1. WELCOME

2. E9
E9A Basic antenna parameters: radiation resistance, gain, beamwidth, efficiency, beamwidth; effective radiated power, polarization

3. Antenna Gain
Antenna gain is one of the most misunderstood topics in amateur radio. There are several reasons for this, including:
Antennas don’t really have gain in the same way that an amplifier has gain.
When you use a linear amplifier, you get more power out than you put in. Since transmitting antennas are passive devices, there’s no way to get more power out than you put in.
It’s not easy to measure antenna gain. There is no antenna gain meter that you can simply hook up to an antenna to measure its gain.

4. Antenna Gain So, what is meant by antenna gain?
Antenna gain is the ratio of the radiated signal strength of an antenna in the direction of maximum radiation to that of a reference antenna. (E9A07)
What this means is that when you talk about antenna gain, you have to know what kind of antenna you’re comparing it to.

5. Antenna Gain
When talking about antenna gain, antenna engineers often refer to the “isotropic antenna.”
An isotropic antenna is a theoretical antenna used as a reference for antenna gain. (E9A01)
An isotropic antenna is an antenna that has no gain in any direction. (E9A02)
That is to say it radiates the power input to it equally well in all directions

6. Antenna Gain Let’s take a look at a practical example.
I often say that the 1/2-wavelength dipole antenna is the most basic amateur radio antenna.
Well, the dipole actually has some gain over isotropic antenna. The reason for this is that it is directional.
The signal strength transmitted broadside to the antenna will be greater than the signal strength transmitted off the ends of the antenna.
The gain of a 1/2-wavelength dipole in free space have compared to an isotropic antenna is 2.15 dB.
Sometimes, you’ll see this value as 2.15 dBi, where dBi denotes that an isotropic antenna is being used for this comparison.

7. Antenna Gain
Since the isotropic antenna is a theoretical antenna, some think it’s better to compare an antenna to a dipole antenna.
An antenna will have a gain 3.85 dB compared to a 1/2-wavelength dipole when it has 6 dB gain over an isotropic antenna. (E9A12)
You obtain this value by simply subtracting dB from the 6 dB figure:
Gain over a dipole = gain over an isotropic antenna – 2.15 dB = 6 dBi – 2.15 dBi = 3.85 dBd

8. Antenna Gain Sometimes, the gain over a dipole is denoted as dBd.
Similarly, an antenna has a gain of 9.85 dB compared to a 1/2-wavelength dipole when it has 12 dB gain over an isotropic antenna. (E9A13):
Gain over a dipole = gain over an isotropic antenna – 2.15 dB = 12 dBi – 2.15 dBi = 9.85 dBd

9. Antenna Gain
Antennas that are said to have gain are really focusing the energy that are input to them.
The higher the gain, the narrower the focus, or beamwidth.
The beamwidth of an antenna decreases as the gain is increased. (E9A06)

10. Effective radiated power
When you use an antenna that has gain, you are increasing the effectiveness of the power input to it, at least in the direction the antenna is pointing.
The term that describes station output, taking into account all gains and losses is effective radiated power. (E9A18)
The effective radiated power is not just the input power times the gain of the antenna. You also have to take into account losses in other parts of the antenna system.

11. Antenna Gain
This is especially true for VHF and UHF repeater systems, where losses in the feedline, duplexer, and circulator can be significant.
The power that reaches the antenna may be substantially lower than the power output of the transmitter.

12. Antenna Gain
For example, the effective radiated power relative to a dipole of a repeater station with 150 watts transmitter power output, 2 dB feed line loss, 2.2 dB duplexer loss, and 7 dBd antenna gain is 286 watts. (E9A15)
To calculate the answer, you have to first subtract the losses from the gain, as expressed in dB to get the total gain of the system:
total system gain = 7 dB – 2 dB – 2.2 dB = 2.8 dB.
2.8 dB corresponds to a power ratio of approximately , so the effective radiated power is the transmitter output power times the total system gain:
effective radiated power = 150 W x = 268 W.

13. Antenna Gain
The effective radiated power relative to a dipole of a repeater station with 200 watts transmitter power output, 4 dB feed line loss, 3.2 dB duplexer loss, 0.8 dB circulator loss, and 10 dBd antenna gain is 317 watts. (E9A16).
In this case, the total gain of the system is 10 dB – 4 dB – 3.2 dB – 0.8 dB, or 2.0 dB. 2.0 dB corresponds to a power ratio of approximately 1.585
The effective radiated power; 200 W x = 317 W.
In this system, high feedline and duplexer losses are almost completely negating the benefit of using such a high gain antenna.

14. Antenna Gain
Finally, the effective radiated power of a repeater station with 200 watts transmitter power output, 2 dB feed line loss, 2.8 dB duplexer loss, 1.2 dB circulator loss, and 7 dBi antenna gain is 252 watts. (E9A17)
In this example, the total gain of the system is 7 dB – 2 dB – 2.8 dB – 1.2 dB, or 1.0 dB dB corresponds to a power ratio of approximately 1.26,
The effective radiated power equals 200 W x = 252 W.

15. Antenna Gain Other antenna parameters are also important, of course.
One of the most basic antenna parameters is the feed point impedance.
Why would one need to know the feed point impedance of an antenna? 
To match impedances in order to minimize standing wave ratio on the transmission line. (E9A03) The reason that it’s important to minimize the standing wave ratio, or SWR, is that if you’re using coaxial cables, minimizing the SWR will also help you minimize losses. If you minimize losses, you’ll radiate more signal.

16. Feed Point Impedance
Many factors may affect the feed point impedance of an antenna, including antenna height, conductor length/diameter ratio and location of nearby conductive objects. (E9A04)
For example, we say that the feed point impedance of a half-wavelength, dipole antenna is 72 Ω, but that’s only really true if the antenna is in free space.
When it’s closer to the ground than a quarter wavelength, then the impedance will be different. That’s why you have to tune the antenna when you install it.

17. Feed Point Impedance
Another antenna parameter that’s frequently discussed is radiation resistance.
The radiation resistance of an antenna is the value of a resistance that would dissipate the same amount of power as that radiated from an antenna. (E9A14) 
Radiation resistance plus ohmic resistance is included in the total resistance of an antenna system. (E9A05)

18. Feed Point Impedance
If you know the radiation resistance and the ohmic resistance of an antenna, you can calculate its efficiency.
You calculate antenna efficiency with the formula (radiation resistance / total resistance) x 100 percent. (E9A09)

19. Vertical Antennas
Vertical antennas are sometimes criticized as being inefficient antennas. 
Soil conductivity is one factor that determines ground losses for a ground-mounted vertical antenna operating in the 3-30 MHz range. (E9A11)
If soil conductivity is poor, ohmic resistance will be high.
One way to improve the efficiency of a ground- mounted quarter-wave vertical antenna is to install a good radial system. (E9A10)

20. Antenna Bandwidth
The frequency range over which an antenna satisfies a performance requirement is called antenna bandwidth. (E9A08)
Normally, the performance requirement is an SWR of 2:1 or less. In fact, you’ll sometimes hear this parameter referred to as the 2:1 SWR bandwidth.

21. E9A01 | What describes an isotropic antenna?
A. A grounded antenna used to measure earth conductivity
B. A horizontally polarized antenna used to compare Yagi antennas
C. A theoretical antenna used as a reference for antenna gain
D. A spacecraft antenna used to direct signals toward the earth

22. E9A01 (C) | What describes an isotropic antenna?
A. A grounded antenna used to measure earth conductivity
B. A horizontally polarized antenna used to compare Yagi antennas
C. A theoretical antenna used as a reference for antenna gain
D. A spacecraft antenna used to direct signals toward the earth

23. E9A02 | What antenna has no gain in any direction?
A. Quarter-wave vertical
B. Yagi
C. Half-wave dipole
D. Isotropic antenna

24. E9A02 (D) | What antenna has no gain in any direction?
A. Quarter-wave vertical
B. Yagi
C. Half-wave dipole
D. Isotropic antenna

25. E9A03 | Why would one need to know the feed point impedance of an antenna?
A. To match impedances in order to minimize standing wave ratio on the transmission line
B. To measure the near-field radiation density from a transmitting antenna
C. To calculate the front-to-side ratio of the antenna
D. To calculate the front-to-back ratio of the antenna

26. E9A03 (A) | Why would one need to know the feed point impedance of an antenna?
A. To match impedances in order to minimize standing wave ratio on the transmission line
B. To measure the near-field radiation density from a transmitting antenna
C. To calculate the front-to-side ratio of the antenna
D. To calculate the front-to-back ratio of the antenna

27. E9A04 | Which of the following factors may affect the feed point impedance of an antenna?
A. Transmission-line length
B. Antenna height, conductor length/diameter ratio and location of nearby conductive objects
C. The settings of an antenna tuner at the transmitter
D. Sunspot activity and time of day

28. E9A04 (B) | Which of the following factors may affect the feed point impedance of an antenna?
A. Transmission-line length
B. Antenna height, conductor length/diameter ratio and location of nearby conductive objects
C. The settings of an antenna tuner at the transmitter
D. Sunspot activity and time of day

29. E9A05 | What is included in the total resistance of an antenna system?
A. Radiation resistance plus space impedance
B. Radiation resistance plus transmission resistance
C. Transmission-line resistance plus radiation resistance
D. Radiation resistance plus ohmic resistance

30. E9A05 (D) | What is included in the total resistance of an antenna system?
A. Radiation resistance plus space impedance
B. Radiation resistance plus transmission resistance
C. Transmission-line resistance plus radiation resistance
D. Radiation resistance plus ohmic resistance

31. E9A06 | How does the beamwidth of an antenna vary as the gain is increased?
A. It increases geometrically
B. It increases arithmetically
C. It is essentially unaffected
D. It decreases

32. E9A06 (D) | How does the beamwidth of an antenna vary as the gain is increased?
A. It increases geometrically
B. It increases arithmetically
C. It is essentially unaffected
D. It decreases

33. E9A07 | What is meant by antenna gain?
A. The ratio of the radiated signal strength of an antenna in the direction of maximum radiation to that of a reference antenna
B. The ratio of the signal in the forward direction to that in the opposite direction
C. The ratio of the amount of power radiated by an antenna compared to the transmitter output power
D. The final amplifier gain minus the transmission line

34. E9A07 (A) | What is meant by antenna gain?
A. The ratio of the radiated signal strength of an antenna in the direction of maximum radiation to that of a reference antenna
B. The ratio of the signal in the forward direction to that in the opposite direction
C. The ratio of the amount of power radiated by an antenna compared to the transmitter output power
D. The final amplifier gain minus the transmission line

35. E9A08 | What is meant by antenna bandwidth?
A. Antenna length divided by the number of elements
B. The frequency range over which an antenna satisfies a performance requirement
C. The angle between the half-power radiation points
D. The angle formed between two imaginary lines drawn through the element ends

36. E9A08 (B) | What is meant by antenna bandwidth?
A. Antenna length divided by the number of elements
B. The frequency range over which an antenna satisfies a performance requirement
C. The angle between the half-power radiation points
D. The angle formed between two imaginary lines drawn through the element ends

37. E9A09 | How is antenna efficiency calculated?
A. (radiation resistance / transmission resistance) x 100 per cent
B. (radiation resistance / total resistance) x 100 per cent
C. (total resistance / radiation resistance) x 100 per cent
D. (effective radiated power / transmitter output) x 100 percent

38. E9A09 (B) | How is antenna efficiency calculated?
A. (radiation resistance / transmission resistance) x 100 per cent
B. (radiation resistance / total resistance) x 100 per cent
C. (total resistance / radiation resistance) x 100 per cent
D. (effective radiated power / transmitter output) x 100 percent

39. E9A10 | Which of the following choices is a way to improve the efficiency of a ground-mounted quarter-wave vertical antenna?
A. Install a good radial system
B. Isolate the coax shield from ground
C. Shorten the radiating element
D. Reduce the diameter of the radiating element

40. E9A10 (A) | Which of the following choices is a way to improve the efficiency of a ground-mounted quarter-wave vertical antenna?
A. Install a good radial system
B. Isolate the coax shield from ground
C. Shorten the radiating element
D. Reduce the diameter of the radiating element

41. E9A11 | Which of the following factors determines ground
losses for a ground-mounted vertical antenna operating in the 3 MHz to 30 MHz range?
A. The standing wave ratio
B. Distance from the transmitter
C. Soil conductivity
D. Take-off angle

42. E9A11 (C) | Which of the following factors determines ground losses for a ground-mounted vertical antenna operating in the 3 MHz to 30 MHz range?
A. The standing wave ratio
B. Distance from the transmitter
C. Soil conductivity
D. Take-off angle

43. E9A12 | How much gain does an antenna have compared to a 1/2-wavelength dipole when it has 6 dB gain over an isotropic antenna?
A dB
B. 6.0 dB
C dB
D dB

44. E9A12 (A) | How much gain does an antenna have compared to a 1/2-wavelength dipole when it has 6 dB gain over an isotropic antenna?
A dB
B. 6.0 dB
C dB
D dB

45. E9A13 | How much gain does an antenna have compared to a 1/2-wavelength dipole when it has 12 dB gain over an isotropic antenna?
A dB
B dB
C dB
D dB

46. E9A13 (B) | How much gain does an antenna have compared to a 1/2-wavelength dipole when it has 12 dB gain over an isotropic antenna?
A dB
B dB
C dB
D dB

47. E9A14 | What is meant by the radiation resistance of an antenna?
A. The combined losses of the antenna elements and feed line
B. The specific impedance of the antenna
C. The value of a resistance that would dissipate the same amount of power as that radiated from an antenna
D. The resistance in the atmosphere that an antenna must overcome to be able to radiate a signal

48. E9A14 (C) | What is meant by the radiation resistance of an antenna?
A. The combined losses of the antenna elements and feed line
B. The specific impedance of the antenna
C. The value of a resistance that would dissipate the same amount of power as that radiated from an antenna
D. The resistance in the atmosphere that an antenna must overcome to be able to radiate a signal

49. E9A15 | What is the effective radiated power relative to a
dipole of a repeater station with 150 watts transmitter power output, 2 dB feed line loss, 2.2 dB duplexer loss, and 7 dBd antenna gain?
A watts
B watts
C. 420 watts
D. 286 watts

50. E9A15 (D) | What is the effective radiated power relative to a dipole of a repeater station with 150 watts transmitter power output, 2 dB feed line loss, 2.2 dB duplexer loss, and 7 dBd antenna gain?
A watts
B watts
C. 420 watts
D. 286 watts

51. E9A16 | What is the effective radiated power relative to a
dipole of a repeater station with 200 watts transmitter power output, 4 dB feed line loss, 3.2 dB duplexer loss, 0.8 dB circulator loss, and 10 dBd antenna gain?
A. 317 watts
B watts
C. 126 watts
D. 300 watts

52. E9A16 (A) | What is the effective radiated power relative to a dipole of a repeater station with 200 watts transmitter power output, 4 dB feed line loss, 3.2 dB duplexer loss, 0.8 dB circulator loss, and 10 dBd antenna gain?
A. 317 watts
B watts
C. 126 watts
D. 300 watts

53. E9A17 | What is the effective radiated power of a repeater
station with 200 watts transmitter power output, 2 dB feed line loss, 2.8 dB duplexer loss, 1.2 dB circulator loss, and 7 dBi antenna gain?
A. 159 watts
B. 252 watts
C. 632 watts
D watts

54. E9A17 (B) | What is the effective radiated power of a repeater station with 200 watts transmitter power output, 2 dB feed line loss, 2.8 dB duplexer loss, 1.2 dB circulator loss, and 7 dBi antenna gain?
A. 159 watts
B. 252 watts
C. 632 watts
D watts

55. E9A18 | What term describes station output, taking into account all gains and losses?
A. Power factor
B. Half-power bandwidth
C. Effective radiated power
D. Apparent power

56. E9A18 (C) | What term describes station output, taking into account all gains and losses?
A. Power factor
B. Half-power bandwidth
C. Effective radiated power
D. Apparent power

57. E9A
E9B – Antenna patterns: E and H plane patterns; gain as a function of pattern; antenna design

58. Antenna Patterns
Many amateurs use directional antennas because they are said to have “gain.”
When this term is used, what it means is that a directional antenna will output more power in a particular direction than an antenna that is not directional.
This only makes sense; You can’t get more power out of an antenna than you put in. Assuming each is driven by the same amount of power, the total amount of radiation emitted by a directional gain antenna compared with the total amount of radiation emitted from an isotropic antenna is the same. (E9B07)

59. Antenna Patterns
To evaluate the performance of directional antennas, manufacturers will measure the field strength at various points in a circle around the antenna and plot those field strengths, creating a chart called the azimuth antenna radiation pattern.

60. Antenna Patterns
Figure E9-1 is a typical azimuth antenna radiation pattern.

61. Antenna Patterns
The antenna radiation pattern shows the relative strength of the signal generated by an antenna in its “far field.” The far-field of an antenna is the region where the shape of the antenna pattern is independent of distance. (E9B12)
From the antenna radiation pattern, we can tell a bunch of things about the antenna.
One of them is beamwidth. Beamwidth is a measure of the width of the main lobe of the radiation pattern.
To determine the approximate beamwidth in a given plane of a directional antenna, note the two points where the signal strength of the antenna is 3 dB less than maximum and compute the angular difference. (E9B08)

62. Antenna Patterns
In the antenna radiation pattern shown in Figure E9- 1, 50 degrees is the 3-dB beamwidth. (E9B01)

63. Antenna Patterns
Another parameter that’s important for a directional antenna is the front-to-back ratio.
In a sense, this is a measure of how directional an antenna really is.
The higher this ratio, the more directional the antenna.

64. Antenna Patterns
In the antenna radiation pattern shown in Figure E9- 1, 18 dB is the front-to-back ratio. (E9B02)

65. Antenna Patterns
A similar parameter is the front-to-side ratio. In the antenna radiation pattern shown in Figure E9-1, the front-to-side ratio is 14 dB. (E9B03)

66. Antenna Patterns
When reviewing an antenna radiation pattern, you need to remember that the field strength measurements were taken at a particular frequency.
When a directional antenna is operated at different frequencies within the band for which it was designed, the gain may change depending on frequency. (E9B04)
Many different design factors affect these antenna parameters.
For example, if the boom of a Yagi antenna is lengthened and the elements are properly retuned, what usually occurs is that the gain increases. (E9B06)

67. Antenna Patterns
Because antennas radiate in three dimensions, the azimuth antenna pattern tells only part of the story.
To get a complete picture of antenna performance, you also want to know what the antenna pattern is in the vertical direction.
This type of pattern is called the elevation antenna pattern.

68. Antenna Patterns
An elevation antenna patter over real ground is show in Figure E9-2. (E9B05)

69. Antenna Patterns
In the antenna radiation pattern shown in Figure E9- 2, 4 elevation lobes appear in the forward direction. (E9B16)

70. Antenna Patterns
In the antenna radiation pattern shown in Figure E9-2, the elevation angle of peak response in is 7.5 degrees. (E9B06)

71. Antenna Patterns
The front-to-back ratio of the radiation pattern shown in Figure E9-2 is 28 dB. (E9B15)

72. Antenna design
To help design antennas, many amateurs use antenna modeling programs. 
All of these choices are correct when talking about the information obtained by submitting the details of a proposed new antenna to a modeling program (E9B14):
SWR vs. frequency charts
Polar plots of the far-field elevation and azimuth patterns
Antenna gain

73. Method of Moments
The type of computer program technique commonly used for modeling antennas is method of moments. (E9B09)
The principle behind a method of moments analysis is that a wire is modeled as a series of segments, each having a uniform value of current. (E9B10)

74. Method of Moments
The more segments your simulation uses, the more accurate the results.
The problem with using too many segments, though, is that the program will take a very long time to run. You don’t want to use too few segments, though.
A disadvantage of decreasing the number of wire segments in an antenna model below the guideline of 10 segments per half-wavelength is that the computed feed point impedance may be incorrect. (E9B11)

75. Numerical Electromagnetics Code
The abbreviation NEC stands for Numerical Electromagnetics Code when applied to antenna modeling programs. (E9B13)
This is different from the more common definition of NEC, which is the National Electrical Code.

76. E9A01 | What describes an isotropic antenna?
A. A grounded antenna used to measure earth conductivity
B. A horizontally polarized antenna used to compare Yagi antennas
C. A theoretical antenna used as a reference for antenna gain
D. A spacecraft antenna used to direct signals toward the earth

77. E9A01 (C) | What describes an isotropic antenna?
A. A grounded antenna used to measure earth conductivity
B. A horizontally polarized antenna used to compare Yagi antennas
C. A theoretical antenna used as a reference for antenna gain
D. A spacecraft antenna used to direct signals toward the earth

78. E9A02 | What antenna has no gain in any direction?
A. Quarter-wave vertical
B. Yagi
C. Half-wave dipole
D. Isotropic antenna

79. E9A02 (D) | What antenna has no gain in any direction?
A. Quarter-wave vertical
B. Yagi
C. Half-wave dipole
D. Isotropic antenna

80. E9A03 | Why would one need to know the feed point impedance of an antenna?
A. To match impedances in order to minimize standing wave ratio on the transmission line
B. To measure the near-field radiation density from a transmitting antenna
C. To calculate the front-to-side ratio of the antenna
D. To calculate the front-to-back ratio of the antenna

81. E9A03 (A) | Why would one need to know the feed point impedance of an antenna?
A. To match impedances in order to minimize standing wave ratio on the transmission line
B. To measure the near-field radiation density from a transmitting antenna
C. To calculate the front-to-side ratio of the antenna
D. To calculate the front-to-back ratio of the antenna

82. E9A04 | Which of the following factors may affect the feed point impedance of an antenna?
A. Transmission-line length
B. Antenna height, conductor length/diameter ratio and location of nearby conductive objects
C. The settings of an antenna tuner at the transmitter
D. Sunspot activity and time of day

83. E9A04 (B) | Which of the following factors may affect the feed point impedance of an antenna?
A. Transmission-line length
B. Antenna height, conductor length/diameter ratio and location of nearby conductive objects
C. The settings of an antenna tuner at the transmitter
D. Sunspot activity and time of day

84. E9A05 | What is included in the total resistance of an antenna system?
A. Radiation resistance plus space impedance
B. Radiation resistance plus transmission resistance
C. Transmission-line resistance plus radiation resistance
D. Radiation resistance plus ohmic resistance

85. E9A05 (D) | What is included in the total resistance of an antenna system?
A. Radiation resistance plus space impedance
B. Radiation resistance plus transmission resistance
C. Transmission-line resistance plus radiation resistance
D. Radiation resistance plus ohmic resistance

86. E9A06 | How does the beamwidth of an antenna vary as the gain is increased?
A. It increases geometrically
B. It increases arithmetically
C. It is essentially unaffected
D. It decreases

87. E9A06 (D) | How does the beamwidth of an antenna vary as the gain is increased?
A. It increases geometrically
B. It increases arithmetically
C. It is essentially unaffected
D. It decreases

88. E9A07 | What is meant by antenna gain?
A. The ratio of the radiated signal strength of an antenna in the direction of maximum radiation to that of a reference antenna
B. The ratio of the signal in the forward direction to that in the opposite direction
C. The ratio of the amount of power radiated by an antenna compared to the transmitter output power
D. The final amplifier gain minus the transmission line

89. E9A07 (A) | What is meant by antenna gain?
A. The ratio of the radiated signal strength of an antenna in the direction of maximum radiation to that of a reference antenna
B. The ratio of the signal in the forward direction to that in the opposite direction
C. The ratio of the amount of power radiated by an antenna compared to the transmitter output power
D. The final amplifier gain minus the transmission line

90. E9A08 | What is meant by antenna bandwidth?
A. Antenna length divided by the number of elements
B. The frequency range over which an antenna satisfies a performance requirement
C. The angle between the half-power radiation points
D. The angle formed between two imaginary lines drawn through the element ends

91. E9A08 (B) | What is meant by antenna bandwidth?
A. Antenna length divided by the number of elements
B. The frequency range over which an antenna satisfies a performance requirement
C. The angle between the half-power radiation points
D. The angle formed between two imaginary lines drawn through the element ends

92. E9A09 | How is antenna efficiency calculated?
A. (radiation resistance / transmission resistance) x 100 per cent
B. (radiation resistance / total resistance) x 100 per cent
C. (total resistance / radiation resistance) x 100 per cent
D. (effective radiated power / transmitter output) x 100 percent

93. E9A09 (B) | How is antenna efficiency calculated?
A. (radiation resistance / transmission resistance) x 100 per cent
B. (radiation resistance / total resistance) x 100 per cent
C. (total resistance / radiation resistance) x 100 per cent
D. (effective radiated power / transmitter output) x 100 percent

94. E9A10 | Which of the following choices is a way to improve the efficiency of a ground-mounted quarter-wave vertical antenna?
A. Install a good radial system
B. Isolate the coax shield from ground
C. Shorten the radiating element
D. Reduce the diameter of the radiating element

95. E9A10 (A) | Which of the following choices is a way to improve the efficiency of a ground-mounted quarter-wave vertical antenna?
A. Install a good radial system
B. Isolate the coax shield from ground
C. Shorten the radiating element
D. Reduce the diameter of the radiating element

96. E9A11 | Which of the following factors determines ground
losses for a ground-mounted vertical antenna operating in the 3 MHz to 30 MHz range?
A. The standing wave ratio
B. Distance from the transmitter
C. Soil conductivity
D. Take-off angle

97. E9A11 (C) | Which of the following factors determines ground losses for a ground-mounted vertical antenna operating in the 3 MHz to 30 MHz range?
A. The standing wave ratio
B. Distance from the transmitter
C. Soil conductivity
D. Take-off angle

98. E9A12 | How much gain does an antenna have compared to a 1/2-wavelength dipole when it has 6 dB gain over an isotropic antenna?
A dB
B. 6.0 dB
C dB
D dB

99. E9A12 (A) | How much gain does an antenna have compared to a 1/2-wavelength dipole when it has 6 dB gain over an isotropic antenna?
A dB
B. 6.0 dB
C dB
D dB

100. E9A13 | How much gain does an antenna have compared to a 1/2-wavelength dipole when it has 12 dB gain over an isotropic antenna?
A dB
B dB
C dB
D dB

101. E9A13 (B) | How much gain does an antenna have compared to a 1/2-wavelength dipole when it has 12 dB gain over an isotropic antenna?
A dB
B dB
C dB
D dB

102. E9A14 | What is meant by the radiation resistance of an antenna?
A. The combined losses of the antenna elements and feed line
B. The specific impedance of the antenna
C. The value of a resistance that would dissipate the same amount of power as that radiated from an antenna
D. The resistance in the atmosphere that an antenna must overcome to be able to radiate a signal

103. E9A14 (C) | What is meant by the radiation resistance of an antenna?
A. The combined losses of the antenna elements and feed line
B. The specific impedance of the antenna
C. The value of a resistance that would dissipate the same amount of power as that radiated from an antenna
D. The resistance in the atmosphere that an antenna must overcome to be able to radiate a signal

104. E9A15 | What is the effective radiated power relative to a
dipole of a repeater station with 150 watts transmitter power output, 2 dB feed line loss, 2.2 dB duplexer loss, and 7 dBd antenna gain?
A watts
B watts
C. 420 watts
D. 286 watts

105. E9A15 (D) | What is the effective radiated power relative to a dipole of a repeater station with 150 watts transmitter power output, 2 dB feed line loss, 2.2 dB duplexer loss, and 7 dBd antenna gain?
A watts
B watts
C. 420 watts
D. 286 watts

106. E9A16 | What is the effective radiated power relative to a
dipole of a repeater station with 200 watts transmitter power output, 4 dB feed line loss, 3.2 dB duplexer loss, 0.8 dB circulator loss, and 10 dBd antenna gain?
A. 317 watts
B watts
C. 126 watts
D. 300 watts

107. E9A16 (A) | What is the effective radiated power relative to a dipole of a repeater station with 200 watts transmitter power output, 4 dB feed line loss, 3.2 dB duplexer loss, 0.8 dB circulator loss, and 10 dBd antenna gain?
A. 317 watts
B watts
C. 126 watts
D. 300 watts

108. E9A17 | What is the effective radiated power of a repeater
station with 200 watts transmitter power output, 2 dB feed line loss, 2.8 dB duplexer loss, 1.2 dB circulator loss, and 7 dBi antenna gain?
A. 159 watts
B. 252 watts
C. 632 watts
D watts

109. E9A17 (B) | What is the effective radiated power of a repeater station with 200 watts transmitter power output, 2 dB feed line loss, 2.8 dB duplexer loss, 1.2 dB circulator loss, and 7 dBi antenna gain?
A. 159 watts
B. 252 watts
C. 632 watts
D watts

110. E9A18 | What term describes station output, taking into account all gains and losses?
A. Power factor
B. Half-power bandwidth
C. Effective radiated power
D. Apparent power

111. E9A18 (C) | What term describes station output, taking into account all gains and losses?
A. Power factor
B. Half-power bandwidth
C. Effective radiated power
D. Apparent power

112. E9B01 | In the antenna radiation pattern shown in Figure E9-1, what is the 3 dB beam-width?
A. 75 degrees
B. 50 degrees
C. 25 degrees
D. 30 degrees

113. E9C – Wire and phased array antennas: rhombic antennas; effects of ground reflections; take-off angles; Practical wire antennas: Zepps, OCFD, loops

114. Wire and Phased Array Antennas
There are many ways to put up antennas that are directional.
Yagis are directional antennas, but they require a structure, such as a tower, to get them high in the air.
One way to get directionality without a tower is to use phased vertical arrays.
In general, the phased vertical array consists of two or more quarter-wave vertical antennas.
The radiation pattern that the array will have depends on how you feed the vertical antennas.

115. Wire and Phased Array Antennas
So, for example, the radiation pattern of two 1/4- wavelength vertical antennas spaced 1/2-wavelength apart and fed 180 degrees out of phase is a figure-8 oriented along the axis of the array. (E9C01)
The radiation pattern of two 1/4-wavelength vertical antennas spaced 1/4-wavelength apart and fed 90 degrees out of phase is a cardioid. (E9C02)
The radiation pattern of two 1/4-wavelength vertical antennas spaced 1/2-wavelength apart and fed in phase is a Figure-8 broadside to the axis of the array. (E9C03)

116. Wire and Phased Array Antennas
How and where you install an antenna affects its radiation pattern.
For example, the far-field elevation pattern of a vertically polarized antenna is affected when it is mounted over seawater versus rocky ground. What happens is that the low-angle radiation increases. (E9C11)
The main effect of placing a vertical antenna over an imperfect ground is that it reduces low-angle radiation. (E9C13)

117. Wire antennas There are many different kinds of wire antennas.
Some of the more popular are;
the long-wire antenna
the folded dipole antenna
the off-center fed dipole antenna
the Zepp antenna
the G5RV antenna.

118. Wire antennas
The long-wire antenna, as the name implies, is just a long piece of wire, as long as you can make it, strung up as high as you can string it.
An antenna tuner is almost always required to match the impedance at the end of the long wire to the 50 Ω output of the transmitter. The radiation pattern of a long-wire antenna is very unpredictable.
What happens to the radiation pattern of an unterminated long wire antenna as the wire length is increased is that the lobes align more in the direction of the wire. (E9C04)

119. Wire antennas
The folded dipole is a variation on the basic half-wave dipole antenna.
A folded dipole antenna is a dipole consisting of one wavelength of wire forming a very thin loop. (E9C08)
The approximate feed point impedance at the center of a two-wire folded dipole antenna is 300 ohms. (E9C07)
This antenna was very popular when 300 Ω twinlead was used for TV antennas. The reason for this is that 300 Ω was widely available and you could use is for both the antenna and the feedline.

120. Wire antennas
Another popular variation on the half-wave dipole is the off-center fed dipole, or OFCD.
An OCFD antenna is a dipole feed approximately 1/3 the way from one end with a 4:1 balun to provide multiband operation. (E9C05)
The reason this antenna has become so popular is that not only provides a good match on its fundamental frequency, but on harmonically-related frequencies as well.
An OFCD antenna cut for the 80 m band, for example, will also present a good match on 40m, 15m, and 10m bands.

121. Wire antennas Zepp antennas are also half-wavelength antennas.
A Zepp antenna is an end fed dipole antenna. (E9C10)
Because the impedance is very high at the feedpoint, the Zepp antenna uses a quarter- wave length of transmission line to transform the impedance to something closer to the 50 Ω transmitter output impedance.

122. Wire antennas
An example of a wire antenna that is not a half- wavelenght long is the G5RV antenna.
A G5RV antenna is a multi-band dipole antenna fed with coax and a balun through a selected length of open wire transmission line. (E9C09)
The G5RV was originally designed as a single- band, 20m antenna that provided some directionality.
Amateurs soon found that they could easily tune this antenna on other frequency bands, and this multi-band capability has made it very popular.

123. Wire antennas
Rhombic antennas are large wire antennas that have four sections, each one or more wavelengths long, arranged in a rhombic shape, and fed at one end of the rhomboid.
When the end opposite the feed point is open, the antenna is bidirectional.
Putting a terminating resistor on a rhombic antenna, however, changes the radiation pattern from bidirectional to unidirectional. (E9C06)

124. E9C01 | What is the radiation pattern of two 1/4-wavelength vertical antennas spaced 1/2-wavelength apart and fed 180 degrees out of phase?
A. Cardioid
B. Omni-directional
C. A figure-8 broadside to the axis of the array
D. A figure-8 oriented along the axis of the array

125. E9C01 (D) | What is the radiation pattern of two 1/4-
wavelength vertical antennas spaced 1/2-wavelength apart and fed 180 degrees out of phase?
A. Cardioid
B. Omni-directional
C. A figure-8 broadside to the axis of the array
D. A figure-8 oriented along the axis of the array

126. E9C02 | What is the radiation pattern of two 1/4 wavelength vertical antennas spaced 1/4 wavelength apart and fed 90 degrees out of phase?
A. Cardioid
B. A figure-8 end-fire along the axis of the array
C. A figure-8 broadside to the axis of the array
D. Omni-directional

127. E9C02 (A) | What is the radiation pattern of two 1/4
wavelength vertical antennas spaced 1/4 wavelength apart and fed 90 degrees out of phase?
A. Cardioid
B. A figure-8 end-fire along the axis of the array
C. A figure-8 broadside to the axis of the array
D. Omni-directional

128. E9C03 | What is the radiation pattern of two 1/4 wavelength vertical antennas spaced a 1/2 wavelength apart and fed in phase?
A. Omni-directional
B. Cardioid
C. A Figure-8 broadside to the axis of the array
D. A Figure-8 end-fire along the axis of the array

129. E9C03 (C) | What is the radiation pattern of two 1/4
wavelength vertical antennas spaced a 1/2 wavelength apart and fed in phase?
A. Omni-directional
B. Cardioid
C. A Figure-8 broadside to the axis of the array
D. A Figure-8 end-fire along the axis of the array

130. E9C04 | What happens to the radiation pattern of an unterminated long wire antenna as the wire length is increased?
A. The lobes become more perpendicular to the wire
B. The lobes align more in the direction of the wire
C. The vertical angle increases
D. The front-to-back ratio decreases

131. E9C04 (B) | What happens to the radiation pattern of an unterminated long wire antenna as the wire length is increased?
A. The lobes become more perpendicular to the wire
B. The lobes align more in the direction of the wire
C. The vertical angle increases
D. The front-to-back ratio decreases

132. E9C05 | What is an OCFD antenna?
A. A dipole feed approximately 1/3 the way from one end with a 4:1 balun to provide multiband operation
B. A remotely tunable dipole antenna using orthogonally controlled frequency diversity
C. An eight band dipole antenna using octophase filters
D. A multiband dipole antenna using one-way circular polarization for frequency diversity

133. E9C05 (A) | What is an OCFD antenna?
A. A dipole feed approximately 1/3 the way from one end with a 4:1 balun to provide multiband operation
B. A remotely tunable dipole antenna using orthogonally controlled frequency diversity
C. An eight band dipole antenna using octophase filters
D. A multiband dipole antenna using one-way circular polarization for frequency diversity

134. E9C06 | What is the effect of a terminating resistor on a rhombic antenna?
A. It reflects the standing waves on the antenna elements back to the transmitter
B. It changes the radiation pattern from bidirectional to unidirectional
C. It changes the radiation pattern from horizontal to vertical polarization
D. It decreases the ground loss

135. E9C06 (B) | What is the effect of a terminating resistor on a rhombic antenna?
A. It reflects the standing waves on the antenna elements back to the transmitter
B. It changes the radiation pattern from bidirectional to unidirectional
C. It changes the radiation pattern from horizontal to vertical polarization
D. It decreases the ground loss

136. E9C07 | What is the approximate feed point impedance at the center of a two-wire folded dipole antenna?
A. 300 ohms
B. 72 ohms
C. 50 ohms
D. 450 ohms

137. E9C07 (A) | What is the approximate feed point impedance at the center of a two-wire folded dipole antenna?
A. 300 ohms
B. 72 ohms
C. 50 ohms
D. 450 ohms

138. E9C08 | What is a folded dipole antenna?
A. A dipole one-quarter wavelength long
B. A type of ground-plane antenna
C. A dipole consisting of one wavelength of wire forming a very thin loop
D. A dipole configured to provide forward gain

139. E9C08 (C) | What is a folded dipole antenna?
A. A dipole one-quarter wavelength long
B. A type of ground-plane antenna
C. A dipole consisting of one wavelength of wire forming a very thin loop
D. A dipole configured to provide forward gain

140. E9C09 | What is a G5RV antenna?
A. A multi-band dipole antenna fed with coax and a balun through a selected length of open wire transmission line
B. A multi-band trap antenna
C. A phased array antenna consisting of multiple loops
D. A wide band dipole using shorted coaxial cable for the radiating elements and fed with a 4:1 balun

141. E9C09 (A) | What is a G5RV antenna?
A. A multi-band dipole antenna fed with coax and a balun through a selected length of open wire transmission line
B. A multi-band trap antenna
C. A phased array antenna consisting of multiple loops
D. A wide band dipole using shorted coaxial cable for the radiating elements and fed with a 4:1 balun

142. E9C10 | Which of the following describes a Zepp antenna?
A. A dipole constructed from zip cord
B. An end fed dipole antenna
C. An omni-directional antenna commonly used for satellite communications
D. A vertical array capable of quickly changing the direction of maximum radiation by changing phasing lines

143. E9C10 (B) | Which of the following describes a Zepp antenna?
A. A dipole constructed from zip cord
B. An end fed dipole antenna
C. An omni-directional antenna commonly used for satellite communications
D. A vertical array capable of quickly changing the direction of maximum radiation by changing phasing lines

144. E9C11 | How is the far-field elevation pattern of a vertically polarized antenna affected by being mounted over seawater versus rocky ground?
A. The low-angle radiation decreases
B. The high-angle radiation increases
C. Both the high-angle and low-angle radiation decrease
D. The low-angle radiation increases

145. E9C11 (D) | How is the far-field elevation pattern of a vertically polarized antenna affected by being mounted over seawater versus rocky ground?
A. The low-angle radiation decreases
B. The high-angle radiation increases
C. Both the high-angle and low-angle radiation decrease
D. The low-angle radiation increases

146. E9C12 | Which of the following describes an extended double Zepp antenna?
A. A wideband vertical antenna constructed from precisely tapered aluminum tubing
B. A portable antenna erected using two push support poles
C. A center fed 1.25 wavelength antenna (two 5/8 wave elements in phase)
D. An end fed folded dipole antenna

147. E9C12 (C) | Which of the following describes an extended double Zepp antenna?
A. A wideband vertical antenna constructed from precisely tapered aluminum tubing
B. A portable antenna erected using two push support poles
C. A center fed 1.25 wavelength antenna (two 5/8 wave elements in phase)
D. An end fed folded dipole antenna

148. E9C13 | What is the main effect of placing a vertical antenna over an imperfect ground?
A. It causes increased SWR
B. It changes the impedance angle of the matching network
C. It reduces low-angle radiation
D. It reduces losses in the radiating portion of the antenna

149. E9C13 (C) | What is the main effect of placing a vertical antenna over an imperfect ground?
A. It causes increased SWR
B. It changes the impedance angle of the matching network
C. It reduces low-angle radiation
D. It reduces losses in the radiating portion of the antenna

150. E9C14 | How does the performance of a horizontally polarized antenna mounted on the side of a hill compare with the same antenna mounted on flat ground?
A. The main lobe takeoff angle increases in the downhill direction
B. The main lobe takeoff angle decreases in the downhill direction
C. The horizontal beam width decreases in the downhill direction
D. The horizontal beam width increases in the uphill direction

151. E9C14 (B) | How does the performance of a horizontally
polarized antenna mounted on the side of a hill compare with the same antenna mounted on flat ground?
A. The main lobe takeoff angle increases in the downhill direction
B. The main lobe takeoff angle decreases in the downhill direction
C. The horizontal beam width decreases in the downhill direction
D. The horizontal beam width increases in the uphill direction

152. E9C15 | How does the radiation pattern of a horizontally
polarized 3-element beam antenna vary with its height above ground?
A. The main lobe takeoff angle increases with increasing height
B. The main lobe takeoff angle decreases with increasing height
C. The horizontal beam width increases with height
D. The horizontal beam width decreases with height

153. E9C15 (B) | How does the radiation pattern of a horizontally polarized 3-element beam antenna vary with its height above ground?
A. The main lobe takeoff angle increases with increasing height
B. The main lobe takeoff angle decreases with increasing height
C. The horizontal beam width increases with height
D. The horizontal beam width decreases with height

154. E9D01 | How does the gain of an ideal parabolic dish antenna change when the operating frequency is doubled?
A. Gain does not change
B. Gain is multiplied by 0.707
C. Gain increases by 6 dB
D. Gain increases by 3 dB

155. E9D
E9D – Directional antennas: gain; Yagi antennas; losses; SWR bandwidth; antenna efficiency; shortened and mobile antennas; RF grounding

156. Directional antennas
This section consists of a miscellaneous selection of antenna questions.
We’ll start with some questions about directional antennas, then talk a little bit about vertical antennas, then mobile antennas, and finally grounding.

157. Directional antennas
When designing a Yagi antenna, you might think that the most important parameter is forward gain.
What usually occurs if a Yagi antenna is designed solely for maximum forward gain, though, is that the front-to-back ratio decreases. (E9D13)
In other words, the antenna becomes more bi- directional than simply directional.

158. Directional antennas
On the VHF and UHF bands, Yagi antennas are operated either horizontally for weak-signal work and vertically for FM operations.
In some cases, however circular polarization is desirable. You can use linearly polarized Yagi antennas to produce circular polarization if you arrange two Yagis perpendicular to each other with the driven elements at the same point on the boom and feed them 90 degrees out of phase. (E9D02)
The disadvantage to this approach is, obviously, that you need two antennas, instead of just one to achieve circular polarization.

159. Parabolic antennas
Parabolic antennas are often used at microwave frequencies to direct a signal in a particular direction.
One thing to keep in mind is that gain increases by 6 dB if you are using an ideal parabolic dish antenna when the operating frequency is doubled. (E9D01)
Also keep in mind that, as pointed out earlier, the beam width is narrower as well.

160. Mobile HF Antenna
Designing an efficient mobile HF antenna is perhaps the toughest job for a radio amateur. Mobile antennas, almost by definition, must be shorter than a quarter wave and present a capacitive load.
What happens to the feed point impedance at the base of a fixed length HF mobile antenna as the frequency of operation is lowered is that the radiation resistance decreases and the capacitive reactance increases. (E9D10)

161. Mobile HF Antenna
The function of a loading coil as used with an HF mobile antenna is, therefore, to cancel capacitive reactance. (E9D09)
In effect, loading coils to make the radiator of a short vertical antenna look electrically longer.

162. Mobile HF Antenna
Because short verticals have a low radiation resistance, they are inherently inefficient, and you need to do whatever you can to make them as efficient as possible.
An HF mobile antenna loading coil should have a high ratio of reactance to resistance to minimize losses. (E9D04)
A high-Q loading coil (one with a high ratio of reactance to resistance) should be placed near the center of the vertical radiator to minimize losses in a shortened vertical antenna. (E9D03)

163. Mobile HF Antenna
Unfortunately, what happens to the bandwidth of an antenna as it is shortened through the use of loading coils is that it is decreased. (E9D06)
In other words, what happens as the Q of an antenna increases is that the SWR bandwidth decreases. (E9D08)
One way to improve the efficiency of a short vertical is to use a technique called top loading.
An advantage of using top loading in a shortened HF vertical antenna is improved radiation efficiency. (E9D07)
This is most often accomplished by using a “capacitance hat” on the top of the vertical element.

164. Multi-band Often, antennas use traps to yield multi-band operation.
A disadvantage of using a multiband trapped antenna is that it might radiate harmonics. (E9D05)
For example, if your 40m transmissions have high harmonic content on 20m, and the multiband vertical is also resonant on 20m, it will radiate those harmonics.

165. RF grounding Much has been written about station grounding.
One thing’s for sure.
A station’s safety ground is not adequate as an RF ground. The reason for this is that conductors present different impedances at different frequencies.

166. RF grounding
A wide flat copper strap is the type of conductor that would be best for minimizing losses in a station’s RF ground system. (E9D11)
The main reason for this is that RF tends to be conducted near the surface of a conductor.
The more surface area there is, the lower the impedance to ground.

167. RF grounding
To minimize inductance, it’s best to keep the RF ground connection as short as possible. 
An electrically-short connection to 3 or 4 interconnected ground rods driven into the Earth would provide the best RF ground for your station. (E9D12)

168. First Antenna
For many amateurs, their first antenna is a trapped vertical antenna.
One advantage of using a trapped antenna is that it may be used for multi band operation. (E9D12)
Another big advantage is that it doesn’t require a lot of space when compared to a dipole antenna.

169. E9D01 | How does the gain of an ideal parabolic dish antenna change when the operating frequency is doubled?
A. Gain does not change
B. Gain is multiplied by 0.707
C. Gain increases by 6 dB
D. Gain increases by 3 dB

170. E9D01 (C) | How does the gain of an ideal parabolic dish antenna change when the operating frequency is doubled?
A. Gain does not change
B. Gain is multiplied by 0.707
C. Gain increases by 6 dB
D. Gain increases by 3 dB

171. E9D02 | How can linearly polarized Yagi antennas be used to produce circular polarization?
A. Stack two Yagis fed 90 degrees out of phase to form an array with the respective elements in parallel planes
B. Stack two Yagis fed in phase to form an array with the respective elements in parallel planes
C. Arrange two Yagis perpendicular to each other with the driven
elements at the same point on the boom fed 90 degrees out of phase
D. Arrange two Yagis collinear to each other with the driven elements fed 180 degrees out of phase

172. E9D02 (C) | How can linearly polarized Yagi antennas be used to produce circular polarization?
A. Stack two Yagis fed 90 degrees out of phase to form an array with the respective elements in parallel planes
B. Stack two Yagis fed in phase to form an array with the respective elements in parallel planes
C. Arrange two Yagis perpendicular to each other with the
driven elements at the same point on the boom fed 90 degrees out of phase
D. Arrange two Yagis collinear to each other with the driven elements fed 180 degrees out of phase

173. E9D03 | Where should a high Q loading coil be placed to minimize losses in a shortened vertical antenna?
A. Near the center of the vertical radiator
B. As low as possible on the vertical radiator
C. As close to the transmitter as possible
D. At a voltage node

174. E9D03 (A) | Where should a high Q loading coil be placed to minimize losses in a shortened vertical antenna?
A. Near the center of the vertical radiator
B. As low as possible on the vertical radiator
C. As close to the transmitter as possible
D. At a voltage node

175. E9D04 | Why should an HF mobile antenna loading coil have a high ratio of reactance to resistance?
A. To swamp out harmonics
B. To maximize losses
C. To minimize losses
D. To minimize the Q

176. E9D04 (C) | Why should an HF mobile antenna loading coil have a high ratio of reactance to resistance?
A. To swamp out harmonics
B. To maximize losses
C. To minimize losses
D. To minimize the Q

177. E9D05 | What is a disadvantage of using a multiband trapped antenna?
A. It might radiate harmonics
B. It radiates the harmonics and fundamental equally well
C. It is too sharply directional at lower frequencies
D. It must be neutralized

178. E9D05 (A) | What is a disadvantage of using a multiband trapped antenna?
A. It might radiate harmonics
B. It radiates the harmonics and fundamental equally well
C. It is too sharply directional at lower frequencies
D. It must be neutralized

179. E9D06 | What happens to the bandwidth of an antenna as it is shortened through the use of loading coils?
A. It is increased
B. It is decreased
C. No change occurs
D. It becomes flat

180. E9D06 (B) | What happens to the bandwidth of an antenna as it is shortened through the use of loading coils?
A. It is increased
B. It is decreased
C. No change occurs
D. It becomes flat

181. E9D07 | What is an advantage of using top loading in a shortened HF vertical antenna?
A. Lower Q
B. Greater structural strength
C. Higher losses
D. Improved radiation efficiency

182. E9D07 (D) | What is an advantage of using top loading in a shortened HF vertical antenna?
A. Lower Q
B. Greater structural strength
C. Higher losses
D. Improved radiation efficiency

183. E9D08 | What happens as the Q of an antenna increases?
A. SWR bandwidth increases
B. SWR bandwidth decreases
C. Gain is reduced
D. More common-mode current is present on the feed line

184. E9D08 (B) | What happens as the Q of an antenna increases?
A. SWR bandwidth increases
B. SWR bandwidth decreases
C. Gain is reduced
D. More common-mode current is present on the feed line

185. E9D09 | What is the function of a loading coil used as part of an HF mobile antenna?
A. To increase the SWR bandwidth
B. To lower the losses
C. To lower the Q
D. To cancel capacitive reactance

186. E9D09 (D) | What is the function of a loading coil used as part of an HF mobile antenna?
A. To increase the SWR bandwidth
B. To lower the losses
C. To lower the Q
D. To cancel capacitive reactance

187. E9D10 | What happens to feed point impedance at the base of a fixed length HF mobile antenna as the frequency of operation is lowered?
A. The radiation resistance decreases and the capacitive reactance decreases
B. The radiation resistance decreases and the capacitive reactance increases
C. The radiation resistance increases and the capacitive reactance decreases
D. The radiation resistance increases and the capacitive reactance increases

188. E9D10 (B) | What happens to feed point impedance at the base of a fixed length HF mobile antenna as the frequency of operation is lowered?
A. The radiation resistance decreases and the capacitive reactance decreases
B. The radiation resistance decreases and the capacitive reactance increases
C. The radiation resistance increases and the capacitive reactance decreases
D. The radiation resistance increases and the capacitive reactance increases

189. E9D11 | Which of the following types of conductors would be best for minimizing losses in a station's RF ground system?
A. A resistive wire, such as spark plug wire
B. A wide flat copper strap
C. A cable with six or seven 18 gauge conductors in parallel
D. A single 12 gauge or 10 gauge stainless steel wire

190. E9D11 (B) | Which of the following types of conductors would be best for minimizing losses in a station's RF ground system?
A. A resistive wire, such as spark plug wire
B. A wide flat copper strap
C. A cable with six or seven 18 gauge conductors in parallel
D. A single 12 gauge or 10 gauge stainless steel wire

191. E9D12 | Which of the following would provide the best RF ground for your station?
A. A 50 ohm resistor connected to ground
B. An electrically short connection to a metal water pipe
C. An electrically short connection to 3 or 4 interconnected ground rods driven into the Earth
D. An electrically short connection to 3 or 4 interconnected ground rods via a series RF choke

192. E9D12 (C) | Which of the following would provide the best RF ground for your station?
A. A 50 ohm resistor connected to ground
B. An electrically short connection to a metal water pipe
C. An electrically short connection to 3 or 4 interconnected ground rods driven into the Earth
D. An electrically short connection to 3 or 4 interconnected ground rods via a series RF choke

193. E9D13 | What usually occurs if a Yagi antenna is designed solely for maximum forward gain?
A. The front-to-back ratio increases
B. The front-to-back ratio decreases
C. The frequency response is widened over the whole frequency band
D. The SWR is reduced

194. E9D13 (B) | What usually occurs if a Yagi antenna is designed solely for maximum forward gain?
A. The front-to-back ratio increases
B. The front-to-back ratio decreases
C. The frequency response is widened over the whole frequency band
D. The SWR is reduced

195. E9E01 | What system matches a higher impedance transmission line to a lower impedance antenna by connecting the line to the driven element in two places spaced a fraction of a wavelength each side of element center?
A. The gamma matching system
B. The delta matching system
C. The omega matching system
D. The stub matching system

196. E9E – Matching: matching antennas to feed lines; power dividers

197. Matching
For many types of antennas, matching the impedance of the antenna to the impedance of the feedline, normally coax, is essential.
Mismatched lines create high SWR and, consequently, feedline losses. 
An SWR greater than 1:1 is characteristic of a mismatched transmission line. (E9E08)

198. Matching
When a feedline and antenna are mismatched, some of the power you are trying to transmit will be reflected back down the feedline.
The ratio of the amplitude of the reflected wave to the amplitude of the wave you are trying to send is called the reflection ratio, and it is mathematically related to SWR. 
Reflection coefficient is the term that best describes the interactions at the load end of a mismatched transmission line. (E9E07)

199. Matching
To match the impedance of the feedline to the impedance of the antenna, we use a variety of different techniques. 
The delta matching system matches a high- impedance transmission line to a lower impedance antenna by connecting the line to the driven element in two places spaced a fraction of a wavelength each side of element center. (E9E01)

200. Matching
The gamma match is the name of an antenna matching system that matches an unbalanced feed line to an antenna by feeding the driven element both at the center of the element and at a fraction of a wavelength to one side of center. (E9E02)
The purpose of the series capacitor in a gamma- type antenna matching network is to cancel the inductive reactance of the matching network. (E9E04)
The gamma match is an effective method of connecting a 50-ohm coaxial cable feed line to a grounded tower so it can be used as a vertical antenna. (E9E09)

201. Matching
The stub match is the name of the matching system that uses a section of transmission line connected in parallel with the feed line at or near the feed point. (E9E03)
What the stub does is to add reactance at the feed point.
By varying the length of the stub, you can change the reactance that the stub provides to whatever value is needed.
An effective way of matching a feed line to a VHF or UHF antenna when the impedances of both the antenna and feed line are unknown is to use the universal stub matching technique. (E9E11)

202. Matching
Inserting a 1/4-wavelength piece of 75-ohm coaxial cable transmission line in series between the antenna terminals and the 50- ohm feed cable is an effective way to match an antenna with a 100-ohm feed point impedance to a 50-ohm coaxial cable feed line. (E9E10)
Note that this only works on one band as the length of 75-ohm coax you use will only be 1/4 of a wavelength on one band.

203. Matching
Many directly-fed Yagi antennas have feed point impedances of approximately 20 to 25 ohms.
One technique often use to match these antennas to 50-ohm coaxial cable is the hairpin match.
To use a hairpin matching system to tune the driven element of a 3-element Yagi, the driven element reactance must be capacitive. (E9E05)
The equivalent lumped-constant network for a hairpin matching system on a 3-element Yagi is a shunt inductor. (E9E06)

204. Matching
Some beam antennas use multiple driven elements in order to make them multi-band antennas.
The primary purpose of a phasing line when used with an antenna having multiple driven elements is that it ensures that each driven element operates in concert with the others to create the desired antenna pattern. (E9E12)

205. Matching
I’m not sure that Wilkinson dividers are used much in antenna systems, or why this question is in the section on feedline matching, but here it is.
One use of a Wilkinson divider is,  It is used to divide power equally between two 50 ohm loads while maintaining 50 ohm input impedance. (E9E13)

206. E9E01 | What system matches a higher impedance transmission line to a lower impedance antenna by connecting the line to the driven element in two places spaced a fraction of a wavelength each side of element center?
A. The gamma matching system
B. The delta matching system
C. The omega matching system
D. The stub matching system

207. E9E01 (B) | What system matches a higher impedance
transmission line to a lower impedance antenna by connecting the line to the driven element in two places spaced a fraction of a wavelength each side of element center?
A. The gamma matching system
B. The delta matching system
C. The omega matching system
D. The stub matching system

208. E9E02 | What is the name of an antenna matching system that matches an unbalanced feed line to an antenna by feeding the driven element both at the center of the element and at a fraction of a wavelength to one side of center?
A. The gamma match
B. The delta match
C. The epsilon match
D. The stub match

209. E9E02 (A) | What is the name of an antenna matching system that matches an unbalanced feed line to an antenna by feeding the driven element both at the center of the element and at a fraction of a wavelength to one side of center?
A. The gamma match
B. The delta match
C. The epsilon match
D. The stub match

210. E9E03 | What is the name of the matching system that uses a section of transmission line connected in parallel with the feed line at or near the feed point?
A. The gamma match
B. The delta match
C. The omega match
D. The stub match

211. E9E03 (D) | What is the name of the matching system that uses a section of transmission line connected in parallel with the feed line at or near the feed point?
A. The gamma match
B. The delta match
C. The omega match
D. The stub match

212. E9E04 | What is the purpose of the series capacitor in a gamma-type antenna matching network?
A. To provide DC isolation between the feed line and the antenna
B. To cancel the inductive reactance of the matching network
C. To provide a rejection notch that prevents the radiation of harmonics
D. To transform the antenna impedance to a higher value

213. E9E04 (B) | What is the purpose of the series capacitor in a gamma-type antenna matching network?
A. To provide DC isolation between the feed line and the antenna
B. To cancel the inductive reactance of the matching network
C. To provide a rejection notch that prevents the radiation of harmonics
D. To transform the antenna impedance to a higher value

214. E9E05 | How must the driven element in a 3-element Yagi be tuned to use a hairpin matching system?
A. The driven element reactance must be capacitive
B. The driven element reactance must be inductive
C. The driven element resonance must be lower than the operating frequency
D. The driven element radiation resistance must be higher than the characteristic impedance of the transmission line

215. E9E05 (A) | How must the driven element in a 3-element Yagi be tuned to use a hairpin matching system?
A. The driven element reactance must be capacitive
B. The driven element reactance must be inductive
C. The driven element resonance must be lower than the operating frequency
D. The driven element radiation resistance must be higher than the characteristic impedance of the transmission line

216. E9E06 | What is the equivalent lumped-constant network for a hairpin matching system of a 3-element Yagi?
A. Pi-network
B. Pi-L-network
C. A shunt inductor
D. A series capacitor

217. E9E06 (C) | What is the equivalent lumped-constant network for a hairpin matching system of a 3-element Yagi?
A. Pi-network
B. Pi-L-network
C. A shunt inductor
D. A series capacitor

218. E9E07 | What term best describes the interactions at the load end of a mismatched transmission line?
A. Characteristic impedance
B. Reflection coefficient
C. Velocity factor
D. Dielectric constant

219. E9E07 (B) | What term best describes the interactions at the load end of a mismatched transmission line?
A. Characteristic impedance
B. Reflection coefficient
C. Velocity factor
D. Dielectric constant

220. E9E08 | Which of the following measurements is characteristic of a mismatched transmission line?
A. An SWR less than 1:1
B. A reflection coefficient greater than 1
C. A dielectric constant greater than 1
D. An SWR greater than 1:1

221. E9E08 (D) | Which of the following measurements is characteristic of a mismatched transmission line?
A. An SWR less than 1:1
B. A reflection coefficient greater than 1
C. A dielectric constant greater than 1
D. An SWR greater than 1:1

222. E9E09 | Which of these matching systems is an effective
method of connecting a 50 ohm coaxial cable feed line to a grounded tower so it can be used as a vertical antenna?
A. Double-bazooka match
B. Hairpin match
C. Gamma match
D. All of these choices are correct

223. E9E09 (C) | Which of these matching systems is an effective method of connecting a 50 ohm coaxial cable feed line to a grounded tower so it can be used as a vertical antenna?
A. Double-bazooka match
B. Hairpin match
C. Gamma match
D. All of these choices are correct

224. E9E10 | Which of these choices is an effective way to match an antenna with a 100 ohm feed point impedance to a 50 ohm coaxial cable feed line?
A. Connect a 1/4-wavelength open stub of 300 ohm twin-lead in parallel with the coaxial feed line where it connects to the antenna
B. Insert a 1/2 wavelength piece of 300 ohm twin-lead in series between the antenna terminals and the 50 ohm feed cable
C. Insert a 1/4-wavelength piece of 75 ohm coaxial cable transmission line in series between the antenna terminals and the 50 ohm feed cable
D. Connect 1/2 wavelength shorted stub of 75 ohm cable in parallel with the 50 ohm cable where it attaches to the antenna

225. E9E10 (C) | Which of these choices is an effective way to match an antenna with a 100 ohm feed point impedance to a 50 ohm coaxial cable feed line?
A. Connect a 1/4-wavelength open stub of 300 ohm twin-lead in parallel with the coaxial feed line where it connects to the antenna
B. Insert a 1/2 wavelength piece of 300 ohm twin-lead in series between the antenna terminals and the 50 ohm feed cable
C. Insert a 1/4-wavelength piece of 75 ohm coaxial cable
transmission line in series between the antenna terminals and the 50 ohm feed cable
D. Connect 1/2 wavelength shorted stub of 75 ohm cable in parallel with the 50 ohm cable where it attaches to the antenna

226. E9E11 | What is an effective way of matching a feed line to a VHF or UHF antenna when the impedances of both the antenna and feed line are unknown?
A. Use a 50 ohm 1:1 balun between the antenna and feed line
B. Use the universal stub matching technique
C. Connect a series-resonant LC network across the antenna feed terminals
D. Connect a parallel-resonant LC network across the antenna feed terminals

227. E9E11 (B) | What is an effective way of matching a feed line to a VHF or UHF antenna when the impedances of both the antenna and feed line are unknown?
A. Use a 50 ohm 1:1 balun between the antenna and feed line
B. Use the universal stub matching technique
C. Connect a series-resonant LC network across the antenna feed terminals
D. Connect a parallel-resonant LC network across the antenna feed terminals

228. E9E12 | What is the primary purpose of a phasing line when used with an antenna having multiple driven elements?
A. It ensures that each driven element operates in concert with the others to create the desired antenna pattern
B. It prevents reflected power from traveling back down the feed line and causing harmonic radiation from the transmitter
C. It allows single-band antennas to operate on other bands
D. It makes sure the antenna has a low-angle radiation pattern

229. E9E12 (A) | What is the primary purpose of a phasing line when used with an antenna having multiple driven elements?
A. It ensures that each driven element operates in concert with the others to create the desired antenna pattern
B. It prevents reflected power from traveling back down the feed line and causing harmonic radiation from the transmitter
C. It allows single-band antennas to operate on other bands
D. It makes sure the antenna has a low-angle radiation pattern

230. E9E13 | What is a use for a Wilkinson divider?
A. It divides the operating frequency of a transmitter signal so it can be used on a lower frequency band
B. It is used to feed high-impedance antennas from a low-impedance source
C. It is used to divide power equally between two 50 ohm loads while maintaining 50 ohm input impedance
D. It is used to feed low-impedance loads from a high-impedance source

231. E9E13 (C) | What is a use for a Wilkinson divider?
A. It divides the operating frequency of a transmitter signal so it can be used on a lower frequency band
B. It is used to feed high-impedance antennas from a low-impedance source
C. It is used to divide power equally between two 50 ohm loads while maintaining 50 ohm input impedance
D. It is used to feed low-impedance loads from a high-impedance source

232. E9F
E9F – Transmission lines: characteristics of open and shorted feed lines; 1/8 wavelength; 1/4 wavelength; 1/2 wavelength; feed lines: coax versus open- wire; velocity factor; electrical length; coaxial cable dielectrics; velocity factor

233. Transmission lines
The physical length of a coaxial cable transmission line is shorter than its electrical length because electrical signals move more slowly in a coaxial cable than in air. (E9F03)
The term we use to quantify the difference in how fast a wave travels in air versus how fast it travels in a feedline is velocity factor.

234. Transmission lines
The velocity factor of a transmission line is the velocity of the wave in the transmission line divided by the velocity of light in a vacuum. (E9F01)
Put another way, velocity factor is the term for the ratio of the actual speed at which a signal travels through a transmission line to the speed of light in a vacuum. (E9F08) 
The dielectric materials used in the line determines the velocity factor of a transmission line. (E9F02)

235. Transmission lines
The typical velocity factor for a coaxial cable with solid polyethylene dielectric is (E9F04)
That makes the approximate physical length of a solid polyethylene dielectric coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz about 3.5 meters. (E9F05)
The approximate physical length of a solid polyethylene dielectric coaxial transmission line that is electrically one-quarter wavelength long at 7.2 MHz is 6.9 meters. (E9F09)

236. Transmission lines
The velocity factor of air-insulated, parallel conductor transmission lines is a lot closer to 1 than the velocity factor for coaxial cable.
The approximate physical length of an air- insulated, parallel conductor transmission line that is electrically one-half wavelength long at MHz is 10 meters. (E9F06)

237. Transmission lines
While having a higher velocity factor is not really such a big advantage, open-wire or ladder line feedlines do have other advantages.
For example, ladder line has lower loss than small-diameter coaxial cable such as RG-58 at 50 MHz. (E9F07)

238. Transmission lines
Sometimes we use various lengths of coax to match an antenna system or to filter out frequencies.
A 1/8-wavelength transmission line presents an inductive reactance to a generator when the line is shorted at the far end. (E9F10)
A 1/8-wavelength transmission line presents a capacitive reactance to a generator when the line is open at the far end. (E9F11)

239. Transmission lines
A 1/4-wavelength transmission line presents a very low impedance to a generator when the line is open at the far end. (E9F12)
A 1/4-wavelength transmission line presents a very high impedance to a generator when the line is shorted at the far end. (E9F13)
A 1/2-wavelength transmission line presents a very low impedance to a generator when the line is shorted at the far end. (E9F14) A 1/2-wavelength transmission line presents a very high impedance to a generator when the line is open at the far end. (E9F15)

240. Transmission lines
All of these choices are correct when talking about significant differences between foam- dielectric coaxial cable and solid-dielectric cable, assuming all other parameters are the same (E9F16):
Foam dielectric has lower safe operating voltage limits
Foam dielectric has lower loss per unit of length
Foam dielectric has higher velocity factor

241. E9F01 | What is the velocity factor of a transmission line?
A. The ratio of the characteristic impedance of the line to the terminating impedance
B. The index of shielding for coaxial cable
C. The velocity of the wave in the transmission line multiplied by the velocity of light in a vacuum
D. The velocity of the wave in the transmission line divided by the velocity of light in a vacuum

242. E9F01 (D) | What is the velocity factor of a transmission line?
A. The ratio of the characteristic impedance of the line to the terminating impedance
B. The index of shielding for coaxial cable
C. The velocity of the wave in the transmission line multiplied by the velocity of light in a vacuum
D. The velocity of the wave in the transmission line divided by the velocity of light in a vacuum

243. E9F02 | Which of the following determines the velocity factor of a transmission line?
A. The termination impedance
B. The line length
C. Dielectric materials used in the line
D. The center conductor resistivity

244. E9F02 (C) | Which of the following determines the velocity factor of a transmission line?
A. The termination impedance
B. The line length
C. Dielectric materials used in the line
D. The center conductor resistivity

245. E9F03 | Why is the physical length of a coaxial cable transmission line shorter than its electrical length?
A. Skin effect is less pronounced in the coaxial cable
B. The characteristic impedance is higher in a parallel feed line
C. The surge impedance is higher in a parallel feed line
D. Electrical signals move more slowly in a coaxial cable than in air

246. E9F03 (D) | Why is the physical length of a coaxial cable transmission line shorter than its electrical length?
A. Skin effect is less pronounced in the coaxial cable
B. The characteristic impedance is higher in a parallel feed line
C. The surge impedance is higher in a parallel feed line
D. Electrical signals move more slowly in a coaxial cable than in air

247. E9F04 | What is the typical velocity factor for a coaxial cable with solid polyethylene dielectric?

248. E9F04 (B) | What is the typical velocity factor for a coaxial cable with solid polyethylene dielectric?
A. 2.70
B. 0.66
C. 0.30
D. 0.10

249. E9F05 | What is the approximate physical length of a solid polyethylene dielectric coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz?
A. 20 meters
B. 2.3 meters
C. 3.5 meters
D. 0.2 meters

250. E9F05 (C) | What is the approximate physical length of a solid polyethylene dielectric coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz?
A. 20 meters
B. 2.3 meters
C. 3.5 meters
D. 0.2 meters

251. E9F06 | What is the approximate physical length of an air- insulated, parallel conductor transmission line that is electrically one-half wavelength long at MHz?
A. 15 meters
B. 20 meters
C. 10 meters
D. 71 meters

252. E9F06 (C) | What is the approximate physical length of an air- insulated, parallel conductor transmission line that is electrically one-half wavelength long at MHz?
A. 15 meters
B. 20 meters
C. 10 meters
D. 71 meters

253. E9F07 | How does ladder line compare to small-diameter coaxial cable such as RG-58 at 50 MHz?
A. Lower loss
B. Higher SWR
C. Smaller reflection coefficient
D. Lower velocity factor

254. E9F07 (A) | How does ladder line compare to small-diameter coaxial cable such as RG-58 at 50 MHz?
A. Lower loss
B. Higher SWR
C. Smaller reflection coefficient
D. Lower velocity factor

255. E9F08 | What is the term for the ratio of the actual speed at
which a signal travels through a transmission line to the speed of light in a vacuum?
A. Velocity factor
B. Characteristic impedance
C. Surge impedance
D. Standing wave ratio

256. E9F08 (A) | What is the term for the ratio of the actual speed at which a signal travels through a transmission line to the speed of light in a vacuum?
A. Velocity factor
B. Characteristic impedance
C. Surge impedance
D. Standing wave ratio

257. E9F09 | What is the approximate physical length of a solid polyethylene dielectric coaxial transmission line that is electrically one-quarter wavelength long at 7.2 MHz?
A. 10 meters
B. 6.9 meters
C. 24 meters
D. 50 meters

258. E9F09 (B) | What is the approximate physical length of a solid polyethylene dielectric coaxial transmission line that is electrically one-quarter wavelength long at 7.2 MHz?
A. 10 meters
B. 6.9 meters
C. 24 meters
D. 50 meters

259. E9F10 | What impedance does a 1/8 wavelength transmission line present to a generator when the line is shorted at the far end?
A. A capacitive reactance
B. The same as the characteristic impedance of the line
C. An inductive reactance
D. The same as the input impedance to the final generator stage

260. E9F10 (C) | What impedance does a 1/8 wavelength
transmission line present to a generator when the line is shorted at the far end?
A. A capacitive reactance
B. The same as the characteristic impedance of the line
C. An inductive reactance
D. The same as the input impedance to the final generator stage

261. E9F11 | What impedance does a 1/8 wavelength transmission line present to a generator when the line is open at the far end?
A. The same as the characteristic impedance of the line
B. An inductive reactance
C. A capacitive reactance
D. The same as the input impedance of the final generator stage

262. E9F11 (C) | What impedance does a 1/8 wavelength
transmission line present to a generator when the line is open at the far end?
A. The same as the characteristic impedance of the line
B. An inductive reactance
C. A capacitive reactance
D. The same as the input impedance of the final generator stage

263. E9F12 | What impedance does a 1/4 wavelength transmission line present to a generator when the line is open at the far end?
A. The same as the characteristic impedance of the line
B. The same as the input impedance to the generator
C. Very high impedance
D. Very low impedance

264. E9F12 (D) | What impedance does a 1/4 wavelength
transmission line present to a generator when the line is open at the far end?
A. The same as the characteristic impedance of the line
B. The same as the input impedance to the generator
C. Very high impedance
D. Very low impedance

265. E9F13 | What impedance does a 1/4 wavelength transmission line present to a generator when the line is shorted at the far end?
A. Very high impedance
B. Very low impedance
C. The same as the characteristic impedance of the transmission line
D. The same as the generator output impedance

266. E9F13 (A) | What impedance does a 1/4 wavelength
transmission line present to a generator when the line is shorted at the far end?
A. Very high impedance
B. Very low impedance
C. The same as the characteristic impedance of the transmission line
D. The same as the generator output impedance

267. E9F14 | What impedance does a 1/2 wavelength transmission line present to a generator when the line is shorted at the far end?
A. Very high impedance
B. Very low impedance
C. The same as the characteristic impedance of the line
D. The same as the output impedance of the generator

268. E9F14 (B) | What impedance does a 1/2 wavelength
transmission line present to a generator when the line is shorted at the far end?
A. Very high impedance
B. Very low impedance
C. The same as the characteristic impedance of the line
D. The same as the output impedance of the generator

269. E9F15 | What impedance does a 1/2 wavelength transmission line present to a generator when the line is open at the far end?
A. Very high impedance
B. Very low impedance
C. The same as the characteristic impedance of the line
D. The same as the output impedance of the generator

270. E9F15 (A) | What impedance does a 1/2 wavelength
transmission line present to a generator when the line is open at the far end?
A. Very high impedance
B. Very low impedance
C. The same as the characteristic impedance of the line
D. The same as the output impedance of the generator

271. E9F16 | Which of the following is a significant difference
between foam dielectric coaxial cable and solid dielectric cable, assuming all other parameters are the same?
A. Foam dielectric has lower safe operating voltage limits
B. Foam dielectric has lower loss per unit of length
C. Foam dielectric has higher velocity factor
D. All of these choices are correct

272. E9F16 (D) | Which of the following is a significant difference
between foam dielectric coaxial cable and solid dielectric cable, assuming all other parameters are the same?
A. Foam dielectric has lower safe operating voltage limits
B. Foam dielectric has lower loss per unit of length
C. Foam dielectric has higher velocity factor
D. All of these choices are correct

273. E9G01 | Which of the following can be calculated using a Smith chart?
A. Impedance along transmission lines
B. Radiation resistance
C. Antenna radiation pattern
D. Radio propagation

274. E9G
E9G – The Smith Chart

275. Smith Chart A Smith chart is shown in Figure E9-3 above. (E9G05)
It is a chart designed to solve transmission line problems graphically.
The resistance axis is the only straight line shown on the Smith chart shown in Figure E9- 3. (E9G07)
Points on this axis are pure resistances. In practice, you want to position the chart so that 0 ohms is at the far left, while infinity is at the far right.

276. Smith Chart
The arcs on a Smith chart represent points with constant reactance. (E9G10)
On the Smith chart, shown in Figure E9-3, the name for the large outer circle on which the reactance arcs terminate is the reactance axis. (E9G06)
Points on the reactance axis have a resistance of 0 ohms.
When oriented so that the resistance axis is horizontal, positive reactances are plotted above the resistance axis and negative reactances below.

277. Smith Chart
The process of normalization with regard to a Smith chart refers to reassigning impedance values with regard to the prime center. (E9G08)
The prime center is the point marked 1.0 on the resistance axis.
If you’re working with a 50 ohm transmission line, you’d normally divide the impedances by 50, meaning that a 50 ohm resistance would then be plotted on the resistance axis at the point marked 1.0.
A reactance of 50 + j100 would be plotted on the resistance circle going through the prime center where it intersects the reactance arc marked 2.0.

278. Smith Chart
Impedance along transmission lines can be calculated using a Smith chart. (E9G01)
Impedance and SWR values in transmission lines are often determined using a Smith chart. (E9G03) 
Standing-wave ratio circles are often added to a Smith chart during the process of solving problems. (E9G09)

279. Smith Chart
The wavelength scales on a Smith chart are calibrated in fractions of transmission line electrical wavelength. (E9G11)
These are useful when trying to determine how long transmission lines must be when used to match a load to a transmitter.

280. E9G01 | Which of the following can be calculated using a Smith chart?
A. Impedance along transmission lines
B. Radiation resistance
C. Antenna radiation pattern
D. Radio propagation

281. E9G01 (A) | Which of the following can be calculated using a Smith chart?
A. Impedance along transmission lines
B. Radiation resistance
C. Antenna radiation pattern
D. Radio propagation

282. E9G02 | What type of coordinate system is used in a Smith chart?
A. Voltage circles and current arcs
B. Resistance circles and reactance arcs
C. Voltage lines and current chords
D. Resistance lines and reactance chords

283. E9G02 (B) | What type of coordinate system is used in a Smith chart?
A. Voltage circles and current arcs
B. Resistance circles and reactance arcs
C. Voltage lines and current chords
D. Resistance lines and reactance chords

284. E9G03 | Which of the following is often determined using a Smith chart?
A. Beam headings and radiation patterns
B. Satellite azimuth and elevation bearings
C. Impedance and SWR values in transmission lines
D. Trigonometric functions

285. E9G03 (C) | Which of the following is often determined using a Smith chart?
A. Beam headings and radiation patterns
B. Satellite azimuth and elevation bearings
C. Impedance and SWR values in transmission lines
D. Trigonometric functions

286. E9G04 | What are the two families of circles and arcs that make up a Smith chart?
A. Resistance and voltage
B. Reactance and voltage
C. Resistance and reactance
D. Voltage and impedance

287. E9G04 (C) | What are the two families of circles and arcs that make up a Smith chart?
A. Resistance and voltage
B. Reactance and voltage
C. Resistance and reactance
D. Voltage and impedance

288. E9G05 | What type of chart is shown in Figure E9-3?
A. Smith chart
B. Free space radiation directivity chart
C. Elevation angle radiation pattern chart
D. Azimuth angle radiation pattern chart

289. E9G05 (A) | What type of chart is shown in Figure E9-3?
A. Smith chart
B. Free space radiation directivity chart
C. Elevation angle radiation pattern chart
D. Azimuth angle radiation pattern chart

290. E9G06 | On the Smith chart shown in Figure E9-3, what is the name for the large outer circle on which the reactance arcs terminate?
A. Prime axis
B. Reactance axis
C. Impedance axis
D. Polar axis

291. E9G06 (B) | On the Smith chart shown in Figure E9-3, what is the name for the large outer circle on which the reactance arcs terminate?
A. Prime axis
B. Reactance axis
C. Impedance axis
D. Polar axis

292. E9G07 | On the Smith chart shown in Figure E9-3, what is the only straight line shown?
A. The reactance axis
B. The current axis
C. The voltage axis
D. The resistance axis

293. E9G07 (D) | On the Smith chart shown in Figure E9-3, what is the only straight line shown?
A. The reactance axis
B. The current axis
C. The voltage axis
D. The resistance axis

294. E9G08 | What is the process of normalization with regard to a Smith chart?
A. Reassigning resistance values with regard to the reactance axis
B. Reassigning reactance values with regard to the resistance axis
C. Reassigning impedance values with regard to the prime center
D. Reassigning prime center with regard to the reactance axis

295. E9G08 (C) | What is the process of normalization with regard to a Smith chart?
A. Reassigning resistance values with regard to the reactance axis
B. Reassigning reactance values with regard to the resistance axis
C. Reassigning impedance values with regard to the prime center
D. Reassigning prime center with regard to the reactance axis

296. E9G09 | What third family of circles is often added to a Smith chart during the process of solving problems?
A. Standing wave ratio circles
B. Antenna-length circles
C. Coaxial-length circles
D. Radiation-pattern circles

297. E9G09 (A) | What third family of circles is often added to a Smith chart during the process of solving problems?
A. Standing wave ratio circles
B. Antenna-length circles
C. Coaxial-length circles
D. Radiation-pattern circles

298. E9G10 | What do the arcs on a Smith chart represent?
A. Frequency
B. SWR
C. Points with constant resistance
D. Points with constant reactance

299. E9G10 (D) | What do the arcs on a Smith chart represent?
A. Frequency
B. SWR
C. Points with constant resistance
D. Points with constant reactance

300. E9G11 | How are the wavelength scales on a Smith chart calibrated?
A. In fractions of transmission line electrical frequency
B. In fractions of transmission line electrical wavelength
C. In fractions of antenna electrical wavelength
D. In fractions of antenna electrical frequency

301. E9G11 (B) | How are the wavelength scales on a Smith chart calibrated?
A. In fractions of transmission line electrical frequency
B. In fractions of transmission line electrical wavelength
C. In fractions of antenna electrical wavelength
D. In fractions of antenna electrical frequency

302. E9H01 | When constructing a Beverage antenna, which of the following factors should be included in the design to achieve good performance at the desired frequency?
A. Its overall length must not exceed 1/4 wavelength
B. It must be mounted more than 1 wavelength above ground
C. It should be configured as a four-sided loop
D. It should be one or more wavelengths long

303. E9H
E9H – Receiving Antennas: radio direction finding antennas; Beverage Antennas; specialized receiving antennas; long wire receiving antennas

304. Receiving Antennas
Many antennas, such as the Beverage antenna, are designed to be receiving antennas only.
When constructing a Beverage antenna, one of the factors that should be included in the design is that it should be one or more wavelengths long to achieve good performance at the desired frequency. (E9H01)

305. Receiving Antennas
While directionality is a desirable feature for a receiving antenna, gain often is not, especially on the low bands.
The reason for this is that atmospheric noise is so high that gain over a dipole is not important for low band (160 meter and 80 meter) receiving antennas. (E9H02)

306. Direction finding antennas
Direction finding is an activity that’s both fun and useful.
One of the ways that it’s useful is to hunt down noise sources.
It can also be used to hunt down stations causing harmful interference.
A variety of directional antennas are used in direction finding, including the shielded loop antenna.
A receiving loop antenna consists of one or more turns of wire wound in the shape of a large open coil. (E9H09)
The output voltage of a multi-turn receiving loop antenna be increased by increasing either the number of wire turns in the loop or the area of the loop structure or both. (E9H10)

307. Direction finding antennas
An advantage of using a shielded loop antenna for direction finding is that it is electro- statically balanced against ground, giving better nulls. (E9H04)
The main drawback of a wire-loop antenna for direction finding is that it has a bidirectional pattern. (E9H05)
Sometimes a sense antenna is used with a direction finding antenna. The function of a sense antenna is that it modifies the pattern of a DF antenna array to provide a null in one direction. (E9H08)

308. Direction finding antennas
Another way to obtain a null in only one direction is to build an antenna array with a cardioid pattern.
One way to do this is to build an array with two dipoles fed in quadrature. 
A very sharp single null is a characteristic of a cardioid-pattern antenna is useful for direction finding. (E9H11)
Another accessory that is often used in direction finding is an attenuator.
It is advisable to use an RF attenuator on a receiver being used for direction finding because it prevents receiver overload which could make it difficult to determine peaks or nulls. (E9H07)

309. E9H01 | When constructing a Beverage antenna, which of the following factors should be included in the design to achieve good performance at the desired frequency?
A. Its overall length must not exceed 1/4 wavelength
B. It must be mounted more than 1 wavelength above ground
C. It should be configured as a four-sided loop
D. It should be one or more wavelengths long

310. E9H01 (D) | When constructing a Beverage antenna, which of
the following factors should be included in the design to achieve good performance at the desired frequency?
A. Its overall length must not exceed 1/4 wavelength
B. It must be mounted more than 1 wavelength above ground
C. It should be configured as a four-sided loop
D. It should be one or more wavelengths long

311. E9H02 | Which is generally true for low band (160 meter and 80 meter) receiving antennas?
A. Atmospheric noise is so high that gain over a dipole is not important
B. They must be erected at least 1/2 wavelength above the ground to attain good directivity
C. Low loss coax transmission line is essential for good performance
D. All of these choices are correct

312. E9H02 (A) | Which is generally true for low band (160 meter and 80 meter) receiving antennas?
A. Atmospheric noise is so high that gain over a dipole is not important
B. They must be erected at least 1/2 wavelength above the ground to attain good directivity
C. Low loss coax transmission line is essential for good performance
D. All of these choices are correct

313. E9H04 | What is an advantage of using a shielded loop antenna for direction finding?
A. It automatically cancels ignition noise in mobile installations
B. It is electro statically balanced against ground, giving better nulls
C. It eliminates tracking errors caused by strong out-of-band signals
D. It allows stations to communicate without giving away their position

314. E9H04 (B) | What is an advantage of using a shielded loop antenna for direction finding?
A. It automatically cancels ignition noise in mobile installations
B. It is electro statically balanced against ground, giving better nulls
C. It eliminates tracking errors caused by strong out-of-band signals
D. It allows stations to communicate without giving away their position

315. E9H05 | What is the main drawback of a wire-loop antenna for direction finding?
A. It has a bidirectional pattern
B. It is non-rotatable
C. It receives equally well in all directions
D. It is practical for use only on VHF bands

316. E9H05 (A) | What is the main drawback of a wire-loop antenna for direction finding?
A. It has a bidirectional pattern
B. It is non-rotatable
C. It receives equally well in all directions
D. It is practical for use only on VHF bands

317. E9H06 | What is the triangulation method of direction finding?
A. The geometric angles of sky waves from the source are used to determine its position
B. A fixed receiving station plots three headings to the signal source
C. Antenna headings from several different receiving locations are used to locate the signal source
D. A fixed receiving station uses three different antennas to plot the location of the signal source

318. E9H06 (C) | What is the triangulation method of direction finding?
A. The geometric angles of sky waves from the source are used to determine its position
B. A fixed receiving station plots three headings to the signal source
C. Antenna headings from several different receiving locations are used to locate the signal source
D. A fixed receiving station uses three different antennas to plot the location of the signal source

319. E9H07 | Why is it advisable to use an RF attenuator on a receiver being used for direction finding?
A. It narrows the bandwidth of the received signal to improve signal to noise ratio
B. It compensates for the effects of an isotropic antenna, thereby improving directivity
C. It reduces loss of received signals caused by antenna pattern nulls, thereby increasing sensitivity
D. It prevents receiver overload which could make it difficult to determine peaks or nulls

320. E9H07 (D) | Why is it advisable to use an RF attenuator on a receiver being used for direction finding?
A. It narrows the bandwidth of the received signal to improve signal to noise ratio
B. It compensates for the effects of an isotropic antenna, thereby improving directivity
C. It reduces loss of received signals caused by antenna pattern nulls, thereby increasing sensitivity
D. It prevents receiver overload which could make it difficult to determine peaks or nulls

321. E9H08 | What is the function of a sense antenna?
A. It modifies the pattern of a DF antenna array to provide a null in one direction
B. It increases the sensitivity of a DF antenna array
C. It allows DF antennas to receive signals at different vertical angles
D. It provides diversity reception that cancels multipath signals

322. E9H08 (A) | What is the function of a sense antenna?
A. It modifies the pattern of a DF antenna array to provide a null in one direction
B. It increases the sensitivity of a DF antenna array
C. It allows DF antennas to receive signals at different vertical angles
D. It provides diversity reception that cancels multipath signals

323. E9H09 | Which of the following describes the construction of a receiving loop antenna?
A. A large circularly polarized antenna
B. A small coil of wire tightly wound around a toroidal ferrite core
C. One or more turns of wire wound in the shape of a large open coil
D. A vertical antenna coupled to a feed line through an inductive loop of wire

324. E9H09 (C) | Which of the following describes the construction of a receiving loop antenna?
A. A large circularly polarized antenna
B. A small coil of wire tightly wound around a toroidal ferrite core
C. One or more turns of wire wound in the shape of a large open coil
D. A vertical antenna coupled to a feed line through an inductive loop of wire

325. E9H10 | How can the output voltage of a multiple turn receiving loop antenna be increased?
A. By reducing the permeability of the loop shield
B. By increasing the number of wire turns in the loop and reducing the area of the loop structure
C. By winding adjacent turns in opposing directions
D. By increasing either the number of wire turns in the loop or the area of the loop structure or both

326. E9H10 (D) | How can the output voltage of a multiple turn receiving loop antenna be increased?
A. By reducing the permeability of the loop shield
B. By increasing the number of wire turns in the loop and reducing the area of the loop structure
C. By winding adjacent turns in opposing directions
D. By increasing either the number of wire turns in the loop or the area of the loop structure or both

327. E9H11 | What characteristic of a cardioid pattern antenna is useful for direction finding?
A. A very sharp peak
B. A very sharp single null
C. Broad band response
D. High-radiation angle

328. E9H11 (B) | What characteristic of a cardioid pattern antenna is useful for direction finding?
A. A very sharp peak
B. A very sharp single null
C. Broad band response
D. High-radiation angle

329. Resources http://arrlexamreview.appspot.com/ Review by Subelement
Gives you the correct answer as you go.
I like it the best!!!
Is like taking the test for real.
Gives you the most information,
Sub-elements and percent %.

330. Yipee! That was the last slide!