1. SCHEMATIC MANOEUVRE ILLUSTRATIONS
Flying and Judging F3A
SCHEMATIC MANOEUVRE ILLUSTRATIONS
SCHEDULE F-09 1

2. ( not judged, not scored )
Take-off sequence
( not judged, not scored )
wind
Turnaround manoeuvre of the competitors choice
520m
150m
180° turn
300m
1200
security line 4

3. F-09.01: Loop with full rolls integrated in each 180 degree half
First roll and second roll must be in opposite directions
Loop must be round.
Rolls must be integrated on circular flight path 5

4. F-09. 02: Stall turn, full snap roll up, 2/4-point roll down,
F-09.02: Stall turn, full snap roll up, 2/4-point roll down, inverted exit
Snap roll on middle of the line.
If snap roll = barrel roll or aileron roll: Severe downgrade > 5 pts.

5. F-09. 02: Stall turn, full snap roll up, 2/4-point roll down,
F-09.02: Stall turn, full snap roll up, 2/4-point roll down, inverted exit
Two wing spans or more = zero
Pivot on CG
2/4 roll on middle of the line.
2/4 roll
All radii are equal.

6. F-09. 03: 4/8 point rolls in opposite direction, inverted entry
F-09.03: 4/8 point rolls in opposite direction, inverted entry and exit
Roll rates must be same on all points.
Duration of points must be same.
4/8-pt roll
4/8-pt roll

7. F-09. 04: Push-pull-pull humpty pump, 2/4-point roll up,
F-09.04: Push-pull-pull humpty pump, 2/4-point roll up, /2 roll down, inverted entry
2/4-pt roll
2/4-pt. roll on middle of the line.

8. F-09. 04: Push-pull-pull humpty pump, 2/4-point roll up,
F-09.04: Push-pull-pull humpty pump, 2/4-point roll up, /2 roll down, inverted entry
1/2 roll
1/2 roll on middle of the line.
All radii are equal.

9. F-09.05: 1 1/2 snap roll from knife edge, inverted exit
Knife-edge portions of equal duration and length
The direction of the rolls is L-R-R or R-L-L
1/4roll
1 1/4 snap roll
1/4 roll

10. F-09.06: Half square loop, two half rolls in upline, inverted entry
All radii are equal.
Rolls on middle of the line.

11. F-09. 07: Outside loop, integrated 4-point roll over bottom
F-09.07: Outside loop, integrated 4-point roll over bottom degree half
Loop must be round.
Integration occurs over bottom 180° half.
Four-point roll must be integrated on circular flight path.
Roll rates must be same.
Duration of points must be equal.

12. F-09. 08: Reverse top hat; 3/4 rolls down and up,
F-09.08: Reverse top hat; 3/4 rolls down and up, horizontal cross box inverted, inverted exit
3/4 roll
3/4 roll
Rolls in middle of the lines.
Horizontal cross box must be inverted.
Al radii are equal.

13. F-09.9: Two turn inverted spin, inverted entry and exit
Snap entry, zero points
Forced entry, downgrade.

14. F-09. 10: Shark fin, two 1/2 rolls opposite, with 2/4-point
F-09.10: Shark fin, two 1/2 rolls opposite, with 2/4-point roll in downline, inverted entry and exit
1/2 roll
2/4 roll
1/2 roll
45°
All radii are equal.

15. F-09. 11: Triangle loop, two point roll and full roll,
F-09.11: Triangle loop, two point roll and full roll, inverted entry and exit
90°
Full roll
2/2-pt roll
Rolls in middle of the lines.

16. F-09. 11: Triangle loop, two point roll and full roll,
F-09.11: Triangle loop, two point roll and full roll, inverted entry and exit
90°
Full roll
2/2-pt roll
Al radii are equal.

17. F-09.12: Stall turn3/4-point roll up, 3/4 roll down, inverted entry
Pivot on CG
Two wing spans or more = zero
All radii are equal.
3/4 roll
3/4-pt roll

18. F-09.13: Knife-edge loop Entry and exit at same height.
The loop must be round.

19. F-09.14: Half loop, two oppsite full rolls integrated, exit inverted
Half loops must be round.
Full roll integrated
Roll reversal is immediate.
Full roll integrated

20. F-09. 15: Horizontal hourglass, knife-edge and full roll
F-09.15: Horizontal hourglass, knife-edge and full roll in uplines, inverted entry and exit
Al radii are equal.
1/4 roll
Knife-edge on middle of the 45° upline.
Full roll
Full roll on middle of the 45° upline.
1/4 roll
45°

21. F-09. 16: Reverse pull-push-pull humpty bump, 2/4-point roll
F-09.16: Reverse pull-push-pull humpty bump, 2/4-point roll down, full roll up, inverted entry and exit
2/4-pt roll
Full roll
Rolls on middle of the line.

22. F-09. 16: Reverse pull-push-pull humpty bump, 2/4-point roll
F-09.16: Reverse pull-push-pull humpty bump, 2/4-point roll down, full roll up, inverted entry and exit
All radii are equal..

23. F-09. 17: Two opposite snap rolls on 45 degrees
F-09.17: Two opposite snap rolls on 45 degrees down, inverted entry, 1/2 roll on exit
If snap roll = barrel roll or aileron roll: Severe downgrade > 5 pts.
Snap rolls on middle of the line.
45°
All radii are equal.
1/2 roll

24. Landing (not judged, not scored)
Upright flight
1800 TURN
1800
Kurve
1800
TURN
150m
300m
1200
Peter Uhlig, im Januar 2005

25. Thank you! Forget WHO is flying! Forget WHAT is flying!
LOOK ONLY AT LINES DESCRIBED IN THE SKY!
Thank you!
Peter Uhlig, August 2007