resonance Total impedance of series RLC Circuit is At resonance
The impedance now reduce to
The current at resonance

7. Resonance Frequency
Resonance frequency is the frequency where the condition of resonance occur.
Also known as center frequency.
Resonance frequency

8. Half-power Frequency
Half-power frequencies is the frequency when the magnitude of the output voltage or current is decrease by the factor of 1 / 2 from its maximum value.
Also known as cutoff frequencies.

9. Bandwidth, 
Bandwidth,  is define as the difference between the two half power frequencies.
The width of the response curve is determine by the bandwidth.

10. Current Response Curve

11. Voltage Response Curve

12. Quality Factor (Q-Factor)
The ratio of resonance frequency to the bandwidth
The “sharpness” of response curve could be measured by the quality factor, Q.

13. High-Q
It is to be a high-Q circuit when its quality factor is equal or greater than 10.
For a high-Q circuit (Q  10), the half-power frequencies are, for all practical purposes, symmetrical around the resonant frequency and can be approximated as

14. Q-Factor Vs Bandwidth
Higher value of Q, smaller the bandwidth. (Higher the selectivity)
Lower value of Q larger the bandwidth. (Lower the selectivity)

15. Maximum Power Dissipated
The average power dissipated by the RLC circuit is
The maximum power dissipated at resonance where
Thus maximum power dissipated is

16. Power Dissipated at 1 and 2
At certain frequencies, where ω = ω1 and ω2, the dissipated power is half of maximum power
Hence, ω1 and ω2 are called half-power frequencies.

17. Example 14.7 If R=2Ω, L=1mH and C=0.4 F, calculate
Resonant frequency, ωo
Half power frequencies, ω1 and ω2
Bandwidth, 
Amplitude of current at ωo, ω1 and ω2.

18. Practice Problem 14.7
A series connected circuit has R=4Ω and L=25mH. Calculate
Value of C that will produce a quality factor of 50.
Find 1 , 2 and .
Determine average power dissipated at
 = o , 1 and 2. Take Vm = 100V

19. Parallel Resonance

20. Parallel Resonance
The total admittance
Resonance occur when

21. At Resonance At resonance, the impedance consists only conductance G.
The value of current will be minimum since the total admittance is minimum.
The voltage and current are in phase.

22. Parameters in Parallel Circuit
Parallel resonant circuit has same parameters as the series resonant circuit.
Resonance frequency
Half-power frequencies

23. Parameters in Parallel Circuit
Bandwidth
Quality Factor

24. Example 14.8 If R=8kΩ, L=0.2mH and C=8F, calculateωo
Q and 
ω1 and ω2
Power dissipated at ωo, ω1 and ω2.

25. Practice Problem 14.8
A parallel resonant circuit has R=100kΩ, L=25mH and C=5nF. Calculate o
1 and 2 Q 

26. APPLICATION

27. PASSIVE FILTERS
A filter is a circuit that is designed to pass signals with desired frequencies and reject or attenuates others
A filter is a Passive Filters if it consists only passive elements which is R, L and C.
Filters that used resonant circuit
Bandpass Filter
Bandstop Filter

28. BANDPASS FILTER
A bandpass filter is designed to pass all frequencies within
ω1  ωo  ω2

29. BANDPASS FILTER
SERIES RLC CIRCUIT

30. BANDPASS FILTER
PARALLEL RLC CIRCUIT

31. BANDSTOP FILTER
A bandstop or bandreject filter is designed to stop or reject all frequencies within
ω1  ωo  ω2

32. BANDSTOP FILTER
SERIES RLC CIRCUIT

33. BANDSTOP FILTER
PARALLEL RLC CIRCUIT