1. Electrical Engineering Lab I
EECE 1101
Electrical Engineering Lab I

2. Taaruf Nor Farahidah Za’bah Room number : E2-2-13.12
Phone number :
address :
The lab technician is
Br. Saiful Redzuan
The lab demonstrator is
Br. Akhter
Course website:
Taaruf

4. Weeks Topics Task/Reading 1 Introduction to Lab 22
Experiment #1: Ohm’s Law & Series and parallel circuits
Experiment #1 3 4
Experiment #2: Kirchoff’s voltage and current laws
Experiment #2 5
Experiment #3: Thevenin’s and Norton’s theorem and Maximum power transfer theorem
Experiment #3 6
Experiment #4: Superposition Theorem
Experiment #4 7
Experiment #5: Transient Response of an RC Circuit
Experiment #5 8
Introduction to Simulation Software PSPICE 9
Experiment #9: Inverting and Non-Inverting Op-Amp
Experiment #9 10
Experiment #6: Diode Characteristic and Application
Experiment #6 11
Experiment #7: BJT Characteristic and Biasing Circuits
Experiment #7 12
Experiment #8: MOSFET - Common Source Amplifier
Experiment #8 13
Preparation Week 14
Final Test

5. Assessment
Quiz
20 %
Lab Report
40 %
Final Test

6. Safety
Please wear covered shoes – NO SLIPPER. Otherwise, you will be asked to leave the lab.
Please wear the green Kulliyyah jacket
Power must be switched off whenever an experiment or project is being assembled, disassembled, or modified.

7. Tidiness
When the experiment has been satisfactory completed and the results approved by the instructor, the students may disconnect the circuit and return the components and instruments to the locker tidily.
Chairs are to be slid in properly.
DO NOT WRITE anything on the table

8. Preparation
Read the entire experiment and research any required theory beforehand. Many times an experiment takes longer that one class period simply because a student is not well prepared.
The experiment is performed in pairs (max=3 students per group) but the final exam is performed individually
One group = one lab report

9. Lab Reports Reports have to be handwritten for submission.
Writing should appear on one side of each sheet only.
The students’ name & matric number, section number, lab session and the lecturer’s
Please indicate the author of each section in your report.
The cover page of the lab report can be downloaded from the website.

10. Report Format and Evaluation
No.
Evaluation Items
Experiment 1-5
Experiment 6-9
Marks 20% 1
Objectives 2
Experiment Set-up 4 3
Results/Observations 5
Discussion and Conclusion 9 6
PSPICE
TOTAL 20

11. Preparation for PSPICE Tutorial
Download 16.6_OrCAD_Lite_Capture&PSpice_Products.zip from the any computer in the lab
It is a zipped file, you have to extract the files into a designated folder
Once you have extracted, go to Disk 1 and look for SETUP (it is an application file) to install the software.
One group will require ONE laptop for the tutorial sessions

12. Introduction to Lab Equipment
Bread board and its connections

14. Function Generator
To create AC signals such as Sine-Wave, Triangular Waves and Square Wave
The user can alter its frequency and amplitude
Example of a function generator

15. Oscilloscope An equipment to show the obtained result. Has 2 channels
One for input signal
One for output signal

16. DC power supply
To provide DC supply to your circuit which you can measure using digital multi-meter

17. SEPTEMBER OCTOBER M T W F S 5 6 7 8 9 10 11 Intro 12 13 14 15 16 17 18
Intro  12 13 14 15 16 17 18
HOLIDAY 19 20 21 22 23 24 25
 LAB 1 26 27 28 29 30 1 2
 LAB 2
AWAL MUHARRAM
OCTOBER 3 4
LAB 3 
 LAB 4
 LAB 5
MID SEMESTER BREAK 31

18. NOVEMBER M T W F S DECEMBER 1 2 3 4 5 6 WORKSHOP ON PSICE 7 8 9 10 111 2 3 4 5 6
WORKSHOP ON PSICE 7 8 9 10 11 12 13
LAB 9 14 15 16 17 18 19 20
LAB 6 21 22 23 24 25 26 27
LAB 7 28 29 30
 LAB 8
DECEMBER
BREAK
HOLIDAY
 FINAL TEST