Presentation is loading. Please wait.

Presentation is loading. Please wait.

RPZ-II, RPZE-II ½” , ¾” , 1½”.

Published bySharyl Bethany Butler Modified over 6 years ago

Similar presentations

Presentation on theme: "RPZ-II, RPZE-II ½” , ¾” , 1½”."— Presentation transcript:

1 RPZ-II, RPZE-II ½” , ¾” , 1½”

2 Modification Overview
Production of the RPZ II began in 1996 for the ½” and ¾” sizes. The 1½” size was introduced in The body is smaller in size than the original version and the parts do not interchange. The lead free version (RPZE II) was introduced in 2002 and is current.

3 Single Access Cover Removal
The cover is spring loaded and sealed by the diaphragm. ** Hold cover firmly while removing bolts.

4 Single Access Cover Removal
Lift cover straight off. Remove RV stem assembly and spring from body.

5 Check Valve Removal Check valve modules.
Modules are o-ring sealed and secured by spring clips. Pinch together the exposed ends of the clip and pull away from module. ** Use adjustable pliers if necessary.

6 Check Valve Removal Once the spring clips are removed, the modules can be pulled straight out of the body. Check valves can be removed in any order.

7 Disassemble Check Valve
Check modules are spring loaded. Holding the module firmly, unscrew the stem from the disc holder. Place a wrench on the spring retainer and a wrench on the disc holder.

8 Check Disc Replacement
Once the module is disassembled, the disc holder, retainer and disc are free. Reassemble in reverse order.

9 Check Seat Removal The check seat is part of the module.
If the seat is damaged, the entire module must be replaced.

10 Check Valve Reassembly Notes
Lubricate o-rings. Push checks into body. Replace spring clips in reverse order.

11 RV Stem Removal The RV stem and spring are situated between the check valves and are free once the single access cover is removed.

12 RV Seat Removal Unless damaged there is no need to remove the seat.
The seat is pushed firmly into the body and is o-ring sealed.

13 RV Diaphragm Replacement
The diaphragm is located on the upper stem. Unscrew the RV piston from the stem. Reassemble in reverse order.

14 RV Disc Replacement The RV disc is located on the lower stem.
Unscrew the disc retainer from the RV stem. Reassemble in reverse order.

15 RV Reassembly Notes Center the spring over the RV seat.
Position the RV stem into the body. Lubricate plunger o-ring.

16 Single Access Reassembly Notes
Make sure the diaphragm does not block the test cock ports in the body. ** Place lid bolts in cover to help align the diaphragm correctly.

Download ppt "RPZ-II, RPZE-II ½” , ¾” , 1½”."

Similar presentations

RP-500 ½- 1. Modification Overview Production of the RP500 began in 2007 and is current. Production of the RP500 began in 2007 and is current.

RP-500 ½- 1. Modification Overview Production of the RP500 began in 2007 and is current. Production of the RP500 began in 2007 and is current.
RP4A 2½ – 6. Modification Overview Production of the RP4A series began in 2008. Production of the RP4A series began in 2008. A Lead free version (4ALF)

RP4A 2½ – 6. Modification Overview Production of the RP4A series began in Production of the RP4A series began in A Lead free version (4ALF)
RP4AN 21/2 – 6. Modification Overview Production of the RP4AN series began in 2008. Production of the RP4AN series began in 2008. The 4AN indicates an.

RP4AN 21/2 – 6. Modification Overview Production of the RP4AN series began in Production of the RP4AN series began in The 4AN indicates an.
40-200 ¾”-2”. Modification Overview  Production of the 40-200 series began in 1989 and is current.  Early models of ¾”-2” 40-200 series did not always.

¾”-2”. Modification Overview  Production of the series began in 1989 and is current.  Early models of ¾”-2” series did not always.
RPDA 4A 2½” – 6”. Modification Overview  Production of the RPDA 4A series began in 2008.  The RPDA 4A can utilize either a Type I or Type II bypass.

RPDA 4A 2½” – 6”. Modification Overview  Production of the RPDA 4A series began in  The RPDA 4A can utilize either a Type I or Type II bypass.
860 (LF), 880 ½”- 2” 860 (LF), 880 ½”- 2”. Modification Overview  Production of the ½ - 2” 860 series began in 1997 and is current.  The 880 is an “N”

860 (LF), 880 ½”- 2” 860 (LF), 880 ½”- 2”. Modification Overview  Production of the ½ - 2” 860 series began in 1997 and is current.  The 880 is an “N”
860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in 1993.  Lead free version (LF860) was introduced in 2011. Parts do not.

860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in  Lead free version (LF860) was introduced in Parts do not.
350, 350A 2½”-12”. Modification Overview  Production of the 2½ - 10” sizes began in 1998.  Production of the “A” models began in 2004. This Indicates.

350, 350A 2½”-12”. Modification Overview  Production of the 2½ - 10” sizes began in  Production of the “A” models began in This Indicates.
975, 975XL ¾”-2” 975, 975XL ¾”-2”. Modification Overview  Production of the original 975 began in 1990. This version had buna-n check discs and did not.

975, 975XL ¾”-2” 975, 975XL ¾”-2”. Modification Overview  Production of the original 975 began in This version had buna-n check discs and did not.
975DA 2½”-10”. Modification Overview  Production of the 975DA began in 1993 and was discontinued in 2004.  The 975DA uses a ¾” 975XL for the bypass.

975DA 2½”-10”. Modification Overview  Production of the 975DA began in 1993 and was discontinued in  The 975DA uses a ¾” 975XL for the bypass.
825Y(YA) 3/4”-2”. Modification Overview  Production of the 825Y began in 1978 and is current.  The 825YR (1994-2006) had replaceable check seats. **

825Y(YA) 3/4”-2”. Modification Overview  Production of the 825Y began in 1978 and is current.  The 825YR ( ) had replaceable check seats. **
375AST 21/2”-10”. Modification Overview  The stainless steel (ST) series was introduced in 2011.  This version has a stainless steel body. ***(Parts.

375AST 21/2”-10”. Modification Overview  The stainless steel (ST) series was introduced in  This version has a stainless steel body. ***(Parts.
375, 375XL ¾”-1”. Modification Overview  Production of the ¾”-1” 375 began in 2004 and is current.  The lead free version 375XL was introduced in 2010.

375, 375XL ¾”-1”. Modification Overview  Production of the ¾”-1” 375 began in 2004 and is current.  The lead free version 375XL was introduced in 2010.
475, 475V 2½”-3”. Modification Overview  Production of the 2½ - 3” sizes began in 1998.  The lead free version (XL) was introduced in 2011.

475, 475V 2½”-3”. Modification Overview  Production of the 2½ - 3” sizes began in  The lead free version (XL) was introduced in 2011.
4D-200, 4D-700 2½”- 10”. Modification Overview  Production began in 2003 and was discontinued in 2009.  The 4D-700 (RPDA) uses a Type-II bypass (single.

4D-200, 4D-700 2½”- 10”. Modification Overview  Production began in 2003 and was discontinued in  The 4D-700 (RPDA) uses a Type-II bypass (single.
40-200 2½”-10”. Modification Overview  Production of the 40-200 series began in 1989 and is current.

½”-10”. Modification Overview  Production of the series began in 1989 and is current.
009 (M3) ½”-2” 009 (M3) ½”-2”. Modification Overview- 009  009 ¾-1” (1989-1991) (1” 1989-1997) ¾-1” (1989-1991) (1” 1989-1997) 1¼ -2” (1989-1991) 1¼.

009 (M3) ½”-2” 009 (M3) ½”-2”. Modification Overview- 009  009 ¾-1” ( ) (1” ) ¾-1” ( ) (1” ) 1¼ -2” ( ) 1¼.
RPZ 2½”- 10” RPZ 2½”- 10”. Modification Overview  Production of the RPZ in sizes 2½ - 10” began in 1993 and is current.

RPZ 2½”- 10” RPZ 2½”- 10”. Modification Overview  Production of the RPZ in sizes 2½ - 10” began in 1993 and is current.
5000CIV 21/2”-10” 5000CIV 21/2”-10”. Modification Overview  Production of the 5000CIV (Watts 909RPDA) began in 1998 and is current.  The 5000CIV utilizes.

5000CIV 21/2”-10” 5000CIV 21/2”-10”. Modification Overview  Production of the 5000CIV (Watts 909RPDA) began in 1998 and is current.  The 5000CIV utilizes.
375, 375XL 1¼” -2”. Modification Overview  Production of the 1¼” -2” 375 began in 2004 and is current.  The lead free version 375XL was introduced in.

375, 375XL 1¼” -2”. Modification Overview  Production of the 1¼” -2” 375 began in 2004 and is current.  The lead free version 375XL was introduced in.

Similar presentations

Ads by Google