1. Ahmed Kulab Moh. Abed Foaad Al-Habeel
4/3/2019
The Islamic University of Gaza Engineering Faculty Electrical & Computer Department
Presentation About:
Electric Substations
Prepared by:
Ahmed Kulab Moh. Abed Foaad Al-Habeel
2003/ / /0463
Supervisor:
Dr.Basil Hamad
3 April 2019

2. Contents: What is a substation? Substation Functions Substation Types
- Step-up Transmission Substation
- Step-down Transmission Substation
- Distribution Substation
- Underground Distribution Substation
Substation Equipment
Conclusion
References
3 April 2019

3. What is a Substation?
A substation is a high-voltage electric system facility. It is used to switch generators, equipment, and circuits or lines in and out of a system. It also is used to change AC voltages from one level to another, and/or change alternating current to direct current or direct current to alternating current.
3 April 2019

4. 3 April 2019

5. Substation Functions
Substations are designed to accomplish the following functions, although not all substations have all these functions:
Change voltage from one level to another  
Regulate voltage to compensate for system voltage changes  
Switch transmission and distribution circuits into and out of the grid system  
Measure electric power qualities flowing in the circuits
3 April 2019

6. Eliminate lightning and other electrical surges from the system
Eliminate lightning and other electrical surges from the system  
Connect electric generation plants to the system   
Make interconnections between the electric systems of more than one utility  
Control reactive kilovolt-amperes supplied to and the flow of reactive kilovolt-amperes in the circuits
3 April 2019

7. Substation Types Step-up Transmission Substation
It receives electric power from a nearby generating facility and uses a large power transformer to increase the voltage for transmission to distant locations.
Step-down Transmission Substation
The step-down substation can change the transmission voltage to a subtransmission voltage. The subtransmission voltage lines can then serve as a source to distribution substations.
3 April 2019

8. Distribution Substation
Distribution Substations are located near to the end-users. Distribution substation transformers change the transmission or subtransmission voltage to lower levels for use by end-users.
Under Ground Distribution Substation
The same of distribution substations but it is underground.
3 April 2019

9. 3 April 2019

10. Substation Equipment
Air Circuit Breakers: These are used to interrupt circuits while current flows through them. Compressed air is used to quench the arc when the connection is broken.
                                                                                                                                                                                               
Batteries: These are used in the substation control house as a backup to power the control systems in case of a power blackout.
3 April 2019

11. Capacitor Bank: An array of capacitors connected into a circuit
Capacitor Bank: An array of capacitors connected into a circuit. Capacitors are used to control voltages supplied to the customer by eliminating the voltage drop in the system caused by inductive reactive loads.
Bus Support Insulators: These are porcelain or fiberglass insulators that serve to isolate the bus bar switches and other support structures and to prevent leakage current from flowing through the structure.
3 April 2019

12. 3 April 2019

13. Circuit Switchers: Circuit switchers a set of switches for redirecting current in a substation. Circuit switchers provide equipment protection for transformers, lines, cables, and capacitor banks. They also are used to energize and reenergize capacitor banks and other circuits.
Disconnect Switches: Disconnect switches or circuit breakers are used to isolate equipment or to redirect current in a substation.
3 April 2019

14. 3 April 2019

15. Distribution Bus: A distribution bus is a steel structure array of switches used to route power out of a substation.
High Voltage Underground Cables: High voltage cables are designed to carry high voltage current and are constructed in many different ways, but are usually shielded cables.
3 April 2019

16. Oil Circuit Breakers: Oil circuit breakers are used to switch circuits and equipment in and out of a system in a substation. They are oil filled to provide cooling and to prevent arcing when the switch is activated.
Current Transformers: Current transformers can be used to supply information for measuring power flows and the electrical inputs for the operation of protective relays associated with the transmission and distribution circuits or for power transformers.
3 April 2019

17. 3 April 2019

18. Power Transformers: Transformers raise or lower the voltage as needed to serve the transmission or distribution circuits.
Relays: A relay is a low-powered device used to activate a high-powered device. Relays are used to trigger circuit breakers and other switches in substations and transmission and distribution systems.
3 April 2019

19. Conclusion The substation operates as regulator for the voltage.
The main function for the substations convert the AC voltage from level to another .
The converting operation pass many steps and many substation.
The substations are used many equipments, the important equipments the transformers, Capacitors and safety devices.
3 April 2019

20. References www.atlaselectricinc.com/sub.html
3 April 2019

21. Thank You
3 April 2019