1. Formalin Training Anatomy and Physiology Laboratory
Department of Animal and Food Sciences
Brigham Young University Idaho

2. What is formalin?
Formalin is formaldehyde that has been mixed with water.
Formaldehyde is an OSHA regulated chemical that is colorless, flammable, and has it’s own distinct odor. OSHA sets exposure levels to formaldehyde containing solutions due to the health effects and risks that are associated with length and concentration of exposure.

3. How is formalin used?
Formalin is used to embalm or preserve tissue or necropsy samples.

4. How can I control my exposure?
OSHA requires that individuals are limited to specific amounts of exposure to formalin. A significant way to limit exposure is through ventilation. Our anatomy and physiology lab was designed with engineering controls and ventilation to ensure that we do not exceed these amounts. The laboratory is designed with a ventilation system to remove formalin at the necropsy table.

5. In order to ensure that the ventilation system at the necropsy table is working correctly a sensor has been placed on the wall by each table as shown below. The green light must be ON. If no light or a red light is on- wait for your instructors directions on how to proceed with the lab.
The laboratory space is also designed to constantly bring in fresh air and remove current air. These engineering controls help to minimize exposure to any airborne formalin. These engineering controls are monitored by the University Safety Office.

6. Personal protective equipment protects us from the other forms of exposure such as skin contact and splashes. You will need to wear:
A lab coat
Safety Glasses or Goggles
Gloves
Long pants
Enclosed shoes

7. There should be no eating, drinking, or applying cosmetics in the laboratory to prevent unintentional ingestion.

8. What are the health risks of formalin?
The health risks associated with formalin can be located on both the bottle label as well as the SDS (Safety Data Sheet).

9. Most exposures to formalin are respiratory
Most exposures to formalin are respiratory. If you are bothered get some fresh air.

10. If you splash formalin in your eye – go to the eyewash station and wash your eye for 15 minutes. Report this to your instructor or TA.

11. If you splash formalin on your skin- wash it off with soap and water
If you splash formalin on your skin- wash it off with soap and water. If you get a large amount on your lab coat- you should wash your lab coat. If your clothing smells like formalin- it is dirty and needs to be washed!

12. How do I properly dispose of formalin?
Formalin is considered hazardous waste. In our laboratory we have a barrel for all excess liquid formalin. Since there is not a snorkel above the barrel- please open the outside door beside the barrel to increase ventilation.
To add formalin to the barrel:
Look to see how full the barrel is- enough room go to step 2. (not enough room see next slide)
Open outside door
Unscrew the white cap
Place the funnel in the hole
Pour the formalin from your container into the barrel.
Remove the funnel
Screw the white cap back on the barrel.
Close outside door tight

13. If the barrel is close to the fill line (marked by tape or black marker)- do not add any more to the barrel. Add your formalin to the overflow bottle under the sink and notify your TA, Instructor, or the Lab Manager that the barrel is full and needs to be replaced. The same steps apply to using the the overflow bottle as with the barrel.

14. What if I spill?
The formalin barrel is sitting on absorbent pads and has an absorbent ring on the top of the barrel. If your spill is more than these pads can handle you can get additional pads from the shelf to absorb the spill. Contact the lab manager to take care of the contaminated absorbent pads.

15. If you have a large liquid spill on the concrete floor, pour some formaldehyde solidifier (see picture) on the liquid to inhibit it’s volatility, cover with an absorbent pad and notify your instructor or lab manager. The lab manger or safety office will take care of the spill from there.

16. Who can I contact for help?
If something happens and you aren’t sure what to do please contact one of the following:
Your laboratory TA
Your Instructor
The Lab Manager : text, call, or
The Safety Office :