1. Pengantar Teknik Elektro Telekomunikasi I

2. Standar Kompetensi
Mahasiswa mampu memahami perkembangan teknologi telekomunikasi dan pilihan profesi yang bisa diraih

3. Rujukan
Tarmo Anttalainen, Introduction to Telecommunications Network Engineering, 2003

4. KOMUNIKASI ….. ?

5. Pentingnya Komunikasi
Komunikasi adalah proses untuk saling bertukar informasi
Halangan utamanya adalah bahasa dan jarak
Tugas utama:
Pengumpulan
Pemaketan, dan
Penyaluran

6. Cara Berkomunikasi Telegraph Telephone Radio Television
Bertatap muka
Isyarat
Tulisan
Temuan Elektronik:
Telegraph
Telephone
Radio
Television
Internet (computer)

9. Perhatikan Tayangan berikut ini:
Visi teknologi

10. Sistem Telekomunikasi
Komponen Dasar:
Transmitter
Channel or medium
Receiver
Noise degrades or interferes with transmitted information.

11. Communication Systems Model
A general model of all communication systems.

12. Examples of Communication

13. Communication Systems
Transmitter
The transmitter is a collection of electronic components and circuits that converts the electrical signal into a signal suitable for transmission over a given medium.
Transmitters are made up of oscillators, amplifiers, tuned circuits and filters, modulators, frequency mixers, frequency synthesizers, and other circuits.

14. Communication Systems
Communication Channel
The communication channel is the medium by which the electronic signal is sent from one place to another.
Types of media include
Electrical conductors
Optical media
Free space
System-specific media (e.g., water is the medium for sonar).

15. Communication Systems
Receivers
A receiver is a collection of electronic components and circuits that accepts the transmitted message from the channel and converts it back into a form understandable by humans.
Receivers contain amplifiers, oscillators, mixers, tuned circuits and filters, and a demodulator or detector that recovers the original intelligence signal from the modulated carrier.

16. Communication Systems
Transceivers
A transceiver is an electronic unit that incorporates circuits that both send and receive signals.
Examples are:
Telephones
Fax machines
Handheld CB radios
Cell phones
Computer modems

17. Communication Systems
Attenuation
Signal attenuation, or degradation, exists in all media of wireless transmission. It is proportional to the square of the distance between the transmitter and receiver.

18. Communication Systems
Noise
Noise is random, undesirable electronic energy that enters the communication system via the communicating medium and interferes with the transmitted message.

19. Types of Electronic Communication
Electronic communications are classified according to whether they are
One-way (simplex) or two-way (full duplex or half duplex) transmissions
Analog or digital signals.

20. Types of Electronic Communication
Simplex
The simplest method of electronic communication is referred to as simplex.
This type of communication is one-way. Examples are:
Radio
TV broadcasting
Beeper (personal receiver)

21. Types of Electronic Communication
Full Duplex
Most electronic communication is two-way and is referred to as duplex.
When people can talk and listen simultaneously, it is called full duplex. The telephone is an example of this type of communication.

22. Types of Electronic Communication
Half Duplex
The form of two-way communication in which only one party transmits at a time is known as half duplex. Examples are:
Police, military, etc. radio transmissions
Citizen band (CB)
Family radio
Amateur radio

23. Types of Electronic Communication
Analog Signals
An analog signal is a smoothly and continuously varying voltage or current. Examples are:
Sine wave
Voice
Video (TV)

24. Types of Electronic Communication
Analog signals (a) Sine wave “tone.” (b) Voice. (c) Video (TV) signal.

25. Types of Electronic Communication
Digital Signals
Digital signals change in steps or in discrete increments.
Most digital signals use binary or two-state codes. Examples are:
Telegraph (Morse code)
Continuous wave (CW) code
Serial binary code (used in computers)

26. Types of Electronic Communication
Digital signals (a) Telegraph (Morse code). (b) Continuous-wave (CW) code. (c) Serial binary code.

27. Types of Electronic Communication
Digital Signals
Many transmissions are of signals that originate in digital form but must be converted to analog form to match the transmission medium.
Digital data over the telephone network.
Analog signals.
They are first digitized with an analog-to-digital (A/D) converter.
The data can then be transmitted and processed by computers and other digital circuits.

28. Modulation and Multiplexing
Modulation and multiplexing are electronic techniques for transmitting information efficiently from one place to another.
Modulation makes the information signal more compatible with the medium.
Multiplexing allows more than one signal to be transmitted concurrently over a single medium.

29. Modulation and Multiplexing
Multiplexing at the transmitter.

30. The Electromagnetic Spectrum
The range of electromagnetic signals encompassing all frequencies is referred to as the electromagnetic spectrum.

31. The Electromagnetic Spectrum

32. The Electromagnetic Spectrum
Frequency and Wavelength: Frequency
A signal is located on the frequency spectrum according to its frequency and wavelength.
Frequency is the number of cycles of a repetitive wave that occur in a given period of time.
A cycle consists of two voltage polarity reversals, current reversals, or electromagnetic field oscillations.
Frequency is measured in cycles per second (cps).
The unit of frequency is the hertz (Hz).

33. The Electromagnetic Spectrum
Frequency and Wavelength: Wavelength
Wavelength is the distance occupied by one cycle of a wave and is usually expressed in meters.
Wavelength is also the distance traveled by an electromagnetic wave during the time of one cycle.
The wavelength of a signal is represented by the Greek letter lambda (λ).

34. The Electromagnetic Spectrum
Frequency and wavelength. (a) One cycle. (b) One wavelength.

35. The Electromagnetic Spectrum
Frequency and Wavelength: Wavelength
Wavelength (λ) = speed of light ÷ frequency
Speed of light = 3 × 108 meters/second
Therefore:
λ = 3 × 108 / f
Example:
What is the wavelength if the frequency is 4MHz?
λ = 3 × 108 / 4 MHz
= 75 meters (m)

36. Bandwidth
Bandwidth (BW) is that portion of the electromagnetic spectrum occupied by a signal.
Channel bandwidth refers to the range of frequencies required to transmit the desired information.

37. Gain, Attenuation, and Decibels
Most circuits in electronic communication are used to manipulate signals to produce a desired result.
All signal processing circuits involve:
Gain
Attenuation

38. Gain, Attenuation, and Decibels
Gain means amplification. It is the ratio of a circuit’s output to its input.
AV = =
output
input
Vout
Vin
An amplifier has gain.

39. Gain, Attenuation, and Decibels
Most amplifiers are also power amplifiers, so the same procedure can be used to calculate power gain AP where Pin is the power input and Pout is the power output.
Power gain (Ap) = Pout / Pin
Example:
The power output of an amplifier is 6 watts (W). The power gain is 80. What is the input power?
Ap = Pout / Pin therefore Pin = Pout / Ap
Pin = 6 / 80 = W = 75 mW

40. Gain, Attenuation, and Decibels
An amplifier is cascaded when two or more stages are connected together.
The overall gain is the product of the individual circuit gains.
Example:
Three cascaded amplifiers have power gains of 5, 2, and 17. The input power is 40 mW. What is the output power?
Ap = A1 × A2 × A3 = 5 × 2 × 17 = 170
Ap = Pout / Pin therefore Pout = ApPin
Pout = 170 (40 × 10-3) = 6.8W

41. Gain, Attenuation, and Decibels
Attenuation refers to a loss introduced by a circuit or component. If the output signal is lower in amplitude than the input, the circuit has loss or attenuation.
The letter A is used to represent attenuation
Attenuation A = output/input = Vout/Vin
Circuits that introduce attenuation have a gain that is less than 1.
With cascaded circuits, the total attenuation is the product of the individual attenuations.

42. Gain, Attenuation, and Decibels
Total attenuation is the product of individual attenuations of each cascaded circuit.

43. Gain, Attenuation, and Decibels
The decibel (dB) is a unit of measure used to express the gain or loss of a circuit.
The decibel was originally created to express hearing response.
A decibel is one-tenth of a bel.
When gain and attenuation are both converted into decibels, the overall gain or attenuation of a circuit can be computed by adding individual gains or attenuations, expressed in decibels.

44. Gain, Attenuation, and Decibels
Decibels: Decibel Calculations
Voltage Gain or Attenuation
dB = 20 log Vout/ Vin
Current Gain or Attenuation
dB = 20 log Iout/ Iin
Power Gain or Attenuation
dB = 10 log Pout/ Pin

45. Gain, Attenuation, and Decibels
Decibels: Decibel Calculations
Example:
An amplifier has an input of 3 mV and an output of 5 V. What is the gain in decibels?
dB = 20 log 5/0.003
= 20 log
= 20 (3.22)
= 64.4

46. Gain, Attenuation, and Decibels
Decibels: Decibel Calculations
Example:
A filter has a power input of 50 mW and an output of 2 mW. What is the gain or attenuation?
dB = 10 log (2/50)
= 10 log (0.04)
= 10 (−1.398)
= −13.98
If the decibel figure is positive, that denotes a gain.

47. A Survey of Communications Applications
Simplex
AM and FM broadcasting
Digital radio
TV broadcasting
Digital television (DTV)
Cable television
Facsimile
Wireless remote control
Paging services
Navigation and direction-finding services
Telemetry
Radio astronomy
Surveillance
Music services
Internet radio and video

48. A Survey of Communications Applications
Family Radio service
The Internet
Wide-area networks (WANs)
Metropolitan-area networks (MANs)
Local area networks (LANs)
Duplex
Telephones
Two-way radio
Radar
Sonar
Amateur radio
Citizens radio

49. Jobs and Careers in the Communication Industry
The electronics industry is roughly divided into four major specializations:
Communications (largest in terms of people employed and the dollar value of equipment purchased)
Computers (second largest).
Industrial controls.
Instrumentation.

50. Jobs and Careers in the Communication Industry
Types of Jobs
Engineers design communication equipment and systems.
Technicians install, troubleshoot, repair, calibrate, and maintain equipment.
Engineering Technicians assist in equipment design, testing, and assembly.

51. Jobs and Careers in the Communication Industry
Types of Jobs
Technical sales representatives determine customer needs and related specifications, write proposals and sell equipment.
Technical writers generate technical documentation for equipment and systems.
Trainers develop programs, generate training and presentation materials, and conduct classroom training.