1. How to configure PC Controlled Camera Control
PC Controlled Cam. Control

2. This presentation is intended to guide the installer step by step through the camera control installation.
PC Controlled Cam. Control

3. PC controlled DCN system with Camera Control
Direct Camera Control
With Allegiant Video Switcher
PC Controlled Cam. Control

4. Direct Camera Control (PC Controlled)
Requirements :
One Dome Camera
CCU with TCB4
One monitor
DCN software V9.30 or higher!!!
DCN Control PC = Temporary Installation PC
Software LBB3588/00 V2.0 or higher!!!
PC Controlled Cam. Control

5. Step 1 Connect PC and Monitor to Dome Camera
AutoDome
Camera
RS232
DCN Control PC
with one Comport
PC Controlled Cam. Control

6. Step 2 Install virtual keyboard software LTC 5138/00
Program
AutoDome
Camera
RS232
DCN Control PC
with one Comport
PC Controlled Cam. Control

7. Step 3 Configure Virtual Keyboard
PC Controlled Cam. Control

8. PC Controlled Cam. Control
PC Controlled Cam. Control

9. Make sure you choose the right camera!!
PC Controlled Cam. Control

10. PC Controlled Cam. Control
PC Controlled Cam. Control

11. PC Controlled Cam. Control
PC Controlled Cam. Control

12. PC Controlled Cam. Control
PC Controlled Cam. Control

13. Step 4 Set Pre-Positions
PC Controlled Cam. Control

14. PC Controlled Cam. Control
PC Controlled Cam. Control

15. Repeat Step 4 to set all Pre-Positions
Set the highest Pre-Position as overview
PC Controlled Cam. Control

16. Step 5 Check the Pre-Positions
PC Controlled Cam. Control

17. First make sure that the pre-positions are set.
If you were not successful setting up the pre-positions please don’t continue with the next steps.
First make sure that the pre-positions are set.
PC Controlled Cam. Control

18. Step 6 Connect CCU to DCN Control PC and AutoDome
Port 1
RS232
DCN Control PC
DCN CCU
Port 2
AutoDome
Camera
PC Controlled Cam. Control

19. Step 7 CCU protocol and Serial Port settings
LBB3500/15 & LBB3500/35
Make sure that the ports of the CCU are set correct.
Port 1 Protocol = Full Baudrate = 115.2K
Port 2 Protocol = Camera Control Baudrate = 9.6K
Keep in mind !!
You have to change the baudrate of Port 2 to 9.6K !!
PC Controlled Cam. Control

20. Step 8 Start Camera Control Software LBB3588
PC Controlled Cam. Control

21. Keep in mind !!
An installation file must be open before camera installation is possible.
PC Controlled Cam. Control

22. Step 9 Combine seat numbers with camera pre positions
PC Controlled Cam. Control

23. Keep in mind !!
Make sure you choose the right camera!! Camera nr = Camera Address
PC Controlled Cam. Control

24. PC Controlled Cam. Control
PC Controlled Cam. Control

25. 5
PC Controlled Cam. Control

26. End of Installation
© Robert Bosch GmbH reserves all rights even in the event of industrial
property rights. We reserve all rights of disposal such as copying and passing on to third parties.
PC Controlled Cam. Control

27. With use of Allegiant Video Switcher (PC Controlled DCN)
Requirements :
Allegiant switcher
Video Switcher keyboard
Fixed and/or AutoDome cameras
Monitor(s)
DCN software V8.00 or higher
DCN Control PC with two Comports
Software LBB3588 V1.0 or higher
PC Controlled Cam. Control

28. Step 1 Connect Camera(s),Monitor(s) and Keyboard to Video Switcher
PC Controlled Cam. Control

29. Step 2 Connect CCU to Allegiant Switcher and DCN Control PC
Port 1
RS232
DCN Control PC
DCN CCU
Port 2
Allegiant Switcher
PC Controlled Cam. Control

30. Step 3 CCU protocol and Serial Port settings
LBB3500/15 & LBB3500/35
Make sure that the following settings are chosen:
Port 1 Protocol = Full Baudrate = 115.2K
Port 2 Protocol = Camera Control Baudrate = 19.2K
Keep in mind !!
These are the default settings for the LBB3500/15 &LBB3500/35
PC Controlled Cam. Control

31. Step 4 Start Camera Control Software LBB3588
PC Controlled Cam. Control

32. Keep in mind !!
An installation file must be open before camera installation is possible.
PC Controlled Cam. Control

33. Step 5 Set Pre-Positions using the Video Switcher Keyboard
PC Controlled Cam. Control

34. Step 6 Combine seat numbers with camera pre positions
PC Controlled Cam. Control

35. PC Controlled Cam. Control
PC Controlled Cam. Control

36. 5
PC Controlled Cam. Control

37. How to configure PC Controlled Camera Control
End of section
 Robert Bosch GmbH
All rights are reserved. Reproduction or passing on to third parties in whole or in parts is prohibited without the written consent of the copyright owner.
PC Controlled Cam. Control