1. Atomic Force Microscopy

2. Atomic force microscopy (AFM) is a very-high-resolution type of scanning probe microscopy(SPM), with high resolution on the order of fractions of a nanometer, more than 1000 times better than the optical microscopy.
The information is gathered by "feeling" or "touching" the surface with a mechanical probe.

3. Background and History
1981 – Swiss scientists Gerd Binnig and Heinrich Rohrer- Atomic resolution microscopy,
simple
1986 – Nobel prize

4. General Applications 1 2 3
Materials Investigated: Thin and thick film coatings, ceramics, composites, glasses, synthetic and biological membranes, metals, polymers, and semiconductors.
Used to study phenomena of: Abrasion, corrosion, etching (scratch), friction, lubricating, plating, and polishing.
AFM can image surface of material in Nano resolution and also measure force at the nano- scale.

5. Further Applications

6. Parts of AFM 1. Laser (Illumination)– deflected off cantilever
2. Mirror –reflects laser beam to photo detector
3. Photo detector –dual element
photodiode that measures differences in light intensity and converts to voltage
4. Amplifier- amplifies the signal
5. Recorder
6. Sample
7. Probe –tip that scans sample
made of Si
8.Cantilever –moves as scanned over sample and deflects laser beam

8. Principle
The AFM consists of a cantilever with a sharp tip (probe) at its end that is used to scan the specimen surface.
The cantilever is typically silicon or silicon nitride with a tip radius of curvature on the order of nanometers.
When the tip is brought into proximity of a sample surface, laser beam activates the forces between the tip and the sample lead to a deflection of the cantilever.
Depending on the situation, forces that are measured in AFM include mechanical contact force, van der Waals forces, capillary forces, chemical bonding, electrostatic forces.

9. How Does AFM Work?

11. Scanners
AFM scanners are made from piezoelectric material, which expands and contracts proportionally to an applied voltage.
Peizo electric material- Barium titanate, Zirconium titanate
Whether they elongate or contract depends upon the voltage applied.
Traditionally the tip or sample is mounted on a 'tripod' of three piezo crystals, with each responsible for scanning in the x,y and z directions.
Because of differences in material or size, the sensitivity varies from scanner to scanner.

12. Experimental Procedures
Sample preparation
Measuring
3-D Imaging
Manipulating/Analyzing
Thin layer of wax on steel disk

13. Diagram
Measuring
-3 D Imaging
Analysing

14. Scanning the Sample/measure
Tip brought within nanometers of the sample (Van der Waals)
Radius of tip limits the accuracy of analysis/ resolution
Stiffer cantilevers protect against sample damage because they deflect less in response to a small force

15. Data Analysis Morphology Characterization/ Sub microscopic level
Surface roughness quantification
Will be analyzed
Physical properties/ Swelling, cohesiveness, smoothness

16. AFMTips
FIB- Focused ion beam

17. THREE Modes: Contact mode, Non-contact, mode, Tapping Mode
A.Contact Mode; hard, stable samples in air or liquid
Non-Contact Mode: non- invasive sampling.
Tapping (Intermittent contact): No shear and damaging samples

18. A. Contact Mode Measures repulsion between tip and sample
Force of tip against sample remains constant
Problems: excessive tracking forces applied by probe to sample- sample will destroy.

19. B. Non-Contact Mode Measures attractive forces between tip and sample
Tip doesn’t touch sample
Van der Waals forces between tip and sample detected
Problems: Can’t use with samples in fluid
Used to analyze semiconductors
Doesn’t degrade or interfere with sample- better for soft samples

20. C. Tapping (Intermittent- Contact) Mode
Tip vertically oscillates between contacting sample surface and lifting of at frequency of 50,000 to 500,000 cycles/sec.
Oscillation amplitude reduced as probe contacts surface due to loss of energy caused by tip contacting surface
Advantages: overcomes problems associated with
friction, adhesion, electrostatic forces
More effective for larger scan sizes

22. Advantages and Disadvanteges of AFM

23. In general

24. The future of AFM
Sharper tips by improved micro-fabrication processes: (tip – sample interaction tends to distort or destroy soft biological molecules )
development of more flexible cantilever springs and less damaging and non-sticky probes needed

25. Nano-Identification on Fiber surface
Cotton
Viscose Rayon
MMF