1. SHEET 1 - .025 F20-06 t-deck T11-01 vert-tail W22-01L wingtip F20-03R
F20-03L
F20-04L
F20-04R
F20-02R
F20-02L
F22-03
F20-05
SHEET
F22-01 aft fuse bottom
F08-03 (ctr stick)
C05-04 (2 stick)
C05-09 (2st lower)
Seat
W22-01R wingtip
L06-13
D02-05
P15-10
W04-10

2. Unallocated sheet – errors/corrections / extra ribs, etc.
W19-02 lower aft wing skin
T05-01L h-tail skin
Unallocated sheet – errors/corrections / extra ribs, etc.
*Lay out tail skin on paper first, then position on sheet. Will fit with ~3/8” to wing skin rectangle. More clearance (~2”) can be obtained by laying out wing skin edge curves “inside out” from plans view.
Actual skin profile if laid out “inside out” relative to plans.
Bend line
VERY TIGHT
Want this to be aft edge of Wing
SHEET
W19-02 lower aft wing skin
T05-01L h-tail skin
Unallocated sheet – errors/corrections / extra ribs, etc.
*Lay out tail skin on paper first, then position on sheet. Will fit with ~3/8” to wing skin rectangle. More clearance (~2”) can be obtained by laying out wing skin edge curves “inside out” from plans view.
Actual skin profile if laid out “inside out” relative to plans.
Bend line
VERY TIGHT
Want this to be aft edge of Wing

3. SHEET 5 - .025 W15-05 fwd wing ribs (1) (2) (3) (4) (5) (6) (7) (8)
(9)
(10)
(11)
(12)
(13)
(14)
W18-01L fwd wing skin
W16-06 (5)
W16-06 (4)
W16-06 (3)
W16-06 (2)
W16-06 (1)
W16-06 (6)
W18-01R fwd wing skin
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
W15-05 fwd wing ribs
W16-06 (11)
W16-06 (10)
W16-06 (9)
W16-06 (8)
W16-06 (7)
(suggestion – cut extra wide by amount needed to allow symmetrical bending if using vacuum form method)
Upper Side of Wing
SHEET
W16-06 (14)
W16-06 (12)
W16-06 (13)
(suggestion – cut extra wide by amount needed to allow symmetrical bending if using vacuum form method)
Upper Side of Wing

4. SHEET 7 - .025 W16-06 (20) F26-01R tail cone side W16-06 (19)
W19-01 upper aft wing skin
W16-06 (20)
W16-06 (19)
W16-06 (16)
W16-06 (15)
W16-06 (18)
W16-06 (17)
(tight fit)
Aft Edge of Wing
SHEET
F26-01L tail cone side
W19-01 upper aft wing skin
W16-06 (26)
W16-06 (25)
W16-06 (22)
W16-06 (21)
W16-06 (23)
W16-06 (24)
(tight fit)
Aft Edge of Wing

5. SHEET
F20-01L
F20-01R
W10-02
W10-01
F13-01
F07-03
SHEET
F24-13
F24-12
W20-01L
W20-01R
F17-04
F16-01
Battery box, spar tip webs, flap / aileron / elevator ribs
This series of cut sheets is for:
-Plans building (no kit)
-Buying pre-bent metal kit from Sonex, so no material is included for flap skins, etc.