1. POWER EQUIPMENT INSTRUCTOR: ROBERT A. MCLAUGHLIN ZAILI THEO ZHAO
12:36
POWER EQUIPMENT INSTRUCTOR: ROBERT A. MCLAUGHLIN ZAILI THEO ZHAO
HIGH PRESSURE FITTINGS
WEEK 13

2. Learning Objectives A boiler and pressure vessel.
12:36
A boiler and pressure vessel.
A level 1 boiler and a critical pressure boiler.
The various pressure fittings used on boilers.
The types of safety valves on boilers.
The components of a boiler gauge glass.
The proper procedures for removing a boilers gauge glass from service, disassembly of the gauge, inspection and replacement and rebuild of a typical gauge glass.

3. Boiler
12:36
A steam boiler is a closed pressure vessel in which water is heated to generate saturated steam.
The water is heated by the gasses of combustion.
A pressure vessel that produces hot water heated by the gasses of combustion is also a boiler.

4. Boiler - classification
12:36
Boilers can be divided into two pressure related categories:
Low pressure – boilers operating at 15 psi and below.
High pressure – boilers operating above 15 psi.

5. Boilers can also be categorized into Level ratings.
12:36
Boilers can also be categorized into Level ratings.
A Level 1 boiler is
When the temperature and pressure of a boiler equals 1500 or more.
All of the components of a level one boiler designed with a safety factor of 5 and are tested and given serial numbers.

6. WHAT IS THE FACTOR OF SAFETY?
12:36
Ultimate strength divided by allowable working stress or bursting pressure divided by safe working pressure.
It can vary between four and seven depending on age, type of construction, and condition.
Use five for most calculations

7. Critical pressure Many boilers operate at pressures 1000 to 3000 psi.
12:36
Many boilers operate at pressures 1000 to psi.
Some operate at critical pressure – 3206 psi and oF
Critical pressure is the pressure at which steam and water at the same density.
All critical pressure boilers must have separate a pump to create circulation.

8. External fittings and connections
12:36
Drains
All steam and water sections must have these.
The superheater will have drains.
The drums and headers will have drains.

9. External fittings and connections
12:36
Vent
high pressure globe valve at high point in the boiler
used when filling and emptying the boiler.

10. External fittings and connections
12:36
Sample connections
used for taking boiler water samples.
Drains, vents, and sampling connections will all have high pressure rated globe valves attached to the connection.

11. External fittings and connections
12:36
Feed stop and check valves
to manually regulate the flow of water to the drum.

12. External fittings and connections
12:36
Steam stop valves
located at the superheater and desuperheater outlets.
Used to cut the boiler in or out of the main steam line.

13. External fittings and connections
12:36
Safety valve
two types (huddling chamber and nozzle reaction type).
They are not relief valves.
Question
What is the difference between the safety and relief valves?

14. External fittings and connections
12:36
Soot blower
Fixed and retractable

15. Internal fittings
12:36

16. 12:36

17. External fittings and connections
12:36
Water gage glass – attached directly to the drum, they allow the operator to see the water level in the drum.
All boilers operating over 400 psi are required to have two independent means of determining water level.
One will be a gauge glass attached directly to the steam drum; one will be a remote water level indicator.

18. External fittings and connections
12:36
Temperature and pressure gauges
Superheated steam flow indicators

19. the operator control the safe operation of the boilers.
12:36

20. Gauge Glass Two independent means of indication
12:36
Two independent means of indication
These can consist of two gauge glasses attached to the drum, or a single gauge glass, and a remote water level indicator.
A gauge is located so that:
the lowest visible part of the glass is 2” above the lowest permissible drum water level
the upper most visible part of the glass is located 2” below the upper most

21. Gauge Glass
12:36
Boilers operating at pressures below 250 psi can be fitted with tubular type gauge glasses
Above 250psi, flat type gauge glasses are required.
Isolation valves are required on each leg of the gauge glass

22. Gauge Glass
12:36
There are high pressure glass type indicators that can be used instead of flat gauge glasses,
for example, bicolor gauge glasses.
Figure gauge glasses work on the principle of light refraction

23. Gauge Glass
12:36
Every gauge glass will have valves to isolate the gauge from the drum pressure for maintenance and emergency situations.
The isolation valves are usually of the quick closing type, capable of being closed with ¼ turn of the handles.
The handles will be connected by chain pulls so that an operator can pull on the chain and close both valves at the same time from a remote location.
The bottom isolation valve will always be fitted with a ball check device to prevent hot water from flowing through a broken gauge glass.

24. Gauge Glass
12:36
Each gauge glass assemble will be fitted with a blowdown connection to:
Insure that the connections between the drum and gauge do not become clogged.
To help the operator tell the level in the glass.
If you are in doubt of the level in the glass, blow the glass down (open the gauge drain valve).
If you blow a glass down, and you see the water level go up through the glass, then the drum level is high.
If no level appears, then the level is high.

25. Gauge Glass
12:36
Leaks above the actual water level will indicate higher than normal levels.
Leaks below the actual level will indicate lower than normal levels.

26. Gauge Glass To blow a glass down for normal maintenance:
12:36
To blow a glass down for normal maintenance:
Disconnect the pull chains
Close the top valve and open the drain valve (blowdown valve). Let it drain for a few seconds.
Open the top isolation valve and close the bottom isolation valve. Leave the drain open for a few more seconds.
Close the drain valve.
Open the bottom isolation valve and reattach the chains.

27. Flat type of Gauge glass construction
12:36
BODY
FLAT GUAGE GLASS
MICA SHEET
ASBESTOS GASKETS
ASBESTOS CUSHIONS
COVERPLATES
STUDS
NUTS 

28. Gauge Glasses and Try Cocks
12:36
Both the water column and gauge glass must blowdown daily
Prevent sludge accumulations from blocking lines
Observe the level when it is blown.
When the valve is opened, the water should drop out of the glass rapidly.
When the valve is closed, it should return rapidly to its previous level.
If the glass water drains slowly
This is an indication of clogging up.
The situation must be corrected as quickly as possible, even if the coiler has to be shut down.

29. There is one adjustment on the muddling chamber type safety valve
12:36
There is one adjustment on the muddling chamber type safety valve
Adjusting ring
Question
Who can adjust the boiler safety setting pressure?

30. There are two adjustments
12:36
There are two adjustments
Adjusting ring
Nozzle ring
Question
How to increase the blowdown pressure?

31. The wires for remote releasing safety valve
12:36

32. Gate valve rise stem
12:36

33. Globe valve
12:36

34. Swing check valve
12:36

35. Ball valve
12:36

36. Butterfly valve
12:36

37. Marine boiler example what are these fittings?
12:36
1 - Gauge Glass or Water Column
2 - Main Steam, Safety, Auxilary Steam Valves
3 - Pressure Gauge
4 - Surface Blow
5 - Skin Valve (through ship's side)
6 - Bottom Blow
7 - Hydrokineter (to increase water circulation)
8 – Furnaces
9 - Fire-Tube bundles
10 - Main Feed Valve
11 - Auxiliary Feed Valve
12 - Deep Blue sea

38. 12:36

39. 12:36
THANK YOU