1. Dimension Guidelines NOTE: Students will need a highlighter
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
Dimension Guidelines
Note: There are dozens of rules, do’s and don’ts, and guidelines associated with dimensioning. This purpose of this presentation is to introduce those guidelines that are most critical, and that students tend to have the most trouble with when first learning how to dimension drawings. Each slide has notes that provide references to textbooks that give further details on each guideline.
NOTE: Students will need a highlighter
Project Lead The Way, Inc.
Copyright 2007

2. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
1. Dimensions should NOT be duplicated, or the same information given in two different ways.
0.75
1.50
2.00
Incorrect
1.00
1.00
0.50
Project Lead The Way, Inc.
Copyright 2007

3. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
1. Dimensions should NOT be duplicated, or the same information given in two different ways.
References:
Pg 337 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 109 Fundamentals of Modern Drafting by Paul Wallach
Pg 425 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg 701 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Project Lead The Way, Inc.
Copyright 2007

4. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
2. No unnecessary dimensions should be used – only those needed to produce or inspect the part.
References:
Pg 109 Fundamentals of Modern Drafting by Paul Wallach
Pg 392 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Note: In a chain of dimensions, as seen with the width and height dimensions in the front view, one of the dimensions is unnecessary and must be removed. Overall dimensions for width, height, and depth must be present.
Incorrect
0.75
0.50
0.50
Project Lead The Way, Inc.
Copyright 2007

5. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
2. No unnecessary dimensions should be used – only those needed to produce or inspect the part.
References:
Pg 109 Fundamentals of Modern Drafting by Paul Wallach
Pg 392 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Note: In a chain of dimensions, as seen with the width and height dimensions in the front view, one of the dimensions is unnecessary and must be removed. Overall dimensions for width, height, and depth must be present.
Project Lead The Way, Inc.
Copyright 2007

6. Skip # 3

7. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
4. Whenever possible, avoid dimensioning to hidden lines and features.
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 134 Fundamentals of Modern Drafting by Paul Wallach
Pg 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg 703 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Incorrect
0.75
Project Lead The Way, Inc.
Copyright 2007

8. 4. Whenever possible, avoid dimensioning to hidden lines and features.
Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
4. Whenever possible, avoid dimensioning to hidden lines and features.
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 134 Fundamentals of Modern Drafting by Paul Wallach
Pg 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg 703 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Project Lead The Way, Inc.
Copyright 2007

9. Incorrect 5. Avoid dimensioning over or through the object. 1.00 1.00
Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
5. Avoid dimensioning over or through the object.
1.00
Incorrect
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 394, 404, 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg 692 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
1.00
.75
2.00
Project Lead The Way, Inc.
Copyright 2007

10. 5. Avoid dimensioning over or through the object.
Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
5. Avoid dimensioning over or through the object.
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 394, 404, 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg 692 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Project Lead The Way, Inc.
Copyright 2007

11. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
6. A dimension should be attached to only one view; for example, extension lines should not connect two views.
2.00
Reference:
Pg 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Incorrect
1.00
Project Lead The Way, Inc.
Copyright 2007

12. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
6. A dimension should be attached to only one view; for example, extension lines should not connect two views.
Reference:
Pg 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Project Lead The Way, Inc.
Copyright 2007

13. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
7. Whenever possible, locate dimensions between adjacent views.
1.00
Incorrect
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 108 Fundamentals of Modern Drafting by Paul Wallach
Pg 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
1.00
0.50
0.75
1.50
2.00
Project Lead The Way, Inc.
Copyright 2007

14. 7. Whenever possible, locate dimensions between adjacent views.
Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
7. Whenever possible, locate dimensions between adjacent views.
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 108 Fundamentals of Modern Drafting by Paul Wallach
Pg 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Project Lead The Way, Inc.
Copyright 2007

15. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
8. Avoid crossing extension lines, but do not break them when they do cross.
Multiple extension line crossings may be confused for the outside corner of the part.
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 394, 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg 690 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Note: Crossing extension lines is acceptable, but excessive numbers of crossings may confuse the viewer.
Project Lead The Way, Inc.
Copyright 2007

16. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
9. Whenever possible, avoid sending extension lines through object views.
Incorrect
Reference:
Pg Engineering Drawing and Design 3rd Edition by David Madsen et. al.
0.50
0.75
1.50
Project Lead The Way, Inc.
Copyright 2007

17. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
9. Whenever possible, avoid sending extension lines through object views.
Reference:
Pg Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Project Lead The Way, Inc.
Copyright 2007

18. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
10. In general, a circle is dimensioned by its diameter and an arc by its radius.
References:
Pg , Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 131, Fundamentals of Modern Drafting by Paul Wallach
Pg , , 427 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg , Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Project Lead The Way, Inc.
Copyright 2007

19. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
11. Holes are located by their centerlines, which may be extended and used as extension lines.
References:
Pg 44, 340 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg , 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Project Lead The Way, Inc.
Copyright 2007

20. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
12. Holes should be located and sized in the view that shows the feature as a circle.
Incorrect
1.00
References:
Pg 351 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 109 Fundamentals of Modern Drafting by Paul Wallach
Pg 411, 427 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg 693 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
0.50
ǿ0.50 THRU
Project Lead The Way, Inc.
Copyright 2007

21. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
12. Holes should be located and sized in the view that shows the feature as a circle.
References:
Pg 351 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 109 Fundamentals of Modern Drafting by Paul Wallach
Pg 411, 427 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg 693 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Note: The top view was removed, because it is not needed to completely communicate the object’s geometry.
Project Lead The Way, Inc.
Copyright 2007

22. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
13. Do not cross a dimension line with an extension line, and avoid crossing dimensions with leader lines.
1.00
ǿ0.50 THRU
2.00
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 394, 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
0.50
1.00
Project Lead The Way, Inc.
Copyright 2007

23. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
13. Do not cross a dimension line with an extension line, and avoid crossing dimensions with leader lines.
References:
Pg 342 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 394, 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Project Lead The Way, Inc.
Copyright 2007

24. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
14. Leader lines point toward the center of the feature, and should not occur horizontally or vertically.
References:
Pg 45, 344 Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg , , 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg , 703 Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Note: Slopes greater than 75° and less than 15° from horizontal should be avoided. A leader has a .25 in shoulder at one end that begins at the center of the vertical height of the lettering and an arrowhead at the other end point.
Project Lead The Way, Inc.
Copyright 2007

25. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
15. Dimension numbers should be centered between arrowheads, except when using stacked dimensions, and then the numbers should be staggered.
Incorrect
References:
Pg Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 137 Fundamentals of Modern Drafting by Paul Wallach
Pg 400, 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Note: The 0.50 dimension cannot fit in between its extension lines, and is placed to the outside of the common extension line to avoid confusion.
ǿ3.00 ǿ2.25 ǿ1.50
Project Lead The Way, Inc.
Copyright 2007

26. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
15. Dimension numbers should be centered between arrowheads, except when using stacked dimensions, and then the numbers should be staggered.
References:
Pg Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 137 Fundamentals of Modern Drafting by Paul Wallach
Pg 400, 426 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Project Lead The Way, Inc.
Copyright 2007

27. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
16. Concentric circles are dimensioned in the longitudinal view, whenever practical.
Incorrect
ǿ3.00
ǿ2.25
References:
Pg Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 407 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Note: This rule applies to shafts, not to holes.
ǿ1.50
Project Lead The Way, Inc.
Copyright 2007

28. Dimension Guidelines
Introduction to Engineering Design
Unit 2 – Lesson 2.2 – Dimensions and Tolerances
16. Concentric circles are dimensioned in the longitudinal view, whenever practical.
References:
Pg Engineering Drawing and Design 3rd Edition by David Madsen et. al.
Pg 407 Technical Drawing 9th Edition by Frederick Giesecke et. al.
Pg Technical Graphics Communication 3rd Edition by Gary Bertoline & Eric Wiebe
Note: This rule applies to shafts, not to holes.
Project Lead The Way, Inc.
Copyright 2007

29. DIMENSION GUIDELINES
20- DIMENSIONS SHOULD NOT BE LOCATED ON THE OUTSIDE BORDER AREA
21. ALL LENGTH DIMENSIONS START AT A COMMON SIDE OF THE SHAPE. THE SAME IS TRUE FOR THE HEIGHT AND WIDTH DIMENSIONS.