Download presentation
Presentation is loading. Please wait.
Published byGwenda Newton Modified over 6 years ago
1
2018 SHADE Conference “Fundamentals (Keys) of Basic Irrigation Design”
2
Fundamentals of Basic Irrigation Design
1. Keys to a Successful Project 2. Key Terms Review 3. Key Concepts 4. Keys to Efficient Design 5. Spare Keys
3
Keys to a Successful Project
Design Installation Maintenance
4
Key Irrigation Terms Flow - Gallons Per Minute (GPM)
Flow - Gallons Per Hour (GPH) Pressure – Pounds Per Square Inch (PSI) Velocity – Feet Per Second (FPS) Friction Loss - Pressure loss as water moves through irrigation system components
5
Key Irrigation Terms Precipitation Rate – Inches Per Hour (PR)
Matched Precipitation Rate (MPR) Head-to-Head Coverage Evapotranspiration (ET) Distribution Uniformity (DU) Static & Dynamic Water Pressure
6
Key Concepts A sprinkler system has to have enough water and pressure to make it work properly. Where do the water and pressure come from?
7
Key Concepts
8
Key Concepts Gravity – for each foot of elevation change, psi of pressure is gained (or lost). At the base of a 100’ water tower, how much water pressure would you have? Pressure is lost as water moves through the components of an irrigation system.
9
Key Concepts
10
Keys For Safe Flow The maximum allowable loss through the meter should be less than 10 percent of the inlet pressure at the meter. The maximum flow (gallons per minute) through the meter should be 75% of the maximum safe flow through the meter. The velocity of the water flow (ft/s) through the service line supplying the meter should not exceed approximately 7 feet per second for metal pipe and 5 feet per second for plastic pipes. “Foundations of Landscape Irrigation Design” - IA
11
Key Concepts
12
Key Concepts
13
Key Concepts
14
Key Concepts Schedule 40 Mainlines Class 200 Laterals
Class 200 Pipe Sizing 0-5 GPM /2” 6-10 GPM /4” 11-16 GPM ”
15
Key Concepts
16
Key Concepts
17
Key Concepts
18
Key Concepts
19
Keys to Efficient Design
Rain Bird Maxi Paw 08 nozzle .45 in/hr at 45psi Matched Precipitation Rate
20
Keys to Efficient Design
21
Keys to Efficient Design
Matched Precipitation Rate Rotor Nozzles
22
Keys to Efficient Design
23
Keys to Efficient Design
Rain Bird Maxi Paw 08 nozzle .45 in/hr at 45psi Rain Bird Mini Paw 07 nozzle .38 in/hr at 45psi Rain Bird 10H nozzle 1.52 in/hr at 30psi Toro 8H nozzle 1.80 in/hr at 30psi Toro 15H nozzle 1.77 in/hr at 30psi Toro 12H nozzle 1.72 in/hr Hunter PGP 06 nozzle .36 in/hr at 40psi Hunter 10A nozzle 1.88 in/hr at 40psi Hunter 17A nozzle 1.47 in/hr at 40psi
24
Keys to Efficient Design
Distribution Uniformity (DU) The DU is a measurement of uniformity, expressed as a percentage, comparing the driest 25% of the area to the average distribution in the area (DU low quarter). A perfectly uniform application would be represented by a DU of 100%. A less uniform application is represented by a lower percentage.
25
Keys to Efficient Design
26
Keys to Efficient Design
27
Keys to Efficient Design
PRS ensures optimal performance at 30 PSI Eliminates misting & fogging Reduces costly accidents and property damage Restricts water loss by 70% with damaged nozzle
28
Keys to Efficient Design
Rain Bird 5000 Series Rotor with PRS: In-stem pressure regulation reduces inlet pressure to 45 psi Eliminates head-to-head pressure variation Eliminates misting Improves distribution uniformity
29
Keys to Efficient Design
Hunter PRB Rotors (PGP & I20 models available)
30
Keys to Efficient Design
Pressure-compensating emitters
31
Most irrigation manufacturers now sell “Smart Controllers”
Keys to Efficient Design Most irrigation manufacturers now sell “Smart Controllers” 1. Most manufacturers now offer one or more types of “smart” controller.
32
Spare Keys 1. Sprinklers have to have enough
water and pressure to work 2. Don’t mix and match different kinds of sprinklers on a zone 3. Smart Controller on idiot sprinkler system equals idiot sprinkler system Don’t exceed a velocity of 5’ per second in lateral piping Use head-to-head spacing
33
Spare Keys 6. Use goof plugs 7. Use water tight wire connectors
8. Don’t run ½” poly more than 300’ 9. Don’t run spaghetti more than 5-10’ 10. Use pressure compensating emitters Also not head-to-head spacing! 11. Use MPR nozzles 12. Use high efficiency nozzle
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.