Presentation is loading. Please wait.

Presentation is loading. Please wait.

Designing of Helical divertor

Published byBruce Nelson Modified over 5 years ago

Similar presentations

Presentation on theme: "Designing of Helical divertor"— Presentation transcript:

1 Designing of Helical divertor
Example Design for Divortor (Oxide) Dispersion Strengthening method Armor Materials Pipe Heat Sink Materials Stable Nano-oxide particles in matrix Inhibition of dislocation motion Improvement of the strength and resistance of irradiation Dispersed particles Matrix (Cu) μm Dislocation Adoption to Copper alloy Dispersion Strengthening by aluminum compound Dispersion Strengthening by Zirconium compound Cu Cu Al Zr “Tensile strength”∝”Increase of dispersed particles”⇒Contribution as a strengthening particle （Success of DS method on Cu alloy）

Download ppt "Designing of Helical divertor"

Similar presentations

Titanium Melts at 1670°C Density 4.51 g cm -3 80% of Ti used in aerospace Use restricted to < 400°C.

Titanium Melts at 1670°C Density 4.51 g cm -3 80% of Ti used in aerospace Use restricted to < 400°C.
Phases and the Phase Diagram

Phases and the Phase Diagram
Strengthening Mechanisms Metallurgy for the Non-Metallurgist.

Strengthening Mechanisms Metallurgy for the Non-Metallurgist.
Electrodes and Tooling. Lesson Objectives When you finish this lesson you will understand: The various electrode materials and design Electrode and part.

Electrodes and Tooling. Lesson Objectives When you finish this lesson you will understand: The various electrode materials and design Electrode and part.
Key: Compound Calculations and Compound Stoichiometry.

Key: Compound Calculations and Compound Stoichiometry.
The American University in Cairo Mechanical Engineering Department MENG 426: Metals, Alloys & Composites Interactive MENG 426 Lab Tutorials Experiment.

The American University in Cairo Mechanical Engineering Department MENG 426: Metals, Alloys & Composites Interactive MENG 426 Lab Tutorials Experiment.
TED Thermomechanical Analyses Esposito Raffaele EN-STI-TCD.

TED Thermomechanical Analyses Esposito Raffaele EN-STI-TCD.
% X = (total atomic mass of X / molar mass which contains X)

% X = (total atomic mass of X / molar mass which contains X)
Chemical Reactions …fun for all…. Synthesis A + B AB Magnesium + Chlorine Mg 2+ + Cl 1- The ionic charge of Mg is 2+ because it must give away two electrons.

Chemical Reactions …fun for all…. Synthesis A + B AB Magnesium + Chlorine Mg 2+ + Cl 1- The ionic charge of Mg is 2+ because it must give away two electrons.
Grain boundary strengthening (Hall-Petch strengthening)

Grain boundary strengthening (Hall-Petch strengthening)
STRUCTURAL TRANSFORMATIONS IN Al-Cu COMPOSITE I. S. Los', A. V. Khorin, G. V. Kozlov, and A. V. Pryshchak Penza State University XII International Symposium.

STRUCTURAL TRANSFORMATIONS IN Al-Cu COMPOSITE I. S. Los', A. V. Khorin, G. V. Kozlov, and A. V. Pryshchak Penza State University XII International Symposium.
Chapter 11 The Mole A chemists best friend  Counting units in groups is common  Dozen  Case  Gross  Mole - a particular number of atoms, ions, molecules.

Chapter 11 The Mole A chemists best friend  Counting units in groups is common  Dozen  Case  Gross  Mole - a particular number of atoms, ions, molecules.
Percent Composition Parts of a Whole. Percent Short for per centum …”by the hundred” Part of a whole If there are 10 people in a room and 4 of them have.

Percent Composition Parts of a Whole. Percent Short for per centum …”by the hundred” Part of a whole If there are 10 people in a room and 4 of them have.
Dispersion and Solution Hardening

Dispersion and Solution Hardening
Chemical Calculations Stoichiometry OBJECTIVES: – Calculate stoichiometric quantities from balanced chemical equations using units of moles and mass.

Chemical Calculations Stoichiometry OBJECTIVES: – Calculate stoichiometric quantities from balanced chemical equations using units of moles and mass.
B. Titanium-based Alloys Titanium is hcp at room temperature – and transform to the bcc structure on heating to 883 o C. Alloying elements are added to.

B. Titanium-based Alloys Titanium is hcp at room temperature – and transform to the bcc structure on heating to 883 o C. Alloying elements are added to.
Molar Mass & Percent Composition. The mass of 1 mole of an element or compound – The mass in grams from the Periodic Table Unit = grams per mole (g/mol)

Molar Mass & Percent Composition. The mass of 1 mole of an element or compound – The mass in grams from the Periodic Table Unit = grams per mole (g/mol)
Chemical Calculations Stoichiometry u OBJECTIVES: Calculate stoichiometric quantities from balanced chemical equations using units of moles, mass, representative.

Chemical Calculations Stoichiometry u OBJECTIVES: Calculate stoichiometric quantities from balanced chemical equations using units of moles, mass, representative.
Chad Allen, Devon Rood, Kurt Core.  Connects the aileron to plane.

Chad Allen, Devon Rood, Kurt Core.  Connects the aileron to plane.
EXTRACTIVE METALLURGY OF ALUMINIUM Intro: Aluminium is the most abundant metal in Earth. It occurs in nature in the form of aluminium oxide and other combined.

EXTRACTIVE METALLURGY OF ALUMINIUM Intro: Aluminium is the most abundant metal in Earth. It occurs in nature in the form of aluminium oxide and other combined.

Similar presentations

Ads by Google