1. Chapter 6 Work and Energy
Essential Questions:
What is work?
What is energy?

2. Where must we start?
For something to happen (pendulum to swing, coaster to roll, etc.), we must start with….

3. Work is…

4. Work
“When a force acts upon an object to cause a displacement of the object, it is said that work was done upon the object. There are three key ingredients to work - force, displacement, and cause. In order for a force to qualify as having done work on an object, there must be a displacement and the force must cause the displacement.” PCR

5. Work W = Force “dot” displacement W = ΙFΙ ΙDrΙ cos j OR W=(F)(Dr)cos j
Units: joule (J) one J = 1.0N x 1.0m
Work is a scalar quantity
Work is defined as:
1. The “use” of energy to accomplish something.
The process where a force acts through a displacement to transfer energy from one object (or one form) to another.

6. Lab: How do you compute Work?
The amount of work can be determined by what the worker (you in this case) gets done. You will “get done” the same thing in each trial. However, you will do it with varying forces each trial, over varying displacements. Your goal is to practice mathematically combining force and displacement to compute work. Also, understand the units for work.

7. Which is more work?

8. Inclined Plane Activity
Tilt the ramp against a support.
Measure the 2-D displacement needed (length of ramp) to raise the lab cart exactly 1.00m vertically.
Measure the force needed to drag the cart up the incline at a constant speed. Be sure to pull scale parallel to the track!
Repeat at other angles for the track, until you have done one more trial than # of students in the group.
Determine the product of the force and displacement for each of the trials. Do the first trial as a group, then each student takes responsibility for one of the remaining trials.
Report: Objective, sketch set-up, label, record measurements and results neatly in a table, show calculations

9. Example Problem:
Before beginning its initial descent, a roller coaster car is always pulled up the first hill to a high initial height. Work is done on the car (usually by a chain) to achieve this initial height. A coaster designer is considering three different incline angles at which to drag the 2000-kg car train to the top of the 60-meter high hill. In each case, the force applied to the car will be applied parallel to the hill. Her critical question is: which angle would require the most work? Analyze the data, determine the work done in each case, and answer this critical question.

10. Example Problem:
Angle Force (N) Disp. (m) Work (J) 35° 1.12x ° 1.39x ° 1.61x

11. What is needed to do work?

12. What is needed to do work?
ENERGY

13. Energy is …

14. Energy is …
The ability to do WORK

15. Mechanical Energy is either…

16. Mechanical Energy is either:
Kinetic or Potential

17. Wnet = DK
Wnet = DK (SF) (Dx) cos q= Kf – Ko If the net force is in the direction of the displacement, and the initial speed is zero… (SF) (Dx) cos 0°= Kf – 0 (m)(a) (Dx) = Kf (m) (vf2 – vo2)/2 = Kf 1/2mvf2 = Kf K = 1/2mv2

18. Kinetic Energy
K = ½ mv2

19. Gravitational Potential Energy
Ug = mgh (or mgy)
Us = ½ k(Dl)2

20. Power is…
…the rate at which…

21. Power is…
…the rate at which work is done or the rate at which energy is transferred P= W/Dt or P = DE/Dt

22. Power is…
But, Since: P=W/Dt P= (F . Dx)/Dt Then P= F . vavg