1. Laser 3000™ Operating Instructions
(To be read in conjunction with the User Manual)
© Laserex Technologies Pty Ltd 2013

2. Battery Installation Ensure batteries are installed as shown below
2 Batteries –ve up
2 batteries +ve up
Failure to install the batteries correctly can result in damage to the unit.
Storage Information: If the Laser 3000™ is not going to be used for sometime, it is highly recommended that the batteries be removed from the unit. This will significantly increase the lifetime of the battery.

3. Switching the unit on Press the Green on button On / Off Up Enter Down
Start / Stop
Restart

4. Switching the unit on The following appears on the screen
Press UP to increase the digit, DOWN to decrease. Press ENTER to go to the next screen.
Hold ENTER for a few seconds to go back to the previous digit

5. Switching the unit on
The PIN is factory set to 9999 by Laserex. The first 9 will appear on the screen. Press ENTER until the second asterisk becomes a 9, then press ENTER again until 9999 appear on the screen. After the 4th asterisk becomes a 9 the word OK will appear in yellow alongside ENTER on the screen.
Press ENTER and ‘correct’ appears on the screen in green. If you make a mistake when entering a number, press ENTER for a few seconds and the digit returns back to an asterisk. Then input the correct digit. The next screen is:

6. Switching the unit on

7. If using the Laser 3000™ indoors
Ensure RF safety interlock is attached to the door of the room
Wear laser safety eyewear provided with unit
Attach with double sided tape on door and door frame of room. Ensure arrows are pointing to each other
Laser Safety Eyewear must be worn as the Laser 3000™ is a Class 3B laser

8. Attaching the RF interlock
Place double sided tape on the back of the RF interlock
Attach to door frame and door of room
Make sure arrows are facing each other
Arrow
Arrow

9. Switching the unit on for indoor use
To manually input a dosage:
At the Data Source screen press DOWN so that Manual Input is highlighted in blue. The following screen appears:
Dosage Selection: Dose will be highlighted in blue. Press ENTER and the number of Joules are highlighted in orange. Press UP to increase the dosage or DOWN to decrease. When the correct dosage is entered, press ENTER.
Frequency Selection: Frequency (Freq) will be highlighted in blue and Continuous Wave (CW) will appear highlighted in orange. If you wish to use the Laser 3000 in CW press ENTER to move to the Interlock setting.
To change the frequency from CW to one of 7 programmed Nogier frequencies, press UP (with CW highlighted in blue) once to 73Hz, twice to 146Hz and so on. With the selected frequency highlighted in orange, press ENTER to the Interlock setting.

10. Indoor use of the Laser 3000™
RF Interlock: After pressing ENTER, Interlock will be highlighted in blue. If the interlock is disabled, the letters DIS will appear on the screen in orange. Press ENTER and the following screen appears

11. Indoor use of the Laser 3000™
Press UP until INT 1 is highlighted, then press ENTER and EN (enabled) appears. Repeat the above until INT 2 is also enabled. If you are only using one RF Interlock, make sure that at least one of the Interlocks is enabled. If only one Interlock is enabled, say INT 1, press DOWN. INT 2 will appear as DIS.
OK will then appear, highlighted in blue. Press ENTER. NEXT will appear highlighted in blue. Press ENTER. Laser Standby! will appear in green.
Press ENTER and an image of laser safety eyewear appears along with the words ‘Safety glasses must be worn’ appearing in red.

12. Operating the Laser 3000™ The next screen states
START will appear in red
Press the Start button
Laser On! Appears in red and an audible beep will be heard

13. To repeat the same dosage
After the treatment, Laser Standby! will appear in green on the screen
NEXT will be highlighted in blue
Press ENTER, an image of laser safety glasses appears.
Press the START button.
START will be highlighted in red
The same dosage will be delivered

14. To use a different dosage
After completing a treatment, Laser Standby! will appear in green on the screen. NEXT will be highlighted in blue
Press Down so that PREV is highlighted in blue
Press Enter
With Manual Input highlighted in blue, press Enter
DOSE will be highlighted in blue.
Press Enter and vary the dosage, Frequency etc
With the correct setting selected & interlock enabled, OK will be highlighted, Press Enter. Next will be highlighted in blue. Laser Standby! appears in green. Press Enter and Laser Safety Eyewear appears on the screen. Laser Ready! appears and START is highlighted in red. Press the red Start button.

15. Storing a dosage After manually inputting a dosage, frequency etc
At the following screen:
With NEXT highlighted, press DOWN and SAVE appears highlighted in blue
Press Enter and Save Memory appears in orange.
M will appear at the bottom of the screen with a number highlighted in blue. Press Enter. OK will be highlighted in blue. Press Enter and the dosage will be stored.
The next time you wish to use the same dosage, at the data source screen select Load Memory

16. If using the Laser 3000™ outdoors
Ensure laser safety eyewear provided with the unit is worn
If others are present, laser safety eyewear should also be worn
Whether indoors or outdoors, NEVER point the Laser 3000™ in the direction of someone’s eyes
Laser Safety Eyewear must be worn as the Laser 3000™ is a Class 3B laser

17. Switching the unit on for outdoor use
Enter the dosage, frequency etc as previously explained.
There is no need to have the interlock attached.
The same procedure applies to repeat a same dosage or deliver a different dosage

18. Attaching the Laser 3000™ head
To begin, ensure that the notch on the head is located at the 10 o’clock position
Turn the head clockwise so that it clicks into place at the 12 o’clock position
12 o’clock
10 o’clock

19. Correct Head Position
Notch at 12 o’clock position

20. Changing the head continued
It is important for the head to be in this position in order for the Laser 3000™ to operate. Otherwise, damage can be done to the internal circuitry

21. Re-charging the Laser 3000™
Place the 4 re-chargeable batteries in the re-charger
Plug re-charger into mains power
A Red light will appear when switched on.
light

22. Using the IR Card
To test if the Laser 3000™ is working, place the head of the unit face down onto the IR card provided
Switch the Laser 3000™ on
The orange square will illuminate indicating the laser is operational

23. Laser 3000™ contact details
If you have any questions, please contact Laserex Technologies Pty Ltd
Web:
Tel:
Twitter: Equinelaser3000
© Laserex Technologies Pty Ltd 2013