1. Guide to Networking Essentials Fifth Edition
Chapter 2
Network Design Essentials

2. Objectives Explain the basics of a network layout
Describe the standard networking topologies
Explain the variations on standard networking topologies
Describe the role of hubs and switches in a network topology
Construct a basic network layout
Guide to Networking Essentials, Fifth Edition

3. Examining the Basics of a Network Layout
To implement a network, you must first decide how to best situate the components in a topology
Topology refers to the physical layout of its computers, cables, and other resources, and also to how those components communicate with each other
The arrangement of cabling is the physical topology
The path that data travels between computers on a network is the logical topology
Topology has a significant effect on the network’s performance and growth, and equipment decisions
Guide to Networking Essentials, Fifth Edition

4. Understanding Standard Topologies
Networks are based on three physical topologies
A bus consists of a series of computers connected along a single cable segment
Computers connected via a central concentration point (hub) are arranged in a star topology
Computers connected to form a loop create a ring
Physical topologies describe cable arrangement
How the data travels along those cables might represent a different logical topology
The logical topologies that dominate LANs include bus, ring, and switching, all of which are usually implemented as a physical star
Guide to Networking Essentials, Fifth Edition

5. Physical Bus Topology Low fault tolerance
Guide to Networking Essentials, Fifth Edition

6. Signal Propagation
Computers communicate by sending information across the media as a series of signals
In a typical (copper wire) physical bus, those signals are sent as electrical pulses that travel along the length of the cable in all directions
The signals continue to travel until they weaken enough so as not to be detectable or until they encounter a device that absorbs them
This traveling across the medium is called signal propagation
At the end of a cable, the signal bounces back
Guide to Networking Essentials, Fifth Edition

7. Signal Bounce
Guide to Networking Essentials, Fifth Edition

8. Cable Termination
Guide to Networking Essentials, Fifth Edition

9. Cable Failure
Guide to Networking Essentials, Fifth Edition

10. Logical Bus Topology
Logical topologies describe the path that data travels from computer to computer
A physical bus topology is almost always implemented as a logical bus as well
Technology has moved past the physical bus, but a logical bus topology is still in use on some physical topologies, in particular a star
All computers communicate in the same way
They address data to one or more computers and then transmit that data across the cable in the form of electronic signals
Guide to Networking Essentials, Fifth Edition

11. Sending the Signal
When a computer has data to send, it addresses that data, breaks it into manageable chunks, and sends it across the network as electronic signals
All computers on a logical bus receive them
Only the destination accepts the data
All users must share the available amount of transmission time
Thus, network performance is reduced
A bus topology is a passive topology
In an active topology network, computers and other devices regenerate signals and are responsible for moving data through the network
Guide to Networking Essentials, Fifth Edition

12. Physical Ring Topology
Guide to Networking Essentials, Fifth Edition

13. Logical Ring Topology
Data in a logical ring topology travels from one device, or node, on the network to the next device until the data reaches its destination
Token passing is one method for sending data around a ring
Modern logical ring topologies use “smart hubs” that recognize a computer’s failure and remove the computer from the ring automatically
An advantage of the ring topology lies in its capability to share network resources fairly
Guide to Networking Essentials, Fifth Edition

14. Physical Star Topology
Guide to Networking Essentials, Fifth Edition

15. A Logical Bus Implemented as a Physical Star
Guide to Networking Essentials, Fifth Edition

16. A Logical Ring Implemented as a Physical Star
Guide to Networking Essentials, Fifth Edition

17. Switching Implemented as a Physical Star
Switching is neither a bus nor a ring logically, but is always implemented as a physical star
A switch takes a signal coming from a device connected and builds a circuit on the fly to forward the signal to the intended destination computer
Superior to other logical topologies because, unlike bus and ring, multiple computers can communicate simultaneously without affecting each other
Dominant method used in almost every LAN design
Guide to Networking Essentials, Fifth Edition

18. Wireless Topologies
Wireless networking has a logical and physical topology
Ad hoc topology: two computers can communicate directly with one another; sometimes called a peer-to-peer topology
Infrastructure mode: Use a central device, called an access point (AP), to control communications
Star physical topology because all the signals travel through one central device
Logical bus topology
Guide to Networking Essentials, Fifth Edition

19. Examining Variations of Physical Topologies
The major physical topologies have three typical variations or combinations
Extended star
Mesh
Combination star and bus
These combinations can be used to get the most from any network
Guide to Networking Essentials, Fifth Edition

20. Extended Star Topology
Guide to Networking Essentials, Fifth Edition

21. Mesh Topology
Guide to Networking Essentials, Fifth Edition

22. Combination Star Bus Topology
Guide to Networking Essentials, Fifth Edition

23. Hubs and Switches
Both hubs and switches can act as the center of a star topology
Basic operation was discussed briefly; this section expands on them
Guide to Networking Essentials, Fifth Edition

24. Hubs In everyday use, a hub is “the center of activity”
This definition is appropriate in network usage also
In network usage, there are a number of variations on this central theme
Active hub
Passive hub
Repeating hub (just a type of active hub)
Switching hub
Guide to Networking Essentials, Fifth Edition

25. Active Hubs Most common type of hub today
Regenerate, or repeat, the signals
Require electrical power to run
Generally, have many ports—eight or more
Also called multiport repeaters or repeating hubs
Takes a signal coming in on one port
Cleans the signal (e.g., by filtering out noise)
Strengthens the signal
Sends the regenerated signal out to all other ports
Drawback: require sharing the cable bandwidth among all connected stations
Guide to Networking Essentials, Fifth Edition

26. Passive Hubs
Guide to Networking Essentials, Fifth Edition

27. Switches Central connecting point in a star topology network
Does more than simply regenerate signals
Looks just like a hub, with several ports for connecting workstations in a star topology
Determines to which port the destination device is connected and forwards the message to that port
This capability allows a switch to handle several conversations at one time, thereby providing the full network bandwidth to each device rather than requiring bandwidth sharing
Guide to Networking Essentials, Fifth Edition

28. Constructing a Network Layout
The first step in any network design is to evaluate the underlying requirements
First determine how the network will be used, which often decides the topology you use
Decide the types of devices for interconnecting computers and sites
Finally, the type and usage level of network resources dictates how many servers you need and where to place servers
Guide to Networking Essentials, Fifth Edition

29. Selecting a Topology
Most new network designs come down to only one choice: How fast should the network be?
The physical topology will certainly be a star, and the logical topology is almost always switching
Ethernet switches are typically used on a LAN, but you might consider other logical topologies for other reasons:
Use of legacy equipment
Network size
Cost restrictions
Difficulty to run cables
Guide to Networking Essentials, Fifth Edition

30. Creating the Layout Network must be documented
Useful questions before drawing the diagram
How many client computers will be attached?
How many servers will be attached?
Will there be a connection to the Internet?
How will the building’s physical architecture influence decisions, such as whether to use a wired or wireless topology, or both?
Which topology or topologies will you use?
Network diagram must be kept up to date
Guide to Networking Essentials, Fifth Edition

31. Creating the Layout (continued)
Guide to Networking Essentials, Fifth Edition

32. Summary Basic physical topologies: bus, star, or ring
Physical bus: easy to install but outdated
The logical bus topology is still used, but is almost always implemented as a physical star
Physical ring: connects devices in such a way that the cabling starts and ends with the same computer
Rarely used (except in FDDI)
Logical ring topology typically uses token passing to send data around ring; normally implemented as a star
Physical star: centralized management and higher degree of fault tolerance
Topology of choice in today’s networks
Guide to Networking Essentials, Fifth Edition

33. Summary (continued)
For wireless networks: ad hoc or infrastructure mode
Variations on major topologies
Extended star (most widely used)
Mesh (most fault tolerant)
Combination star and bus
Hub: central point of concentration for a star network
Can be active (if it regenerates the signals) or passive
Switch: provides better performance than a hub
Device of choice in corporate star topology networks
Network layout should be consistent and maintained accurately as the network changes
Guide to Networking Essentials, Fifth Edition