1. Additional Upstream Coil Shielding
SHMS
Bender Magnet
Additional Upstream Coil Shielding
11/22/2018

2. Target Chamber Spray Angles
SHMS
Bender Magnet
Target Chamber Spray Angles
11/22/2018

3. Spray Angle Through Chamber Window
Target Center
24.5 Inches
(62.2 cm)
Beam
4.33 Inches
(11 cm)
15 Inches
(38.1 cm)
Tungsten
39°
.8 Inches
(2 cm)
1916 lb
Spray Angle Through Chamber Window
11/22/2018

4. Beam Spray Angle From Target Target 8.66 Inches (22 cm) Shield Block
Illustrating SHMS at Angle of 40°
11/22/2018

5. Shielding Aperture Info
SHMS
Bender Magnet
Shielding Aperture Info
11/22/2018

6. Bender Magnet Window Frame Assembly 5 5/8 x 5 5/8
Window opening on
Bender Magnet Window Frame Assembly
5 5/8 x 5 5/8
11/22/2018

7. Window opening on Bender Magnet Window Frame Assembly
5 5/8
5 5/8 6
4.75
Window opening on Bender Magnet Window Frame Assembly
5 5/8 x 5 5/8
11/22/2018

8. 11/22/2018

9. SHMS
Bender Magnet
Shielding Block
and
Support Assembly
11/22/2018

10. Bender Shielding Support
Bender Lead Shielding
Assembly
Shield Support
Cradle Assy
(Aluminum)
Shield Stabilizing Gusset
Assembly
(Aluminum)
Locator Pin Assy
HSR 85A Guide
(Existing)
Adjustable
Position Stop
Slide Assy
Travel Stop
(Aluminum)
Shield Slide Support Weldment
(Steel)
Vertical Adjusters
Support Base Plate
Assembly
Adjustment Pushers
(6 Places)
Bender Shielding Support
11/22/2018

11. Beam Bender Magnet Shielding Assembly 25.5 Inches 15.75 Inches
Target Center
25.5 Inches
(64.8 cm)
15.75 Inches
(40 cm)
Beam
25.3 Inches
(64.3 cm)
Lead
1800 lb
Bender Magnet Shielding Assembly
with GEM Slide Assembly Installed
11/22/2018

12. Bender Magnet Shielding
15.75 Inches (40 cm)
Lead Shielding 1800 lbs
Tungsten
Wedge Insert
.70 Inches
(1.8 cm)
.20 Inches
(.5 cm)
Bender Magnet Shielding
Illustrating clearances between Lead Shielding and existing hardware
11/22/2018

13. Beam Bender Magnet Shielding 15.75 Inches (40 cm) Lead Shield
HMS Snout shown HMS at minimum achievable angle while SHMS is at min angle of 5.5°
Beam
Notch cut in Lead Shielding
To clear HMS Snout Flange
Bender Magnet Shielding
Illustrating HMS Snout proximity with SHMS at Min Angle of 5.5°
11/22/2018

14. Shielding Block Assembly
SHMS
Bender Magnet
Shielding Block Assembly
11/22/2018

15. Main Shield Block Installation
1270 lbs
Main Shield Block Installation
11/22/2018

16. Additional Shield Block Installation
Shielding Bar
130 lbs
Main
Shield Block
Additional Shield Block Installation
11/22/2018

17. Shield Bar
Fastener
Upstream
Downstream
Plates
Mounting
Brackets
Step 1
Step 2
Step 3
Install Main Lead Shield Block in Support Cradle and secure to Upstream and Downstream Plates
Install Lower Shielding Bar and secure to Support Cradle at attachment brackets
Stack Shielding Bars. Forth Bar (unsupported) shall be fastened to Main Lead Shield Block
11/22/2018

18. Tie Plate
Tungsten Wedge Insert
Mounting Bracket
Step 3
Step 4
3) Install remaining Shield Bar, and secure to Main Shield Block with Tie Plate
4) Install Tungsten Wedge Insert and secure with Mounting Bracket
11/22/2018

19. Shielding Installation
SHMS
Bender Magnet
Shielding Installation
11/22/2018

20. Modify Mounting Bracket (shorten)
15.75 Inches
(40 cm)
.70 Inches
(1.8 cm)
Option #1
Modify Mounting Bracket (shorten)
Option #2
Fabricate new shorter Mounting Bracket
11/22/2018

21. 11/22/2018

22. Shielding Traverse Distance
SHMS
Bender Magnet
Shielding Traverse Distance
11/22/2018

23. Linear Slide Traverse Distance
24.0
Linear Slide Traverse Distance
11/22/2018

24. Linear Slide Traverse Distance
24.0
Linear Slide Traverse Distance
11/22/2018

25. Shielding traversed to allow for Bender Sieve Service
11/22/2018

26. Shielding traversed to allow for Bender Sieve Service
11/22/2018