1. Presentation…
Hydronics Ltd.
Family of Products

2. CAMUS Hydronics is a world renowned manufacturer of Industrial, Commercial and Residential Boilers and Water Heaters.
The CAMUS corporate head office, manufacturing plant and warehouse are housed under one roof in a modern 68,000 square foot facility.

3. CAMUS products are constructed using state of the art components and high quality materials, engineered to operate with maximum efficiency, providing years of dependable service.
The CAMUS Product Development Team is comprised of the very best engineers and hydronic specialists in the industry, continually setting higher standards with every new product release.

4. The CAMUS CERTIFIED Seal assures you that RELIABILITY EFFICIENCY and SERVICEABILITY are built into every unit.

5. The CAMUS SERVICE LINE is open 24 hours a day 7 days a week!
CAMUS Hydronics is also a manufacturer of replacement parts for most copper finned water heaters and heating boilers as well as a supplier of specialty HVAC products.
The CAMUS SERVICE LINE is open 24 hours a day 7 days a week!

6. Extremely Low NOx!
THE DYNAFLAME IS AVAILABLE IN CONDENSING, NON-CONDENSING AND NEAR-CONDENSING MODELS WITH CAPACITIES RANGING FROM 500 UP TO 5,000 MBUTH!
Gas Fired Commercial Copper Tube Boilers for Hydronic Heating and Hot Water Supply

7. Standard Features
85% Efficiency (non-condensing) & 95% (condensing)
Suitable for Category 1 Installation
All Bronze and Copper Water Surfaces
Range of Burner Modulation of 20 – 100% (condensing)
Range of Burner Modulation of % (non-condensing)
Single Point Input Adjustment for Controlling Air and Gas
1 to 1 Gas/Air Ratio for perfect modulation throughout
Extremely low NOx Emissions Exceeding Air Quality
Standards (less than 10 PPM)
Flow Switch

8. Extremely Low Noise Level of Operation
Standard Features
(continued)
Very Small Footprint
Extremely Low Noise Level of Operation
Metal Fiber Knit Burner
Stainless Steel Outer Jacket & Combustion Chamber
Advanced Digital Control System with Pin Point Accuracy
Proven Hot Surface Ignition w/Soft Start for Rumble Free
Operation
Designed for Easy Access to Components for Maximum
Serviceability
Gasket-less Heat Exchanger Design

9. Maximum Allowable Working Pressure of 160 PSI
Standard Features
(continued)
Maximum Allowable Working Pressure of 160 PSI
Maximum Operating Water temperature of 250°F
24 volt Circuit Breaker
Protective Air Filter
Very low Gas Pressure Operation (down to 2” pressure inlet)
Main Burner Test Firing Valve
Temperature and Pressure Gauge
Inspected and Tested to ASME Requirements
Pressure Relief Valve

10. Optional Equipment
Secondary Exchanger for Condensing
Operation at 95% Efficiency
High Gas Pressure Switch
Low Gas Pressure Switch
Normally Open Vent Valve
Low Water Cut-Off
Flame Failure Alarm
Pump Delay
Outdoor Installation
Cupro Nickel Heat Exchanger
(standard on models 3500 and up)

11. Cross Sectionals

12. Control Panel Advanced digital display control w/pin point accuracy
Multi point diagnostic light package allowing for
Simple troubleshooting
Three pre-set modes of operation: Mode 1 for heating,
Mode 2 for domestic hot water heating and Mode 3 for
Operation by a remote controller
Adjustable pump delay feature based on a Temp.,
difference between inlet and outlet temperatures.
Displays inlet temperature, outlet temperature,
temperature rise, error messages and run time
Flame failure signal
Optional tank mounted sensor used in conjunction
with inlet sensor for domestic hot water application
Many more built-in features

13. Venting

14. Venting

15. DETAILED SPECIFICATIONS AVAILABLE ONLINE AND IN PRINTED LITERATURE
Heat Exchanger Head Loss & Flow
Recovery Capacities
MBTU Input and Output
Dimensional Specifications
Shipping Weights

16. Gas Fired Residential / Light Commercial Copper Tube Boilers for Hydronic Heating and Hot Water Supply
For Hydronic Heating – Models MFH60, 100, 150, 200, 250, 300, 400, 500, 600
For Hot Water Supply – Models MFW60, 100, 150, 200, 250, 300, 400, 500, 600 40

17. Performance Highlights
Low NOx
Up to 85% Efficiency – Non-Condensing Mode
Durable Ceramic Burner Unaffected by High Temperatures
Vents up to 60 Feet Horizontally with 50 Feet of Air Intake Duct
Suitable for Use in Negative Pressure Environments
Input Range From 60 to 600 MBTUH
Complete Diagnostic Light Package
Up to 95% Efficiency – Condensing Mode
Easy Access for Inspection and Cleaning of Heat Exchanger Tubes
Durable Ceramic Fiber Refractory
Simple to Service With Easy Access to Burner and Fan

18. Control Panel Accurate Proportional Control W/2-Stage Option
Incorporates Auto Reset High
Limit and Operator
Three Modes of Operation:
Heating, DHW & Remote
Port for Optional Tank Sensor
Displays Inlet/Outlet Temperatures and Delta Temperature
* The Smartflame Control Panel
is Optional
Optional Pump Delay
Flame Failure Feature
Displays Total Run HRS
Molex® Harness Connection for Ease of Service

19. DETAILED SPECIFICATIONS AVAILABLE ONLINE AND IN PRINTED LITERATURE
Heat Exchanger Head Loss & Flow
Recovery Capacities
MBTU Input and Output
Dimensional Specifications
Shipping Weights

20. For Hydronic Heating – Models MFH800, 1000, 1200, 1400, 1600, 1800, 2000
For Hot Water Supply – Models MFW800, 1000, 1200, 1400, 1600, 1800, 2000
Gas Fired Residential / Light Commercial Copper Tube Boilers for Hydronic Heating and Hot Water Supply

21. Performance Highlights
Low NOx
Up to 85% Efficiency – Non-Condensing Mode
Durable Ceramic Burner Unaffected by High Temperatures
Vents up to 60 Feet Horizontally with 60 Feet of Air Intake Duct
Suitable for Use in Negative Pressure Environments
Input Range From 800 to 2000 MBTUH
Complete Diagnostic Light Package
Up to 95% Efficiency – Condensing Mode
Easy Access for Inspection and Cleaning of Heat Exchanger Tubes
Durable Ceramic Fiber Refractory
Simple to Service With Easy Access to Burner and Fan
Performance Highlights

22. Control Panel Firing Modes Available: Accurate Proportional Control
with up to 4-Stage Option
Incorporates Auto Reset High
Limit and Operator
Port for Optional Tank Sensor
Displays Inlet/Outlet Temp’s
and Delta Temperature
Optional Pump Delay
Flame Failure Feature
Displays Total Run HRS
Molex® Harness Connection for Ease of Service
Weather Proof Enclosure
Fusible Link for Over-Voltage
Six Modes of Operation, for
Outdoor Reset, Heating, DHW
and Remote
Proven Field Performance
Firing Modes Available:
Models
On / Off
2-Stage
Models 1200 – 2000
3-Stage
4-Stage

23. DETAILED SPECIFICATIONS AVAILABLE ONLINE AND IN PRINTED LITERATURE
Heat Exchanger Head Loss & Flow
Recovery Capacities
MBTU Input and Output
Dimensional Specifications
Shipping Weights

24. For Hydronic Heating – Models MFNH2000, 2500, 3000, 3500, 4000
For Hot Water Supply – Models MFNW2000, 2500, 3000, 3500, 4000
Gas Fired Commercial / Commercial Copper Tube Boilers for Hydronic Heating and Hot Water Supply

25. Low NOx
Up to 85% Efficiency – Non-Condensing Mode
Durable Ceramic Burner Unaffected by High Temperatures
Vents up to 60 Feet Horizontally with 60 Feet of Air Intake Duct
Suitable for Use in Negative Pressure Environments
Input Range From 2000 to 4000 MBTUH
Complete Diagnostic Light Package
Up to 95% Efficiency – Condensing Mode
Easy Access for Inspection and Cleaning of Heat Exchanger Tubes
Durable Ceramic Fiber Refractory
Simple to Service With Easy Access to Burner and Fan

26. Accurate Proportional Control
With Up To 4-Stage Option
Incorporates Auto Reset High
Limit and Operator
Port for Optional Tank Sensor
Displays Inlet/Outlet Temp’s
And Delta Temperature
Optional Pump Delay
Flame Failure Feature
Displays Total Run HRS
Molex® Harness Connection for Ease of Service
Weather Proof Enclosure
Fusible Link for Over-Voltage
Six Modes of Operation, for
Outdoor Reset, Heating,
DHW, and Remote
Proven Field Performance
Firing Modes Available:
Models
On / Off
2-Stage
3-Stage
4-Stage

27. DETAILED SPECIFICATIONS AVAILABLE ONLINE AND IN PRINTED LITERATURE
Heat Exchanger Head Loss & Flow
Recovery Capacities
MBTU Input and Output
Dimensional Specifications
Shipping Weights

28. Gas Fired Commercial Copper Tube Boilers
Gas Fired Commercial / Commercial Copper Tube Boilers for Hydronic Heating and Hot Water Supply
Gas Fired Commercial Copper Tube Boilers
For Hydronic Heating and Hot Water Supply
For Hydronic Heating – Models CFH450, 550, 650
For Hot Water Supply – Models CFW450, 550, 650

29. Performance Highlights
Low NOx
Up to 85% Efficiency
Minimum Standby Losses with Estimated
Average AFUE Efficiencies of 82%
Durable Ceramic Burner not Affected by
Overheating
Vents up to 60 Feet Horizontally with 60 Feet of
Intake Air Duct
Suitable for Use in Negative Pressure Environments
Input Range From 450 to 650 MBTUH
Complete Diagnostic Light Package
Simple to Service With Easy Access to Burner
Performance Highlights

31. 2-Stage Proportional Control
Incorporates Auto Reset High Limit & Operator
Three Modes of Operation – Heating, DHW and Remote
Port for Optional Tank Sensor
Flame Failure Feature
Displays Inlet/Outlet Temperatures and
Delta Temperature
Displays Total Run Hours
Snap on Molex Connection for Easy Service
Weather Proof Enclosure
Fusible Link for Over-Voltage

33. DETAILED SPECIFICATIONS AVAILABLE ONLINE AND IN PRINTED LITERATURE
Heat Exchanger Head Loss & Flow
Recovery Capacities
MBTU Input and Output
Dimensional Specifications
Shipping Weights

34. Gas Fired Commercial Copper Tube Boilers
For Hydronic Heating and Hot Water Supply
For Hydronic Heating – Models BFH480, 660, 840, 1020, 1200, 1380, 1560, 1740, 1950
For Hot Water Supply – Models BFW480, 660, 840, 1020, 1200, 1380, 1560, 1740, 1950

36. Diagnostic Lights Help Troubleshoot Over the Phone
Durable Stainless Steel Burners
Adaptable to Outdoor Use
Simple to Service
Slide Out Burner Tray
Easy Side Access for Inspection of Combustion Chamber
Optional Digital Temperature Control is Extremely Accurate to
Minimize Standby Losses From Temperature Overshoot
High Temperature Ceramic Fiber Tiles in Combustion Chamber
Very Smooth and Quiet Operation
Suitable for Venting in Low Ceiling Applications with Use of
Power Venter and Low Profile Hood
Efficiencies of up to 83%

37. Incorporates Auto Reset High Limit & Operator
Three Modes of Operation:
Heating, DHW and Remote
Port for Optional Tank Sensor
Flame Failure Feature
Displays Inlet/Outlet Temp’s
And Delta Temperature
Displays Total Run Hours
Snap on Molex® Connection
For Easy Service
Fusible Link for Over-Voltage
Protection
* The Smartflame Control Panel
Is Optional

38. Venting

39. DETAILED SPECIFICATIONS AVAILABLE ONLINE AND IN PRINTED LITERATURE
Heat Exchanger Head Loss & Flow
Recovery Capacities
MBTU Input and Output
Dimensional Specifications
Shipping Weights

40. Gas Fired Commercial Copper Tube Boilers
For Hydronic Heating and Hot Water Supply
For Hydronic Heating – Models SFH420, 520, 600
For Hot Water Supply – Models SFW420, 520, 600

41. Temperature control is extremely accurate to
minimize standby losses from temp. overshoot
Diagnostic lights help troubleshoot over the phone
Input Range From 420 to 600 MBTUH
Burner runs cool and requires minimum maintenance
Adaptable to outdoor use
Simple to service
Very smooth and quiet operation
Fully enclosed combustion chamber
Suitable for venting in low ceiling applications
With use of power venter and low profile hood
Efficiencies up to 83%

43. Incorporates Auto Reset High Limit & Operator
Three Modes of Operation – Heating, DHW and Remote
Port for Optional Tank Sensor
Flame Failure Feature
Displays Inlet/Outlet Temperatures and
Delta Temperature
Displays Total Run Hours
Snap on Molex Connection for Easy Service
Weather Proof Enclosure
Fusible Link for Over-Voltage Protection

44. Venting

45. DETAILED SPECIFICATIONS AVAILABLE ONLINE AND IN PRINTED LITERATURE
Heat Exchanger Head Loss & Flow
Recovery Capacities
MBTU Input and Output
Dimensional Specifications
Shipping Weights

47. Standard Features
Constant or Outdoor Reset temperature control
Optional heating load matching software
Domestic target water temperature limit to prevent
boiler condensation or to maintain domestic hot water
heat exchanger temperature
Maximum target water temperature limit to prevent
individual boiler limit tripping
Warm weather shutdown of boilers and main pump(s)

48. Controls any type or combination of modulating & staging
boilers – 12 outputs per controller – each modulating boiler
uses 2 outputs, each staging boiler uses 1 output per stage;
each pump uses 1 output. Some possible control
configurations for a single controller application include:
- controls up to 6 modulating boilers
- controls up to 5 modulating boilers + 2 main pumps
- controls up to 4 modulating boilers
+ 2 single stage boilers + 2 main pumps
- controls up to 3 modulating boilers + 3 two-stage boilers
Standard Features
(CONTINUED)

49. Runtime based lead / lag control of boilers, regardless of type
Master – Slave arrangement allows for additional
controllers to be added to increase the boiler control
capability. In this manner, with 2 controllers, 24 outputs
are available (up to 12 mod boilers, or combination of
mod and staging boilers)
Totally custom firing sequences available to allow high
efficiency boilers to fire first followed by less efficient boilers
Runtime based lead / lag control of main system pumps,
comes with flow sensing & automatic lag pump switch-over
in case lead pump should fail
Standard Features
(CONTINUED)

50. Lock & key(s) to prevent unauthorized editing of parameters
EMS (Energy Management System) interfaces:
- enable / disable of heating controller (EMS enables or
disables heating system
- remote set point control of heating system (EMS provides
one control override (DO) and one 0-20ma signal (AO)
to Stage-Mod to take full control of Stage-Mod target
temperature)
Web / LAN server interface allowing each controller to
communicate to any PC web-browser application
Custom serial protocols available
Optional Features

51. Remote Set-point Option
Allows EMS interfacing
to Stage-Mod
Web Server Option
Web / LAN server module
for Stage-Mod
Customizing Options(s)
Project specific customization
available on request
Add On Options

53. LCD Display
Power On
Outdoor Temperature
System Water Temperature
Target Water Temperature
Set Point
Ratio Setting
Throttling
Outdoor Start-up Temperature

54. Standard Features
Indoor / Outdoor Sensors are solid state and capable of maintaining accuracy at a maximum wire length of 4,000 feet of shielded cable
Power Relays are Socket - Mounted and replaceable on site
Control is equipped with Boiler Override and Boiler By-Pass Switches
Capable of Fully Modulating the Gas Input of the Boilers
Automatically shuts down the heating unts as a Preset Outdoor Temperature which is variable between 50 and 100° F
Can be mounted in an enclosure suitable for wall mounting
Has a Minimum Boiler Water Temperature Setting independent of and   capable of Overriding the Scheduled Function. This setting is variable   between 90 and 150°F

55. Standard Features (cont’d)
Allows for Automatic Switching of the Lead Boiler
LED liights on the front door panel to indicate a "Boiler in Fault" alarm
Control is equipped with Boiler Override and Boiler By-Pass Switches
All Boiler Status Information is accessible from a Remote Location via the   CM8 Central Control Panel
Boiler Control communicates through the "Camus Communication Interface"   to LonWorks, BACnet and other systems.

56. Thank-You!