1. Radiation- and Magnet field- Tolerant Power Supply System
System Concept : Water-cooled Floating Power Supply
Monitoring & remote control
19‘‘ Power Bin
16/11/2018

2. Modular Floating Power Supply
8-12 independent potential free outputs, floating
Sensing of all outputs
DC output power 2,2kW at 250VDC per 3U box (depends on installed modules)
16/11/2018

3. Modular Floating Power Supply
CE conform EN /82 part 1
Safety in accordance with EN
Water cooled
Easy insertion / extraction locking lever and carrying handle
16/11/2018

4. Modular Floating Power Supply
Power box for 6 modules, single or dual output
Floating Range >10V (min. ca. 1,5 x Uout)
Up to 100mT Magnet field tolerant
16/11/2018

5. Radiation Tested Modules of PL 500
16/11/2018

6. Radiation Doses References
16/11/2018

7. Principle of Modular Structure
16/11/2018

8. Magnetic and Radiation Tolerant Power Module
Adjustable Values on the Regulator Board :
Output Voltage
Current Limit
max. Module Voltage (OVP)
manual trimming
16/11/2018

9. Modular Control Board Basic Board with: Clock Generation
Global Module Off if Mains Voltage too low
All Monitoring & Control Signals are fed to an (optional) plug-in monitoring board
(Already developed except the plug in board)
16/11/2018

10. Monitor and Control Board (simple)
One analog output for each voltage & current (2 * 12 lines + return)
Inhibit input for each channel (12 lines + return)
Connection to external control via 50-wire flat cable (i. g. to EMLB)
(available)
16/11/2018

11. Monitoring Board (Medium Version)
Multiplexing of input / output signals (4 address lines, 1 enable line)
Voltage, Current, Temperature & Status (4 lines + return)
Inhibit input (1 line + return)
Connection to external control via 25-wire flat cable
(Ready for board design)
16/11/2018

12. Monitoring Board (Complex Version)
Redundant micro controller system
Measurement of Voltage, Current, Temperature & Status
Inhibit & Switch Off of each channel possible (this feature must be activated with a jumper)
Connection to external control via 2-wire CAN-Bus
(Component evaluation and testing Stage)
16/11/2018

13. Monitoring Board with ELMB integrated
connects all voltage, current, temperature    and status signals to the CERN ELNB board
inhibit / switch off possible via ELNB outputs
Connection to external control via 2-wire ENLB can bus    (possible solution, still to develop)
16/11/2018

14. Available modules: Range 2-7V <30A/200W Dual Output Module
Range 2-7V <100A/500W Single Output Module
Range 5-10V <70A/500W Single Output Module
Voltage trimmable +/-20%, intern manually
16/11/2018

15. CANbus & OPC server working with „Coplex Monitoring Board“
Access to all monitoring information and control function
Can handle up to Power Supplies with max. 8 channels Power Supplies with more than 8 channels
One Address may use for “emergency”
Indicates each faulty detail
16/11/2018

16. Canbus Interface for Crate Remote Control
Wiener CANbus Interfaces can control and monitor
Power Supplies systems
voltages, currents, temperatures, failure reports
Prepared by Institute of Nuclear Physics ; Cracow - POLAND
16/11/2018

17. Canbus Interface for Crate Remote Control
CANbus Controller
Conforms CAN specification 2.0A (11-bits identifier)
9-pin male DSUB connector (CiA DS102-1 Specification)
Opto-isolated transceiver , unshielded cable can be used with at least 110 nodes for high speed (1 Mbaud) bus
16/11/2018
Prepared by Institute of Nuclear Physics ; Cracow - POLAND

18. Canbus Interface for Crate Remote Control
Wiener CANbus Interface Protocol
COB ID mapping doesn’t directly correspond to the CAL/CMS priority definition
CANOpen protocol is not supported
No NMT, SDO, SYNC, TimeStamp, Nodeguard messages
It doesn’t conform Minimal Functionality Device Specification (CiA 301 profile)
16/11/2018
Prepared by Institute of Nuclear Physics ; Cracow - POLAND

19. CANbus Integration, Interface to SCADA
via OPC standard
CANbus Interface
PVSSII Application
OPC Client I/F
Commercial CanBus Interface PCI Card with Custom OPC Server
PVSSII Application
OPC Client I/F
CANBus
Wiener
Device
Wiener
Device
Wiener
Device
Wiener
Device
Known devices only
16/11/2018
Prepared by Institute of Nuclear Physics ; Cracow - POLAND

20. Custom OPC Server Features:
Supports only one type of devices (i.E. WIENER only)
Is dedicated to one type of PCI CAN I/F card (API library) – presently Kvaser Card
Needs to be redesigned if one of above changes
16/11/2018
Prepared by Institute of Nuclear Physics ; Cracow - POLAND

21. Custom OPC Server Architecture: OPC Data Access Server Interfaces
KVASER PCI/CAN driver with
Application Program Interface
for C/C++
OPC Data Access
Server Interfaces
Process Data Access Functionality
Configuration, Initialization
KVASER PCI/CAN API calls
OPC Toolkit
Custom software
KVASER Firmware
DCOM
CANbus
16/11/2018
Prepared by Institute of Nuclear Physics ; Cracow - POLAND

22. Functional Blocks of the OPC Server Kit
Initializer of the driver and devices
Process data access queues handling
Two separate threads: listening and transmitting (for each CAN port)
Process data to/from CAN messages mapping
ERROR (and WARNING) messages logger
16/11/2018
Prepared by Institute of Nuclear Physics ; Cracow - POLAND

23. Network configuration example (variable namespace)
16/11/2018
Prepared by Institute of Nuclear Physics ; Cracow - POLAND

24. 19”Power Bins for PL 500 / 6021 High current outputs < 8 Channels
16/11/2018

25. Connector side of PL 500 / 6021 Medium current outputs < 12 Channels
16/11/2018