1. Lesmahagow High School
Graphic Communication
Department of
Technological
Education

2. Interpenetration of 2 Cylinders
Department of Technological Education
Interpenetration of 2 Cylinders
The drawing shows the part Plan and part Front Elevation of an interpenetration between two cylinders.
Draw :-
The completed Elevation
The completed Plan
The End Elevation

3. Drawing Generators on Plan and Elevation
Department of Technological Education
Drawing Generators on Plan and Elevation
Divide the Elevation and Plan into 30o/60o parts and number each of the points. 9
10/ 8
11/ 7
12/ 6 1 /5 2 /4 3
Draw generators from these points on the Plan until they cut the main cylinder.
11/ 1
10/ 2 12 9/ 3
Project the generators on the Elevation parallel to the angle of the sides of the small cylinder. 8/ 4 7/ 5 6

4. Finding Points of Interpenetration
Department of Technological Education
Finding Points of Interpenetration
Project points from Plan where generators cut the main cylinder.
12/
11/
10/ 1 2 9 8 7 6 3 /4 /5
Mark where each of the projected lines cross the appropriate generators on the Elevation with a small dot. 12
11/
10/ 9/ 8/ 7/ 6 1 2 3 4 5
Draw a smooth curve through each of the points.
This line of interpenetration can now be darkened.

5. Drawing Generators for End Elevation
Department of Technological Education
Drawing Generators for End Elevation
Find the position of the End Elevation.
12/
11/
10/ 1 2 9 8 7 6 3 /4 /5
Project the 12 points from the Plan onto the End Elevation.
Number the points found on the End Elevation. 10 11 12 1 2 9 3 8 7 6 5 4 12
11/
10/ 9/ 8/ 7/ 6 1 2 3 4 5

6. Finding Points of Interpenetration on End Elevation
Department of Technological Education
Finding Points of Interpenetration on End Elevation
Project the points from the curve of interpenetration on the Elevation across to the End Elevation.
12/
11/
10/ 1 2 9 8 7 6 3 /4 /5
Mark where these lines cross the appropriate generator on the End Elevation with a small dot. 9 8 4 5 6 7 3 2 1 12 11 10 12
11/
10/ 9/ 8/ 7/ 6 1 2 3 4 5
Draw a smooth curve through each of the points.

7. Drawing End Ellipses of Small Cylinder
Department of Technological Education
Drawing End Ellipses of Small Cylinder
Project the points where the generators on the Elevation cross the end of the small cylinder across to the End Elevation.
12/
11/
10/ 1 2 9 8 7 6 3 /4 /5
Where they cross the corresponding generators draw a small dot, and draw a smooth line through each. 9 8 4 5 6 7 3 2 1 12 11 10 12
11/
10/ 9/ 8/ 7/ 6 1 2 3 4 5
Do the same thing to find the curve on the Plan.

8. Finishing the Drawing Department of Technological Education
To finish the drawing each of the outlines should be darkened.
Make sure that any hidden lines are identified when darkening the outlines.
12/
11/
10/ 1 2 9 8 7 6 3 /4 /5 9 8 4 5 6 7 3 2 1 12 11 10 12
11/
10/ 9/ 8/ 7/ 6 1 2 3 4 5

9. The Final Drawing Department of Technological Education
The final drawing should look like this.
The construction lines have been removed to make the drawing easier to understand.

10. PowerPoint Presentation produced by John McRae, Nairn Academy 2003