1. Control & Management Solutions
July 2009

2. Control & Management
There are various ways to control different equipment types and site conditions:
Dry controls
Measurements
Environment
Sensors / detectors
Communication
UPS and DC Systems
01:39

3. Older telecom equipment
Equipment control
Air Conditioners
Older telecom equipment
Access
Manufacturing
Generators
01:39

4. Equipment control
Check status and control operation of air conditioners.
Control industrial or custom process, like switching cooling fan on when internal street cabinet temperature gets too high.
Control older UPS and DC systems through their dry contact connection controls.
Check and operate generators using it’s control panel.
Access (barrier, gate, door) control via SMS or calls, with access database.
Remote control of all equipment by Internet or SMS.
Automatic response actions for situation changes.
Notifications on and/or SMS about all
events.
01:39

5. Electricity measurement Special low voltage sensors
KWH meters
Frequency
Special low voltage sensors
Voltage
Current
01:39

6. Electricity measurement
Various electrical measurements are supported.
High voltages require external transformer-less transducers that lower high voltages to <5v level.
High AC voltages can be lowered to <5v level by external transformer as well.
Direct isolated inputs for <60vDC and <40vAC are also available.
Measurement
Without adaptor
With adaptor
Adaptor type
AC voltage (V)
0÷40
0÷450
Transducer
DC voltage (V)
± 0÷60
± 0÷450
AC current (A)
0÷100
Current transformer
DC current
60mV measurement
DC Shunt
DC current (A)
Hall sensor
Frequency (Hz)
45÷65 (up to 40v)
45÷65
01:39

7. Environment and more
Fuel level
Humidity
Temperature
Gas
01:39

8. Environment and more
Humidity and temperature sensors can be installed and monitored.
Thresholds and hysteresis levels for alarms are configurable.
Wide list of generic sensors can be connected and monitored as well, operating at 0÷5Vdc or 0÷60mVdc.
Generic sensors include gas, fluid level in a tank, liquid flow, lighting, process control and more.
01:39

9. Process micro switch control Door/window detectors
Sensors and detectors
Smoke detectors
Water detectors
Process micro switch control
Motion detectors
Door/window detectors
01:39

10. Sensors and detectors
Security alarms can be sent based on events generated by smoke, water, flame, intruder, and motion detectors.
Any detector with dry contact indication can be connected.
Auxiliary operation voltage might be required by some types of detectors.
01:39

11. IT Control 01:39 Servers Switches / Routers Network printers
Workstations
01:39

12. IT Control
Servers, workstations, routers, switches, network printers, hardware firewalls and spam filters, and any other device with Ethernet connection can all be controlled by the IT Control feature.
Devices supporting SNMP (Simple Network Management Protocol) provide various status information: CPU load, hard drive space, physical and virtual memory, installed software, and list of running processes.
Detailed information can be viewed remotely.
Windows servers shutdown is integrated through free client software.
Manual and automatic LAN wakeup function is implemented.
01:39

13. Other manufacturer’s UPS
UPS and DC Systems
Other manufacturer’s UPS
PS1006 DC System
Power+ Modular UPS
µPS-SP Industrial UPS
Small UPS systems
01:39

14. UPS and DC Systems
Gamatronic UPS and DC Systems can be monitored through RS-232 serial communication port.
Notifications and alarms can be sent on SMS, , dry contacts.
Full information about UPS status and operation on the web interface.
Remote control actions (shutdown, load on bypass…).
Computers shutdown due to power failure or low battery condition.
Computer wake up after power failure.
Some other manufacturer’s UPS and DC Systems
are supported.
01:39

15. Practical applications: DATACENTER
Water was detected under the raised floor in unmanned computer room by water leakage detector. What can be automatically done to minimize the damage?
Send SMS notification to relevant people
Send shutdown signal to all servers
Operate local audio alarm by means of dry contact
Wait for emergency service
01:39

16. Practical applications: UNMANNED SITE
Thousand of cellular sites consume power, need security system and environmental controls. Only for knowing electricity consumption, personnel is being sent to every site once a month. How to minimize overall cost?
Management and Control unit is installed
All site parameters are monitored and reported
Emergency actions are programmed
Site access can be controlled
KWH meters power consumption is
accessible remotely
01:39

17. Practical applications: ACCESS CONTROL
Medium sized company has about 200 employees entering the underground parking every day. Electronic barrier controls entry. How to automate entry process without implementing expensive tag security system?
C&M unit is installed inside the barrier mechanism
Build internal database with employee’s phone numbers
In front of the barrier, they just dial in from the mobile
The gate will open by recognizing their phone number
The phone call will not be answered
by the unit, no cost since there was
no conversation
01:39

18. Gamatronic C&M Solutions: WING
WING is a simple cellular communication device. It is being installed on UPS and DC systems, and provides SMS alarms to the end user or control centers. On Power+ UPS, for example, the unit’s network board will automatically detect and start using the newly attached cellular modem for communication. Recipient's phone numbers are easily added through the user friendly web interface.
01:39

19. Gamatronic C&M Solutions: WING
SIM card is required
for GSM communication,
such as SMS or GPRS
12vDC operating voltage can be taken either from Power+ System Controller auxiliary voltage connector for battery backup, or from a provided 12v AC/DC adaptor. SIM card is required for operation, quad-band GSM modem provides worldwide cell network coverage.
Supported products:
DC Power Systems: PS1006, PS2012, 1UDC+
UPS Systems: µPS-SP, MST, Power+, Power+ SA
01:39

20. Gamatronic C&M Solutions: G4
G4 is a sophisticated control and management solution that includes embedded software with web interface and wide list of equipment monitoring options.
It can be installed as an added value for UPS or DC system, or just as a stand-alone site controller.
Fully configurable and programmable interface makes this unit highly flexible to fit any site and application.
Available in stand-alone or 19” rack mountable versions.
01:39

21. Gamatronic C&M Solutions: G4
Front panel includes:
Network connection
Extra RS-232 output (usually disabled)
Indicators
SIM card slot
Reset buttons
01:39

22. Gamatronic C&M Solutions: G4
Temperature sensor:
Rear panel includes:
Dry input contacts
Changeover dry output contacts
Temperature sensors connector (adaptor board included)
RS-232 serial communication port
Cellular antenna connection
12vDC connection
01:39

23. Gamatronic C&M Solutions: G4
G4 operates with dry contacts and temperature measurements for environment and equipment control. It can also communicate with a power device through RS232 serial communication port, and monitor computer equipment via the IT Control (Ethernet connection).
Connection
Amount
Remark
Dry inputs 8
N.O. / N.C. programmable
Dry outputs 4
Changeover (N.O. / COM. / N.C.)
Temperature 5
One sensor is included with the unit
RS-232 1
UPS / DC system comms., several protocols
Ethernet
Web / SNMP communication + IT Control
01:39

24. Gamatronic C&M Solutions: G4 web interface
Configuration and programming of G4 is performed through web interface, no software is required:
01:39

25. Gamatronic C&M Solutions: G4 web interface
IT Control monitors any equipment with IP address, and shows verbose information for SNMP-enabled devices:
01:39

26. Gamatronic C&M Solutions: G4 web interface
Serial device configuration helps to access all supported types of equipment with auto-detect feature:
01:39

27. Gamatronic C&M Solutions: G4 web interface
SMS notifications will be sent to specified cellular numbers, and according to the event type:
01:39

28. Gamatronic C&M Solutions: G4 web interface
The G4 will also accept external control through SMS messaging and reply to the initiator:
01:39

29. Gamatronic C&M Solutions:
G-Eye is the fully featured Site Manager. Monitoring and control options are extended compared with the G4. It also shows great emergency performance with it’s internal backup battery and front panel LCD.
Complete site monitoring includes more features, like KWH meters and power measurements.
Additional environmental control features include more options.
19” design to suit standard mounting equipment.
01:39

30. Gamatronic C&M Solutions:
Connection
Amount
Remark
Dry inputs 32
NO/NC programmable
Dry outputs 16
Changeover
Temperature 4
One sensor included
RS-232 1
UPS / DC system monitoring
Ethernet
Communication + IT Control
AC or DC volts / AC or DC amps 12
Transducer required > 40v/60vDC
Isolated DC volts / DC amps
Up to 60v or 60mV shunt
Frequency 2
Transducer required > 40v
kWH metering
Pulse reading only
Humidity
Precise 0÷100% measurement
Flood (with aux. voltage)
Special sensors available
Liquid level
Various sensors exist on market
01:39

31. Gamatronic C&M Solutions:
Servers
Safety
kWH
Air conditioners
Telecom equipment
UPS
Diesel generators
DC Power
Fuel level
Measurements
01:39

32. Gamatronic C&M Solutions:
With the G-Eye on the site, you receive the most complete data including live electricity measurements.
All this without unnecessary complications and costs involved in installation and maintenance.
All programming and fine tuning are performed remotely, without loosing the control even for a minute.
Universal input power and the backup battery features will ensure that appropriate procedures will be executed and alarms sent even during total site blackout.
Security is maintained by password protection on the web interface. No actions can be carried out without authentication.
01:39

33. Gamatronic C&M Solutions: G-Eye web interface
G-Eye electricity measurements are highly configurable, all of them include high/low alarms and hysteresis.
01:39

34. Gamatronic C&M Solutions: G-Eye web interface
All connected measurements must be calibrated carefully upon installation in order to achieve correct figures.
01:39

35. Gamatronic C&M Solutions: G-Eye web interface
Internal log of events can be downloaded in MS Excel format for additional processing.
01:39

36. Gamatronic C&M Solutions: G-Eye web interface
The complete configuration can be saved in a file and kept for backup, or used for configuring other units.
01:39

37. Gamatronic C&M Solutions: Management Software
Control centers require global centralized control over large amount of units and/or sites. GEMSi software is designed for both large control centers and compact, in-company monitoring.
Gamatronic
Element
Management
System
innovated
01:39

38. Gamatronic C&M Solutions: Management Software
Secure user-controlled interface with action logging allows direct access to regions and sites, either on country/county or factory/room level.
All Gamatronic and supported non-Gamatronic units can be put on one screen.
Alarms pop up and logged for all units, with user-defined severity.
Data logging is supported for detailed tracking of problematic site conditions.
Unlimited event logging.
Powerful, fully configurable reports generation supports excel output format.
Database backup/restore feature.
Includes all Gamatronic communication software.
01:39

39. Gamatronic C&M Solutions: Management Software
Easy map oriented navigation makes control simple and intuitive.
01:39

40. Gamatronic C&M Solutions: Management Software
Built in browser shows real-time data within GEMSi, without the need to open external windows.
01:39

41. Gamatronic hardware and software Control & Management solutions keep you confident and your site safe wherever you are at all times.
01:39