1. 4.2 Digital Transmission Pulse Modulation Pulse Code Modulation
Outlines
Pulse Modulation
Pulse Code Modulation
Delta Modulation
Line Codes
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

2. Conversions Between Signal Types
Review
Conversions Between Signal Types
Sampling
Quantizing
Encoding

3. PULSE MODULATION (PM) Sampling analog information signal
Converting samples into discrete pulses
Transport the pulses from source to destination over physical transmission medium.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

4. Cont’d... Four (4) Methods of PM 1. PAM 2. PWM 3. PPM 4. PCM
PAM–Pulse Amplitude Modulation, PWM-Pulse Width Modulation
PPM-Pulse Position Modulation, PCM-Pulse Code Modulation
Analog Pulse Modulation
Digital Pulse Modulation
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

5. Cont’d... Analog Pulse Modulation
Carrier signal is pulse waveform and the modulated signal is where one of the carrier signal’s characteristic (either amplitude, width or position) is changed according to information signal.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

6. Pulse Amplitude Modulation (PAM)
The amplitude of pulses (carrier) is varied in accordance with the information signal.
Width & position constant.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

7. Pulse Width Modulation (PWM)
Sometimes called Pulse Duration Modulation (PDM).
The width of pulses is varied in accordance to information signal.
Amplitude & position constant.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

8. Cont’d... EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

9. Pulse Position Modulation (PPM)
Modulation in which the temporal positions of the pulses are varied in accordance with some characteristic of the information signal.
Amplitude & width constant.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

10. Advantages & Drawbacks of Pulse Modulation
Requires greater BW to transmit & receive as compared to its analog counterpart.
Special encoding & decoding methods must be used to increased transmission rates & more difficult to be recovered.
Requires precise synchronization of clocks between Tx & Rx.
Noise immunity.
Relatively low cost digital circuitry.
Able to be time division multiplexed with other pulse modulated signal.
Storage of digital streams.
Error detection & correction
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

11. Sampling
A process of taking samples of information signal at a rate of Nyquist’s sampling frequency.
Nyquist’s Sampling Theorem :
The original information signal can be reconstructed at the receiver
with minimal distortion if the sampling rate in the pulse modulation
system equal to or greater than twice the maximum information
signal frequency.
fs >= 2fm (max)
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

12. Example 1
A CD audio laser disk system has a frequency bandwidth of 20Hz to 20kHz.
What is the minimum sample rate required to satisfy the Nyquist sample rate?
Ans: fs=2fm(max)=40kHz.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

13. Cont’d... Two basic techniques used to perform the sampling function:
Natural sampling
Flat-top sampling
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

14. Natural Sampling
Tops of the sample pulses retain their natural shape during the sample interval.
Frequency spectrum of the sampled output is different from an ideal sample.
Amplitude of frequency components produced from narrow, finite-width sample pulses decreases for the higher harmonics
Requiring the use of frequency equalizers
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

15. Natural Sampling EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

16. Flat-top Sampling Most commonly used in PCM systems.
Accomplish in a sample-and-hold circuit
To periodically sample the continually changing analog input voltage & convert to a series of constant-amplitude PAM voltage levels.
The input voltage is sampled with a narrow pulse and then held relatively constant until the next sample is taken.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

17. Cont’d…
Sampling process alters the frequency spectrum & introduces aperture error.
The amplitude of the sampled signal changes during the sample pulse time.
Advantages:
Introduces less aperture distortion
Can operate with a slower ADC
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

18. Flat-top Sampling EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

19. PULSE CODE MODULATION (PCM)
Basic scheme of PCM system
Quantization
Quantization Error
Companding
Block diagram & function of TDM-PCM communication system
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

20. Basic scheme of PCM system
The most common technique for using digital signals to encode analog data is PCM.
Example: To transfer analog voice signals off a local loop to digital end office within the phone system, one uses a codec.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

21. codec Coder-decoder EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

22. Cont’d...
Because voice data limited to frequencies below 4000 Hz, a codec makes 8000 samples/sec. (i.e., 125 microsecond/sample).
(Nyquist)
If a signal is sampled at regular intervals at a rate higher than twice the highest signal frequency, the samples contain all the information of the original signal.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

23. PCM Block Diagram Four step process
Most common form of analog to digital modulation (better noise and interference immunity)
Four step process
Signal is sampled using PAM (Sample)
Integer values assigned to signal (PAM)
Values converted to binary (Quantized)
Signal is digitally encoded for transmission (Encoded)
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

24. 4 Steps Process EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

25. Quantization
Quantization-the process of converting an infinite number of possibilities to a finite number of conditions.
The process of rounding off the amplitudes of flat top sample to a manageable number of levels.
The process of segmenting a sampled signal in a PCM system into different voltage levels, each level corresponding to different binary number.
The quantization levels determine the resolution of the digitizing system.
Analog signals are quantized to the closest binary value.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

26. Cont’d… Analog signal is sampled.
Converted to discrete-time continuous-amplitude signal
(Pulse Amplitude Modulation)
Pulses are quantized and assigned a digital value.
A 7-bit sample allows 128 quantizing levels.
PCM uses non-linear encoding, i.e., amplitude spacing of levels is non-linear
There is a greater number of quantizing steps for low amplitude
This reduces overall signal distortion.
This introduces quantizing error (or noise).
PCM pulses are then encoded into a digital bit stream.
8000 samples/sec x 7 bits/sample = 56 Kbps for a single voice channel.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

27. Quantized waveform Coded waveform 3 bit PCM pulse train
Sampling pulses
Quantization level (V)
Quantized waveform
Coded waveform
3 bit PCM pulse train
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

28. PCM Example EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

29. Quantization
A process of converting an infinite number of possibilities to a finite number of conditions (rounding off the amplitudes of flat-top samples to a manageable number of levels).
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

30. Cont’d… The quantization interval or quantum
= the magnitude difference between adjacent steps.
The resolution = the magnitude of a quantum
= the voltage of the minimum step size.
The quantization error (Qe) = the quantization noise (Qn)
= ½ quantum
= (orig. sample voltage – quantized level)
Folded PCM code = (sample voltage/resolution)
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

31. Cont’d... Analog input signal Qe Exactly 2V No Qe Approximately +2.6 V
Sample pulse
PAM signal
PCM code
Exactly -1V
No Qe Qe
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

32. Example 2
From the information given in the previous slide, determine the following;
(i) Resolution
(ii) Sample voltage at t3
(iii) Qe at t3
(iv) Explain the quality of the generated PCM
Ans: 1V,2.6V,0.4V,
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

33. QUANTIZATION ERROR
A difference between the exact value of the analog signal & the nearest quantization level.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

34. Types of Quantization Midtread Midrise EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

35. Example 3
Using the same information, for the PCM code for analog sample voltage of +1.07V, determine;
(i) Quantized voltage
(ii) Qe
(iii) PCM code
Ans : 1,0.07,101
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

36. Types of Quantizer
1. Uniform type : The levels of the quantized amplitude are uniformly spaced. 2. Non-uniform type : The levels are not uniform.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

37. Dynamic Range (DR)
Ratio of the largest possible magnitude/smallest possible magnitude.
Where
DR = absolute value of dynamic range
Vmax = the maximum voltage magnitude
Vmin = the quantum value (resolution)
n = number of bits in the PCM code
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

38. Example 4
Calculate the dynamic range for a linear PCM system using 16-bit quantizing.
Calculate the number of bits in PCM code if the DR = dB
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

39. Coding Efficiency = Minimum number of bits x 100
A numerical indication of how efficiently a PCM code is utilized.
The ratio of the minimum number of bits required to achieve a certain dynamic range to the actual number of PCM bits used.
Coding Efficiency = Minimum number of bits x 100
Actual number of bits
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

40. Example 5 Given A PCM system with the following parameters
Maximum analog input frequency = 4kHz.
Maximum decoded voltage at Rx = ±2.55V.
Minimum dynamic range = 46 dB
Determine :
Minimum sample rate. (ans: 8kHz)
Minimum number of bits used (ans :n=7.65≈8)
Resolution (ans : 0.01V )
Quantization error (ans: 0.01V/2=0.005V)
Coding efficiency (ans: (8.63/9)x100%=95.89%)
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

41. DIGITAL TRANSMISSION PART II

42. Signal to Quantization Noise Ratio (SQR)
The worst-case voltage SQR
SQR for a maximum input signal
The signal power-to-quantizing noise power ratio
R =resistance (ohm)
v = rms signal voltage
q = quantization interval
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

43. Example 2
Calculate the SQR (dB) if the input signal = 2 Vrms and the quantization noise magnitudes = 0.02 V.
2. Determine the voltage of the input signals if the SQR = dB and q =0.2 V.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

44. Effect of Non-Linear Coding
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

45. Nonlinear Encoding Quantization levels not evenly spaced
Reduces overall signal distortion
Can also be done by companding
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

46. Companding The process of compressing and then expanding.
The higher amplitude analog signals are compressed
prior to transmission and then expanded in receiver.
Improving the DR of a communication system.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

47. Companding Functions EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

48. Method of Companding
For the compression, two laws are adopted: the -law in US and Japan and the A-law in Europe.
-law
A-law
The typical values used in practice are: =255 and A=87.6.
After quantization the different quantized levels have to be represented in a form suitable for transmission. This is done via an encoding process.
Vmax= Max uncompressed analog input voltage
Vin= amplitude of the input signal at a particular of instant time
Vout= compressed output amplitude
A, = parameter define the amount of compression
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

49. Example 3
A companding system with µ = 255 used to compand from 0V to 15 V sinusoid signal. Draw the characteristic of the typical system.
Draw an 8 level non-uniform quantizer characteristic that corresponds to the mentioned µ.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

51. Cont’d... A-law μ-law EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

52. PCM Line Speed
Line speed is the data rate at which serial PCM bits are clocked out of the PCM encoder onto the transmission line.
Where
Line speed = the transmission rate in bits per second
Sample/second = sample rate, fs
Bits/sample = no of bits in the compressed PCM code
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

53. Example 4
For a single PCM system with a sample rate fs = 6000 samples per second and a 7 bits compressed PCM code, calculate the line speed.
ANS: (6000)(7)=42,000 bps.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

54. Virtues & Limitation of PCM
The most important advantages of PCM are:
Robustness to channel noise and interference.
Efficient regeneration of the coded signal along the channel path.
Efficient exchange between BT and SNR.
Uniform format for different kind of base-band signals.
Flexible TDM.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

55. Cont’d…
Secure communication through the use of special modulation schemes of encryption.
These advantages are obtained at the cost of more complexity and increased BT.
With cost-effective implementations, the cost issue no longer a problem of concern.
With the availability of wide-band communication channels and the use of sophisticated data compression techniques, the large bandwidth is not a serious problem.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

56. Time-Division Multiplexing
This technique combines time-domain samples from different message signals (sampled at the same rate) and transmits them together across the same channel.
The multiplexing is performed using a commutator (switch). At the receiver a decommutator (switch) is used in synchronism with the commutator to demultiplex the data.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

57. Cont’d…
TDM system is very sensitive to symbol dispersion, that is, to variation of amplitude with frequency or lack of proportionality of phase with frequency. This problem may be solved through equalization of both magnitude and phase.
One of the methods used to synchronize the operations of multiplexing and demultiplexing is to organize the multiplexed stream of data as frames with a special pattern. The pattern is known to the receiver and can be detected very easily.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

58. Block diagram of TDM-PCM communication system
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

59. DELTA MODULATION (DM)
Conventional PCM- multiple bit codes required to represent the sample value.
DM-Uses a single-bit PCM code to achieve digital transmission of analog signals.
Only encodes and transmits one bit per sample time
Logic ‘0’ is transmitted if current sample is smaller than the previous sample
Logic ‘1’ is transmitted if current sample is larger than the previous sample
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

60. Cont’d…
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

61. Operation of Delta Modulation
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

62. Cont’d... Analog input is approximated by a staircase function
Move up or down one level () at each sample interval (by one quantization level at each sampling time)  output of DM is a single bit.
Binary behavior
Function moves up or down at each sample interval
In DM the quantization levels are represented by two symbols: 0 for - and 1 for +. In fact the coding process is performed on eq.
The main advantage of DM is its simplicity.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

63. The transmitter of a DM System
Cont’d...
The transmitter of a DM System
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

64. The receiver of a DM system
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

65. Delta Modulation - Example
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

66. DM circuit’s problem Step size EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

67. Cont’d…
Slope overload distortion is due to the fact that the staircase approximation mq(t) can't follow closely the actual curve of the message signal m(t ). In contrast to slope-overload distortion, granular noise occurs when  is too large relative to the local slope characteristics of m(t). granular noise is similar to quantization noise in PCM.
It seems that a large  is needed for rapid variations of m(t). to reduce the slope-overload distortion and a small  is needed for slowly varying m(t) to reduce the granular noise. The optimum  can only be a compromise between the two cases.
To satisfy both cases, an adaptive DM is needed, where the step size  can be adjusted in accordance with the input signal m(t).
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

68. Cont’d... In summary Slope overload
Due to the input analog signal amplitude changes faster than the speed of the modulator
to minimize : the product of the sampling step size and the sampling rate must be equal to or larger than the rate of change of the amplitude of the input analog signal.
Granular noise
Due to the difference between step size and sampled voltage.
To minimize : increase the sampling rate, decrease the step size of modulator
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

69. DM Performance Good voice reproduction PCM - 128 levels (7 bit)
Voice bandwidth 4kHz
(line speed) Should be 8000 x 7 = 56kbps for PCM
Data compression can improve on this
e.g. Interframe coding techniques for video
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

70. Cont’d... Adaptive Delta Modulation (ADM)
A Delta Modulation system where the step size of the DAC is automatically varied depending on the amplitude characteristics of the analog signal.
A well designed ADM scheme can transmit voice at about half the bit rate of a PCM system with equivalent quality.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL MODULATION

71. LINE CODES The line codes properties: Line code is an encoding scheme.
Many possible ways to encode 0s and 1s.
Converting standard logic level to a form more suitable to telephone line transmission.
Different types of encoding schemes or line codes can be used to improve signal’s noise immunity and to achieve higher data rates.
The line codes properties:
Transmission BW should be small as possible
Efficiency should be as high as possible
Error detection & correction capability
Transparency (Encoded signal is received faithfully)
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

72. Cont’d...
Six factors must be considered when selecting a line encoding format;
Transmission voltage & DC component
Duty cycle
Bandwidth consideration
Clock and framing bit recovery
Error detection
Ease of detection and decoding
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

73. Why Digital Signaling? Low cost digital circuits
The flexibility of the digital approach (because digital data from digital sources may be merged with digitized data derived from analog sources to provide general purpose communication system)
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

74. Digital Encoding Using Digital Signals to Transmit Digital Data
Bits must be changed to digital signal for transmission
Unipolar encoding
Positive or negative pulse used for zero or one
Polar encoding
Uses two voltage levels (+ and - ) for zero or one
Bipolar encoding
+, -, and zero voltage levels are used
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

75. Non-Return to Zero-Level (NRZ-L)
Two different voltages for 0 and 1 bits.
Voltage constant during bit interval.
no transition, no return to zero voltage
More often, negative voltage for one value and positive for the other.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

76. Non-Return to Zero Inverted (NRZ-I)
Nonreturn to zero inverted on ones
Constant voltage pulse for duration of bit
Data encoded as presence or absence of signal transition at beginning of bit time
Transition (low to high or high to low) denotes a binary 1
No transition denotes binary 0
An example of differential encoding
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

77. Multilevel Binary (Bipolar-AMI)
zero represented by no line signal.
one represented by positive or negative pulse alternately.
No loss of sync if a long string of ones (zeros still a problem)
No net dc component
Lower bandwidth
Easy error detection
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

78. Pseudoternary One represented by absence of line signal
Zero represented by alternating positive and negative
No advantage or disadvantage over bipolar-AMI
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

79. Manchester
There is always a mid-bit transition {which is used as a clocking mechanism}.
The direction of the mid-bit transition represents the digital data.
1  low-to-high transition
0  high-to-low transition
Consequently, there may be a second transition at the beginning of the bit interval.
Used in baseband coaxial cable and CSMA/CD twisted pair.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

80. EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

81. Differential Manchester
mid-bit transition is ONLY for clocking.
1  absence of transition at the beginning of the bit interval
0  presence of transition at the beginning of the bit interval
Differential Manchester is both differential and bi-phase.
[Note – the coding is the opposite convention from NRZI.]
Used in (token ring) with twisted pair.
Modulation rate for Manchester and Differential Manchester is twice the data rate  inefficient encoding for long-distance applications.
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

82. EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

83. There is always a mid-bit transition, 1  low-to-high transition 0  high-to-low transition
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION
mid-bit transition is ONLY for clocking , 1  absence of transition 0  presence of transition

84. Example 5 Sketch the data wave form for a bit stream 11010 using NRZL
Bipolar AMI
Pseudoternary
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION

85. Solution

86. END DIGITAL TRANSMISSION
EKT 231 : COMMUNICATION SYSTEM
CHAPTER 4 : DIGITAL TRANSMISSION