1. 影像強化(Image Enhancement)
影像強化：處理影像使其結果比原始影像更為適合某特定應用

2. 影像對比反轉(Contrast reversal)
PhotoImpact：影像調整反向
s = T(p) = 255 – p 41
214

3. 對比擴展:調亮
PhotoImpact：相片亮度與對比 41 58

4. 對比擴展:調暗
PhotoImpact：相片亮度與對比 41 12

5. 直方圖
PhotoImpact：調整高亮度中間值陰影

7. Roberts 濾波器 銳化濾波器(Sharpening filter) 增強影像細微部分、被模糊的細節、邊緣
PhotoImpact：相片  清晰 強調邊緣

8. Roberts 濾波器 Gx
0=50-50
0=70-70 F 50 70
-20
-20

9. Roberts 濾波器 Gy
20=70-50
20=70-50 F 50 70 20
-20
-20 20 20

10. Roberts 濾波器
F’ = F + Gx + Gy Gy 50 70 20
-20 Gx F
-20 70 90 50 30 10

11. Roberts 濾波器
F’ = F + Gx + Gy

12. Roberts 濾波器

13. Laplacian 濾波器 Lx 40=70+50+50+70-4*50 -40=70+80+50+50+70-4*70 F L 401 -4
40= *50
-40= *70 F L 50 70
-20 40
-40
-20 20 40
-40

14. Laplacian 濾波器
F’ = F - L

15. Vector Quantization (VQ)7 7 9 10
Index table
In this paper we based on vector quantization image compression scheme and Chinese remainder theorem to hide information.
The concept of the VQ is try to encode an image into a index table.
For example, assume there is a 4 by 4 image. And we want to compress the image by using VQ.
First, the image is divided into 2 by 2 blocks, each block of size 2 by 2.
Then each block maps a proper codeword from a codebook.
If the codeword has the minimum Euclidean distance with the block, then the block is compressed by the index of the codeword.
We can see the codeword 7 has the least distance with this block. So we use the corresponding index 7 to represent the block.
After VQ compression we can obtain a set of index called a index table.
Original Image
VQ Encoder

16. Vector Quantization (VQ)
Index table
Reconstructed Image
Then we can use a VQ decoder to reconstruct the original image.
When we want to reconstruct the original image, we just map the index in the index table to the corresponding codeword in the codebook. And the block is replace by the codeword. Then we can obtain the reconstructed image.
VQ Decoder

17. Vector Quantization (VQ)
Image compression technique 15 20 10 18 50 40 60 25
110
125
113
140 30
210
220
230
240
100 70 3 7 9
255 13 15 10 11 12 5 7 8 9
120
130 48 36
140
150 53 27 1 2 3 4 5
Image 6 7
Vector Quantization Encoder

18. VQ Encoding Index table Original Image Codebook … (120,155,…,80) 11 2 3 4 5 6 7 8 9 10 11 12 13 14 15
(90,135,…,120)
(100,125,…,150) …
Index table
Original Image
(49,117,…,25)
(50,42,…,98)
(20,65,…,110)
Codebook

19. PSNR 34 15 85 37 45 17 10 27 51 40 31 20 12 11 5 5 11 10 13 20 31 41 51 27 10 17 44 37 85 14 35
Image
Stego-Image
MSE =
=0.4375
General, we use two measurements to judge the performance of a information hiding scheme.
The first one is image quality of the stego image that is the similarity between the original cover image and the stego image.
If the hiding process will not cause too much distortion, then the scheme is good.
In this slide, we will show how to calculate the image quality of the stego image.
Here are the cover image and the stego image.
First we use mean square error (MSE) to calculate the difference between two images.
The equation is shown here.
Now, we compute the difference between two pixels in two image then squares the difference.
The summation of the differences is divided by the total number of the pixels.
Then we can get the average difference
After that, we inverse the MSE to compute the PSNR value.
In this example, the PSNR value of the stego image is
General speaking, people can not find any different between two image while the PSNR value is higher than 25.
So is very high PSNR value .
Another measurement is information payload, which shows how many information can be embedded in a pixel.
In LSB, each pixel can be used to hide one bit. So the payload of LSB is 1 bpp.
PSNR (Peak Signal to Noise Ratio) =
=51.72
Payload = 1 (bit per pixel, bpp)

20. Vector Quantization (VQ)
Index table
Then we can use a VQ decoder to reconstruct the original image.
When we want to reconstruct the original image, we just map the index in the index table to the corresponding codeword in the codebook. And the block is replace by the codeword. Then we can obtain the reconstructed image.
Reconstructed Image

21. import java.io.*;
import java.io.InputStream;
import java.io.OutputStream;
public class PSNR {
public static void main(String args[]) throws IOException
DataInputStream in = new DataInputStream(new FileInputStream("Lena512.raw"));
DataOutputStream ou = new DataOutputStream(new FileOutputStream("Lena512_v1.raw"));
int imgSize = 512;
int Lena [][] = new int [imgSize][imgSize];
int Lena_2 [][] = new int [imgSize][imgSize];
double mse = 0;
for(int i=0;i<imgSize;i++)
for(int j=0;j<imgSize;j++)
Lena [i][j] = (int) in.readUnsignedByte() ;
Lena_2 [i][j]= Lena [i][j];
ou.writeByte(Lena_2[i][j]);
mse += (Lena [i][j] - Lena_2 [i][j]) *(Lena [i][j] - Lena_2 [i][j]) ; }
mse = mse/imgSize/imgSize;
double psnr = 10.0*(Math.log(255.0*255.0/mse)/Math.log(10.0));
System.out.print("psnr = " + psnr);
in.close();
ou.close();