1. Introduction to Mathcad

2. DISCLAIMER & USAGE
The content of this presentation is for informational purposes only and is intended for students attending Louisiana Tech University only.
The authors of this information do not make any claims as to the validity or accuracy of the information or methods presented.
Any procedures demonstrated here are potentially dangerous and could result in damage and injury.
Louisiana Tech University, its officers, employees, agents and volunteers, are not liable or responsible for any injuries, illness, damage or losses which may result from your using the materials or ideas, or from your performing the experiments or procedures depicted in this presentation.
The Living with the Lab logos should remain attached to each slide, and the work should be attributed to Louisiana Tech University.
If you do not agree, then please do not view this content.
boosting application-focused learning through student ownership of learning platforms

3. Mathcad is like a digital engineering notebook.
Calculations are a critical part of engineering, and documenting these calculations is important.
Mathcad is like a digital engineering notebook.
Uses and benefits of Mathcad include:
Live mathematical notations
Units intelligence
Powerful calculation capabilities
Calculation presentation through graphs, plots, text, and images
Source:

4. Mathcad Interface Ribbon user interface with tabs:
Math, Input/Output, Functions, Matrices/Tables, Plots, Math Formatting, Text Formatting, Calculation, Document, & Resources
Cursor identifying where you are on the worksheet
Worksheet used to write all calculations and other documentation.
Think of this as “smart” paper

5. Typing Calculations Versus Text
Math Mode:
Do you notice any subtle differences in the Math Mode versus the Text Mode?
Text Mode:
Both Math and Text Modes can be useful depending on what you are trying to accomplish.
Text Mode allows you to input text in the worksheet, like comments or other forms of documentation that you do not need the worksheet to calculate.
Math Mode allows you to input data (number and units) that may be used in your calculations.
By default the worksheet is written in math mode.
You need to tell the worksheet to shift to text mode.
Under the Math tab, click Text Block (large block allotted for text) or Text Box (smaller box allotted for text).

6. Predefined Variables & Units
Mathcad has predefined variables for commonly used values.
Notice how the predefined variable turns green when you type.
After you press = the predefined value appears.
You should AVOID redefining the predefined variables by using them for different variables (e.g., setting g=10lbf, because g is already defined as gravity = 9.81 m/s2).
Mathcad has predefined units and can move seamlessly between metric and US Customary units.
Notice how the units turn blue when you type them or when they appear after the = sign.
If using US Customary units, after you press = Mathcad will automatically convert to metric units.
You should AVOID redefining the predefined units by using them for different variables (e.g., setting m=10lbf, because m is defined as meters)

7. Using Mathcad Use the example problem to build a Mathcad Worksheet
Example Problem: For the forces and angles depicted below, what is the magnitude of the resultant force (provide answer in lbf), and what is the angle that the resultant force makes with the x-axis (provide answer in degrees)?
𝐹 1 = 𝑙𝑏𝑓
𝐹 2 =850 𝑁
𝜃 1 =0.489 𝑟𝑎𝑑
𝜃 2 =18°
First, set up your sheet like you would with any engineering problem – Use Engineering Format
Insert text boxes to format the heading, label the problem, type the given information.
Format the text in the Text Formatting tab.

8. Using Mathcad Use the example problem to build a Mathcad Worksheet
Example Problem: For the forces and angles depicted below, what is the magnitude of the resultant force (provide answer in lbf), and what is the angle that the resultant force makes with the x-axis (provide answer in degrees)?
𝐹 1 = 𝑙𝑏𝑓
What do you notice about these given values?
𝐹 2 =850 𝑁
𝜃 1 =0.489 𝑟𝑎𝑑
Do you need to convert the units before entering them into Mathcad?
𝜃 2 =18°
No! Mathcad can seamlessly translate between the different unit systems. You can type the values as given in the problem.
Once the initial format is set for the worksheet, you need to insert the given variables.
Why are the equal signs preceded by “:”?
When you are assigning a value to a variable, Mathcad needs to know this is your intent.
The “=“ on your keyboard is used by Mathcad to calculate values.
Assigning values uses a special equal sign “:=“ that you get by pressing <shift> ;
To insert θ (or other Greek letters), click symbols section in the Math Tab.
To place a subscript press <ctrl> -

9. You will likely need to do some preliminary calculations before getting to your solution.
Notice how text is used like comments to help understand what is being calculated.
Using Mathcad
Break F1 and F2 into their x and y components.
:= is used to define the values being calculated
= is used to calculate the answer
Even though the answer is asked to be in lbf, intermediate calculations can be left in N.
Notice, we do not type the units for F1 or θ1 since the units are already stored within the variable.
Rule of Thumb: Type a unit whenever you type a number, not when you type a variable!
Be aware of the direction of your forces.
Since F2y is in the negative direction, you need to put a – sign here.
Mathcad is smart, but not that smart!

10. Using Mathcad Notice R is defined using := then calculated with =
To get the square root symbol you press \
To get exponents press ^
Initially the calculation will be given in Newtons
Within the calculation box, erase the N and type lbf (must be lbf to calculate force)
Notice θ is defined using := then calculated with =
To get the division symbol you press /
Initially the calculation will be in rad
Within the calculation box, a unit box will appear, type deg

11. Formatting and Other Tips
Use the Math Formatting tab to:
Highlight math text
Change the color of math text
Change font type and size
Edit the appearance of a number
Result Format – General, Decimal, Scientific Notation
Display Precision – Change number of decimal places
Resources Tab
Help feature – large library of information, includes sample text that you can copy and paste into your worksheet help you get started on a calculation.
Tutorials – sample exercises to help familiarize yourself with Mathcad.
Keyboard shortcuts – list of keyboard shortcuts that will make using Mathcad much easier.